Search results for "Mécanique"
showing 10 items of 83 documents
Quasi-static behaviour and damage assessment of flax/epoxy composites
2015
Experimental investigations were conducted on flax and E-glass fibres reinforced epoxy matrix composites subjected to quasi-static loadings. Flax/epoxy samples having [0]12, [90]12, [0/90]3S and [±45]3S stacking sequences, with a fibre volume fraction of 43% have been tested under tension, compression and in-plane shear loadings. Overall, the compression strength of glass/epoxy was 76% greater than for the flax/epoxy composite. The damage evolution of flax/epoxy of [0/90]3S and [±45]3S samples has been evaluated in terms of transverse crack densities with respect to the load increment. The crack density exhibited a classical “S” shaped pattern for [0/90]3S and linearly for [±45]3S specimens…
Automatic measurement of wood fiber orientation and knot detection using an optical system based on heating conduction.
2015
In this paper, a new approach to computing the deviation of wood grain is proposed. To do this, the thermal conduction properties of timber are used (higher conduction in the fiber direction). Exciting the surface of the wood with a laser and capturing the thermal conduction using a thermal camera, an ellipse can be observed. Using a method similar to the tracheid effect, it is possible to extract information from this ellipse, such as the slope of grain and the presence of knots. With this method it is therefore possible to extend the mechanical model (assessing the mechanical properties of timber) to take certain singularities into account. Using this approach, the slope of grain can be e…
Fibre extraction from oleaginous flax for technical textile applications: influence of pre-processing parameters on fibre extraction yield, size dist…
2017
International audience; Cultivated primarily for its seeds, oleaginous flax could also be valued for the different fractions that can be extracted from the straw. However, as the straws are not harvested with the same technique and care than for the textile flax, the classical scutching technique cannot be used. As a consequence, an “all fibre” device was used to perform the separation of the different constituents of the oleaginous flax straws. The different fractions were quantified for two retting levels and for two degrees of rewetting of the stems. The physical and mechanical properties of fibres were then evaluated. It appears that the relative amount of fibres extracted from oleagino…
Springback of thick sheet AHSS subject to bending under tension
2012
Lien vers la version éditeur : http://www.sciencedirect.com/science/article/pii/S0020740312000677 The springback behavior of four advanced high-strength sheet steels (Dual-Phase, TRIP, ferrite-bainite) with thicknesses ranging from 1.2 to 4 mm was investigated by means of the bending-under-tension (BUT) test. The applicability of several guidelines from the literature was investigated experimentally and numerically. The monotonic decrease of springback as back force increased was confirmed for this category of sheet steels, and a general trend for the non-linear influence of the tool radius was observed. The influence of numerical factors on the predicted values of springback was investigat…
On the optimization of the cutting conditions for an improved corrosion resistance of OFHC copper
2018
International audience; Machining has a particular impact on the surface integrity and on corrosion resistance of components. In fact, material removal induces geometrical, mechanical and micro-structural modifications in the machined surface and sub-surface that alter the electrochemical behavior of the material, and so the aging process. In this study, oxygen free high conductivity copper (OFHC) has machined under orthogonal cutting conditions using uncoated cemented carbide tools. Then, the corrosion resistance in 0.1 M NaCl salt fog atmosphere of the machined samples is analyzed. Finally, the optimal cutting conditions, including the tool geometry, for an improved corrosion resistance a…
Aluminum to titanium laser welding-brazing in V-shaped grooveI
2017
International audience; Laser assisted joining of AA5754 aluminum alloy to T40 titanium with use of Al-Si filler wires was carried out. Continuous Yb:YAG laser beam was shaped into double spot tandem and defocalized to cover larger interaction zone in V shaped groove. Experimental design method was applied to study the influence of operational parameters on the tensile properties of the joints. Microstructure examination and fractography study were carried out to understand the relation between local phase content and fracture mode.Within defined window of operational parameters, statistically important factors that influenced the strength of T40 to AA5754 joints in V groove configuration w…
Friction Model for Tool/Work Material Contact Applied to Surface Integrity Prediction in Orthogonal Cutting Simulation
2017
Abstract Tribological behavior at both tool/chip and tool/work material interfaces should be highly considered while simulating the machining process. In fact, it is no longer accurate to suppose one independent constant friction coefficient at the tool/chip interface, since in reality it depends on the applied contact conditions, including the sliding velocity and pressure. The contact conditions at both above mentioned interfaces may affect the thermal and mechanical phenomena and consequently the surface integrity predictions. In this article, the influence of contact conditions (sliding velocity) on the tribological behavior of uncoated tungsten carbide tool against OFHC copper work mat…
Multi-experimental study of micro-structural and mechanical consequences of thermal cycles applied to a martensitic stainless steel « APX4 »
2010
The Direction des Applications Militaires at the Commissariat à l’Énergie Atomique, a French government-funded technological research organisation, selected a low carbon chromium rich martensitic stainless steel (APX4) to manufacture components with high yield strength and ultimate tensile strength. As such, this thesis is developed around three main axes. Firstly, the thesis summarizes the existing bibliography on this steel as well as its neighboring nuances. Secondly, it engages in a precise characterization of the material that is currently used for industrial manufacturing. Finally, this highly experimental work undertakes to observe and interpret the micro-structural and mechanical co…
Towards a local approach to fatigue, for the calculation of structures, applied to continuous fibre reinforced composite materials and structures
2018
The original concept of mechanical fatigue was linked to the failure of structures and was treated at first within the framework of Fracture Mechanics. Models developed to explain this phenomenon must therefore be able to be applied to structures: changing the structure means changes to the model and its identification. It is therefore judicious to develop models capable of treating both the damage processes and also able to be used within a local framework: to this end a method based on Damage Mechanics seems appropriate. This approach has long been employed and requires only the identification of damage processes at the level of the RVE (Representative Volume Element) to be used for any s…
Directionnalité graphique et dominance manuelle : une perspective développementale et interculturelle
2012
In the present work, we try to provide some understanding about the factors underlying the directional tendencies, by examining the impact of biomechanical constraints and cultural habits on directionality in graphic movements. French and Syrian subjects, children and adults, were compared in six experiments in order, to put in evidence the cognitive and psychomotor differences caused by the fact that the Eastern and Western cultures oppose on the directionality of writing and reading habits, and that the two hands are opposite in the directionality by adopting movements determined by biomechanical constraints. Likewise, this comparison allowed us to determine the relative strength of these…