Search results for "NEWA"
showing 10 items of 2491 documents
Survey on power increase of power by employment of PV reconfigurator
2015
This paper shows the performance of a PV system under shadow projection on PV panels. The reconfiguration techniques, employing a microprocessor-based system, modifies the layout of the PV plant by physically changing the connections among modules, in order to recover the loss of power due to the shadows. Different cases have been considered to evaluate the increase of power.
Uprating an Overhead Line. Italian TSO Applications for Integration of RES
2013
The increase of Renewable Energy Sources (RES) production units has caused significant changes in the electrical system configuration. The existing structural asset isn't adequate to dispatch these new power flows that, at same time, should be favorite by various TSOs in order to obtain incentives. The outage of primary substations on the grid and the increase of consumptions have caused growing load currents on existing overhead line. This paper, after introducing thermal resistant conductors and Dynamic Rating (DR) solutions, reports an applications used by TERNA Group S.p.A. (Italian TSO). These systems are already installed on lines and they are contributing to increase power flows than…
Distribution grid analysys through PSAT open source tools
2015
In this paper a study of an electrical distribution grid with presence of renewable energy sources performed using the Power System Analysis Tool is presented. The paper describes the load flow analysis of a real existing grid owned by the Italian DSO “ENEL Distribuzione SpA” and located in an urban area.
Green Data Centres providing ancillary services to power grid
2015
This work investigates the possibility for a Data Centre to provide services to the Grid. In particular, the paper simulates a sudden shift of frequency because of a power decrease and estimates how a real-life Data Centre can contribute the secondary frequency regulation.
Cogging torque comparison of Interior Permanent Magnet Synchronous Generators with different stator windings
2017
This paper presents the comparison between the cogging torques produced by four IPMSGs (Interior Permanent Magnet Synchronous Generators) with different stator winding configurations. More in detail, an IPMSG model, which is derived from a commercial geometry, is analyzed through means of a FEM (Finite Element Method) approach. Then, three more structures are determined and analyzed by adequately changing the number of stator slots of the basic IPMSG stator structure and by maintaining the same rotor configuration. From the obtained simulation results, the cogging torque components for each structure are determined and compared. From this comparison, it can be stated that the use of dissymm…
A circuit model of a 5kW fuel cell
2013
In the last few years, industrial research has been focused on renewable energy sources. Owing to combined heat-power generation option, fuel cells have attracted much interest for a wide variety of research areas. Household appliances are still the most promising applications. Fuel cell modeling is still a critical topic to focus on, affecting each stage of power system design. This paper describes an empirical method to model a proton exchange membrane fuel cell. The modeling approach is applied to a 5kW Nuvera PowerFlow fuel cell. A circuit model is proposed for further applications. PSPICE implementation is described and the parameters tuning procedure is discussed. Simulation and exper…
Grid synchronization of DC energy storage using Voltage Source Inverter with ZCD and PLL techniques
2015
To increase the penetration of renewable energy sources, a proper energy storage is required. In this context, there is a growing concern about the use of energy storage for overcoming the intermittency of renewable energy sources as well as in demand side management. In order to accomplish grid synchronization of energy storage, proper power conditioning devices are required. This paper analyses single phase grid synchronization of DC energy storage using MATLAB Simulink ® environment. The considered power conditioning device is a Voltage Source Inverter (VSI), which is controlled using two methods called (i) traditional Zero Crossing Detection (ZCD) technique and (ii) the phase detector b…
New solutions for prefabricated secondary substations in the view of sustainability
2016
The secondary substations will assume an important role as “smart nodes” of the smart grid. So in few years there will be a widespread dissemination on the territory of this apparatus. Consequently, great care have to be taken not only on safety issues, but also on the constructive methodology, in order to determine low environmental impact and decommissioning cost. This paper focuses on innovative solutions for the realization of prefabricated secondary substations, in the direction of sustainability. Innovative layout and enclosure topologies have been here taken into account. In particular, by considering that the substation concrete box is, at the same time, uneconomical and with strong…
A back to back method for the temperature rise test of prefabricated substations: A case study
2015
In this work a back to back method is presented which allows to develop heating tests of prefabricated secondary substations with a limited number of supplying equipment (an induction regulator and a capacitor bank). The proposed method makes use of the transformer tap changers to create a voltage difference on the medium voltage side. In this way, only an adjunctive low voltage supply is needed. With the proposed test system, the heating tests are developed on a 1000 kVA prefabricated substation. Thanks to the experimental tests, the class of enclosure of the substation and the operating temperature and resistance of the power transformers are determined, according to the recommendations o…
The strategies for the diffusion of EVs: Focus on Norway and Italy
2017
The goal of this work is to predict e-mobility trends which are essential for understanding the market and the infrastructure development over the next years. Nowadays among the many and different standards and rules there are two charging categories for electric vehicles: High power DC and AC charging modes. It will be interesting to see which technology will prevail in the next few years and if the charging mode option on a given EV affects its sales performance. This study presents the current e-mobility scenario in Norway and Italy, in particular analyzing: EV technical and commercial features, electric vehicle market related national incentive policies, technical and diffusion connecto…