Search results for "NET"
showing 10 items of 55461 documents
Optimum Design and Performance of an Electron Gun for a Ka-Band TWT
2019
This paper deals with optimum design and development of a thermionic electron gun to meet specified beam requirements within defined electric and geometric constraints for a Ka -band traveling wave tube (TWT) for space applications. The electron gun design is based on the Pierce method and carried out according to the iterative process indicated by Vaughan. The design of a periodic permanent magnet (PPM) beam focusing system for the stability of the beam is also required. A sensitivity analysis, by varying electric parameters and geometric parameters, is presented and taken into account as a fundamental role to the aim of optimizing the design of the Pierce gun. A cathode current value of 5…
Design and analysis of non-linear circuit with tunnel diode for hybrid control systems
2018
Electric circuits with tunnel diode's represent a classical example of dynamic systems with nonlinearities, which feature piecewise negative damping and multiple equilibria and, as consequence, nontrivial trajectories in the state-space. In this paper, we describe the experimental design and analysis of an electrical circuit, including a tunnel diode, allowing for a storage behavior with bistable output voltage states - low and high. The system is modeled for simulation and an experimental setup is designed and implemented in order to run a formal verification on different tools, applying a variety of hybrid control methods. The nonlinear diode's characteristic curve is experimentally deter…
Photoluminescence-Based Spatially Resolved Temperature Coefficient Maps of Silicon Wafers and Solar Cells
2020
In this article, we present a method to obtain implied open-circuit voltage images of silicon wafers and cells at different temperatures. The proposed method is then demonstrated by investigating the temperature coefficients of various regions across multicrystalline silicon wafers and cells from different heights of two bricks with different dislocation densities. Interestingly, both low and high temperature coefficients are found in dislocated regions on the wafers. A large spread of temperature coefficient is observed at regions with similar performance at 298 K. Reduced temperature sensitivity is found to be correlated with the increasing brick height and is exhibited by both wafers and…
Insights into Intrinsic Defects and the Incorporation of Na and K in the Cu2ZnSnSe4 Thin-Film Solar Cell Material from Hybrid-Functional Calculations
2016
We have performed density functional theory calculations using the HSE06 hybrid functional to investigate the energetics, atomic, and electronic structure of intrinsic defects as well as Na and K impurities in the kesterite structure of the Cu2ZnSnSe4 (CZTSe) solar cell material. We found that both Na and K atoms prefer to be incorporated into this material as substitutional defects in the Cu sublattice. At this site highly stable (Na–Na), (K–K), and (Na–K) dumbbells can form. While Na interstitial defects are stable in CZTSe, the formation of K interstitial defects is unlikely. In general, the calculated formation energies for Na-related defects are always lower compared to their K-related…
Comparative Theoretical Analysis of BN Nanotubes Doped with Al, P, Ga, As, In, and Sb
2013
SUMMARY AND CONCLUDING REMARKS We have performed large-scale first-principles calculations ofthe electronic structure of (5,5) boron nitride nanotubescontaining the following substitutional impurity atoms: Al, P,Ga, As, In, and Sb. Calculations have been performed using thetwo methods: (i) linear combination of atomic orbitals(LCAO) with the atomic-centered Gaussian-type functions asa basis set and (ii) linearized augmented cylindrical wave(LACW) accompanied with the local density functional andmuffin-tin approximations for the electronic potential. In arelatively good qualitative agreement, both methods predict lowformation energies and, thus, relative stability of point defectsthat are assoc…
Analytical description of solid particles kinematics due to a fluid flow and application to the depiction of characteristic kinematics in cold sprayi…
2017
Abstract In several multiphase flow applications such as fluidization, thermal spraying, atomization manufacturing and so on, the Newton's law is widely enacted to formulate the particle/fluid kinematic interaction and then to compute particles kinematics. This paper provides analytical solutions of the Newton's law in its time-dependent formulation or simplified formulation, the latter being a reduction of the time dependent problem into a spatial description of the particle motion. It was found that the velocity solution is strictly similar in both cases so that the simplified formulation is viable. The W_ 1 branch of the Lambert's function yields the analytical particle residence time an…
Modeling Stator Winding Inter-Turn Short Circuit Faults in PMSMs including Cross Effects
2020
Author's accepted manuscript. © 2020 IEEE. Personal use of this material is permitted. Permission from IEEE must be obtained for all other uses, in any current or future media, including reprinting/republishing this material for advertising or promotional purposes, creating new collective works, for resale or redistribution to servers or lists, or reuse of any copyrighted component of this work in other works. This paper presents a detailed analysis of stator winding inter-turn Short Circuit (ITSC) faults, taking the cross effects in the three phases of a permanent magnet synchronous motor (PMSM) into account by considering insulation degradation resistances. A PMSM with series coils in eac…
Custom measurement system for memristor characterisation
2021
Abstract A cheap, compact and customisable characterisation system for memristor devices, working between ± 10 V, is presented. SPICE (Simulation Program with Integrated Circuit Emphasis) simulations are performed to verify the circuit feasibility and a proper software is developed to drive the system. The potentiality of the realised system is tested by performing several electrical measurements on both Cu/HfO2/Pt memristors and two-terminals commercial devices.
A General Mathematical Formulation for the Determination of Differential Leakage Factors in Electrical Machines with Symmetrical and Asymmetrical Ful…
2018
This paper presents a simple and general mathematical formulation for the determination of the differential leakage factor for both symmetrical and asymmetrical full and dead-coil windings of electrical machines. The method can be applied to all multiphase windings and considers Gorges polygons in conjunction with masses geometry in order to find an easy and affordable way to compute the differential leakage factor, avoiding the adoption of traditional methods that refer to the Ossanna's infinite series, which has to be obviously truncated under the bound of a predetermined accuracy. Moreover, the method described in this paper allows the easy determination of both the minimum and maximum v…
Determination of differential leakage factors in electrical machines with non-symmetrical full and dead-coil windings
2017
In this paper Gorges polygons are used in conjunction with masses geometry to find an easy and affordable way to compute the differential leakage factor of non symmetrical full and dead coil winding. By following the traditional way, the use of the Ossanna's infinite series which has to be obviously truncated under the bound of a predetermined accuracy is mandatory. In the presented method no infinite series is instead required. An example is then shown and discussed to demonstrate practically the effectiveness of the proposed method.