Search results for "Note"
showing 10 items of 10709 documents
Wave Energy Assessment along Sicilian Coastline, Based on DEIM Point Absorber
2017
The use of renewable energy sources is one of the most relevant goals to be achieved in order to match the climate protection targets. As a case study, the paper shows the current electrical energy production by sources in the Sicilian context. Among the renewable energy sources, the paper investigates the wave energy potential along the Sicilian coasts, because of the favorable climate around the island. A point absorber is present in order to exploit this source. Two scenarios are presented, with two different levels of energy production.
Electronics for Application of Ion Beams in Nanoscience
2009
The breadth of ion-beam nanoscience methods discussed in the proceeding chapters implies that the control and readout systems also span a wide range of techniques. For many nanoscience and technology applications the need to process or characterise a batches of samples has lead to a convergence of data acquisition systems and control systems. This coupled with the development of high-performance lowcost computing over the past decades has lead to a progressive evolution in data acquisition technology. Historically, much of the electronics used in nanoscience and technology using ion beams is based on nuclear analogue pulse counting and spectrometry where NIM (Nuclear Instrumentation Modules…
Design and optimization of bonded patch repairs of laminated composite structures
2015
International audience; The present study proposes a method for design optimization of external patched repairs. The tensile behavior of notched specimens with patched repair was studied using finite element analysis and compared with experimental results. It was found that high stress concentrations along the transverse edges of circular patches and/or at the longitudinal edges of the hole leads to early damage initiation in the parent plate. The damage initiation site and its propagation depend on the patch in-plane stiffness. The optimal patch design can be characterized by a strength ratio R*. The overall design of the patch repair can be considered using a dimensionless design paramete…
Suitability of blends from virgin and reprocessed polylactide: performance and energy valorization kinetics
2018
[EN] A blending strategy of virgin and reprocessed polylactide may be postulated as an alternative to reduce the material cost at industrial level, and as a valorisation route to plastic waste management of production scraps. The performance of blends prepared from virgin polylactide and polylactide mechanically reprocessed up to two cycles (PLA-V/R) was assessed in terms of thermo-oxidative stability, morphology, viscoelasticity and thermal kinetics for energetic valorisation. PLA-V/R blends showed appropriate thermo-oxidative stability. The amorphous nature of polylactide was preserved after blending. The viscoelastic properties showed an increment of the mechanical blend effectiveness, w…
General model for boring tool optimization
2016
Optimizing a tool (and therefore those for boring) consist in improving its performance through maximizing the objective functions chosen by the designer and/or by user. In order to define and to implement the proposed objective functions, contribute numerous features and performance required by tool users. Incorporation of new features makes the cutting tool to be competitive in the market and to meet user requirements.
Use of finite element models for estimating thermal performance of façade-integrated solar thermal collectors
2016
Abstract Research on building-integrated solar thermal collectors is attracting increasingly more interest. Many efforts have been focused at the design level for obtaining specific building-orientated products, but there is a significant lack of standardised methods for evaluating how the efficiency of solar collectors changes when a wall is an integral part of the solar component itself. Generally speaking, experimental tests on integrated components are not easy to realise and are, in any case, expensive in terms of time and money. Physical and numerical methods can be utilised, but at the moment, there is no common approach. The present work addresses a method for the calculation of a b…
Low-Intensity Ultrasounds
2012
Ultrasonics, showing increasing use in the food industry for both the analysis and modification of food products, is a rapidly growing field of research. The sound ranges employed can be divided into high-frequency, low-energy diagnostic ultrasounds and low-frequency, high-energy power ultrasounds. The former is usually used as a nondestructive, rapid, easy-to-automate, and relatively inexpensive analytical technique for quality assurance and process control with particular reference to physicochemical properties, such as composition, structure, and physical state of foods. Nowadays, power ultrasound is considered to be an emerging and promising technology for industrial food processing. Th…
The Transverse Crack Tension test revisited
2016
Several problems arise when measuring the mode II interlaminar fracture toughness using a Transverse Crack Tension specimen; in particular, the fracture toughness depends on the geometry of the specimen and cannot be considered a material parameter. A preliminary experimental campaign was conducted on TCTs of different sizes but no fracture toughness was measured because the TCTs failed in an unacceptable way, invalidating the tests. A comprehensive numerical and experimental investigation is conducted to identify the main causes of this behaviour and a modification of the geometry of the specimen is proposed. It is believed that the obtained results represent a significant contribution in …
Fatigue life under non-Gaussian random loading from various models
2004
Fatigue test results on the 10HNAP steel under constant amplitude and random loading with non-Gaussian probability distribution function, zero mean value and wide-band frequency spectrum have been used to compare the life time estimation of the models proposed by Bannantine, Fatemi–Socie, Socie, Wang–Brown, Morel and Łagoda–Macha. Except the Morel proposal which accumulates damage step by step with a proper ethodology, all the other models use a cycle counting method. The rainflow algorithm is used to extract cycles from random histories of damage parameters in time domain. In the last model, where a strain energy density parameter is employed, additionally spectral method is evaluated for …
Selective recovery of gold from electronic waste using 3D-printed scavenger
2017
Around 10% of the worldwide annual production of gold is used for manufacturing of electronic devices. According to the European Commission, waste electric and electronic equipment is the fastest growing waste stream in the European Union. This has generated the need for an effective method to recover gold from electronic waste. Here, we report a simple, effective, and highly selective nylon-12-based three-dimensional (3D)-printed scavenger objects for gold recovery directly from an aqua regia extract of a printed circuit board waste. Using the easy to handle and reusable 3D-printed meshes or columns, gold can be selectively captured both in a batch and continuous flow processes by dipping …