Search results for "OTU"
showing 10 items of 2539 documents
Effect of a new amido‐imidazolium compound as a clay modifier on properties of polypropylene composites
2021
Halloysite nanotubes (HNT) and montmorillonite (Mt) were modified by a novel, dicarboxylic fatty acid substituted amido-imidazolium chloride. It was found that the modification process of the clays by the imidazolium compound improved their dispersion in the polymer matrix, while HNT were a more beneficial filler of PP than Mt. PP/imidazolium modified HNT composites (PP/HNT-M) showed significant increase in thermo-oxidative stability, flexibility, and toughness, combined with a slight reduction in stiffness, as well as a lack of changes in crystallinity and strength, compared with neat PP. These effects were not observed for PP/Mt composites. The formation of strong interactions between the…
Cyclic moisture sorption and its effects on the thermomechanical properties of epoxy and epoxy/MWCNT nanocomposite
2019
The aim of this work was to reveal the moisture absorption&ndash
Recent Progress in the Development of Composite Membranes Based on Polybenzimidazole for High Temperature Proton Exchange Membrane (PEM) Fuel Cell Ap…
2020
[EN] The rapid increasing of the population in combination with the emergence of new energy-consuming technologies has risen worldwide total energy consumption towards unprecedent values. Furthermore, fossil fuel reserves are running out very quickly and the polluting greenhouse gases emitted during their utilization need to be reduced. In this scenario, a few alternative energy sources have been proposed and, among these, proton exchange membrane (PEM) fuel cells are promising. Recently, polybenzimidazole-based polymers, featuring high chemical and thermal stability, in combination with fillers that can regulate the proton mobility, have attracted tremendous attention for their roles as PE…
Electronic and optical properties of carbon nanotubes under pure bending
2010
The high aspect ratio of carbon nanotubes makes them prone to bending. To know how bending affects the tubes is therefore crucial for tube identification and for electrical component design. Very few studies, however, have investigated tubes under small bending well below the buckling limit, because of technical problems due to broken translational symmetry. In this Brief Report a cost-effective and exact modeling of singe-walled nanotubes under such small bending is enabled by revised periodic boundary conditions, combined with density-functional tight-binding. The resulting, bending-induced changes in electronic and optical properties fall in clear chirality-dependent trend families. Whil…
Electronic Properties of Thermal Oxides on Ti and Their Influence on Impedance and Photoelectrochemical Behavior of TiO2 Nanotubes
2017
Thermal oxidation of titaniumwas carried out at 350◦C, 450◦C, and 550◦C for 2 h or 12 h.X-rayDiffraction and Raman Spectroscopy suggest that the thermal oxides are scarcely crystallinewhen the annealing temperature is low, while both anatase and rutile are present for high annealing temperature and time. Photoelectrochemical measurements allowed estimation of a bandgap decreasing from 3.35 eV to 3.15 eV with increasing annealing temperature. The impedance spectra confirmed the formation of n-type semiconductors, with an impedance strongly decreasing on going from a reverse bias toward a forward bias regime. TiO2 nanotubes grown by anodizing Ti in NH4F and water containing ethylene glycol so…
Pickering Emulsions Based on Wax and Halloysite Nanotubes: An Ecofriendly Protocol for the Treatment of Archeological Woods
2020
A novel green protocol for the consolidation and protection of waterlogged archeological woods with wax microparticles has been designed. First, we focused on the development of halloysite nanotubes (HNTs) based Pickering emulsions using wax as the inner phase of the oil-in-water droplets. The optimization of the preparation strategy was supported by both optical microscopy and scanning electron microscopy, which allowed us to show the morphological features of the prepared hybrid systems and their structural properties, i.e., the distribution of the clay at the interface. Also, the dependence of the overall dimensions of the prepared systems on the halloysite content was demonstrated. Micr…
Morphology and structure of electrospun CoFe2O4/multi-wall carbon nanotubes composite nanofibers
2010
CoFe2O4/multiwall carbon nanotubes (MWCNTs) composite nanofibers were produced by electrospinning a dispersion of MWCNTs in a solution of polyvinylpyrrolidone, iron(III) nitrate nonahydrate, cobalt (II) acetate tetrahydrate, absolute ethanol and H2O. Microstructure was examined by scanning electron microscopy (SEM) and high resolution transmission electron microscopy (HR-TEM). Thermal behaviour was studied by thermogravimetry and differential thermal analysis (TG-DTA) and phase analysis of calcined fibers was performed by X-ray diffraction (XRD). Upon thermal treatment at 450 °C defect-free, randomly oriented composite fibers having a mean diameter of 60 ± 10 nm were obtained. The results s…
Antimicrobial Bilayer Nanocomposites Based on the Incorporation of As-Synthetized Hollow Zinc Oxide Nanotubes
2020
© 2020 by the authors.
Rheological Percolation Threshold in High-Viscosity Polymer/CNTs Nanocomposites
2017
AbstractPolystyrene (PS)/multi-walled carbon nanotubes (CNT) nanocomposites have been prepared through melt mixing processing aiming at obtaining a uniform and homogeneous dispersion of the used nanoparticles within the polymeric matrix. Optical and scanning electron microscopy has been employed to determine the dispersion and distribution of CNTs at different length scales. Furthermore, the linear viscoelastic behavior of formulated nanocomposites has been deeply investigated. As a result of CNTs added, the nanocomposites experience a transition from liquid-like to solid-like rheological behavior, and a disappearance of relaxation processes at low frequency can be noticed. By plotting G’ v…
Carbon nanotubes and organic solar cells
2012
The use of carbon nanotubes in photovoltaics is still challenging due to different issues connected to their synthesis, purification, functionalization, processing and device integration. From this perspective at first we review on selected contributions dealing with the above issues; then we focus on the advantages and limitations of carbon nanotubes for the development of organic solar cells.