Search results for "On resistance"
showing 10 items of 61 documents
Process parameters and surface treatment effects on the mechanical and corrosion resistance properties of Ti6Al4V components produced by laser powder…
2023
Laser powder bed fusion is one of the additive manufacturing technologies which has developed more rapidly in recent years as it enables the production of very complex geometries. Titanium alloys are among the most popular materials in the aerospace industry thanks to excellent mechanical and corrosion resistance. The corrosion behavior and mechanical properties of samples made of Ti6Al4V and characterized by the geometrical features typical of brackets were investigated taking into account the effects of process parameters on porosity and microstructure. A comparison between the corrosion resistance of samples with complex geometry (3D) and specimens characterized by simple geometry (FLAT)…
CORROSION RESISTANCE OF DIFFERENT STAINLESS STEEL GRADES IN FOOD AND BEVERAGE INDUSTRY
2020
MoSi2 laser cladding—a comparison between two experimental procedures: Mo–Si online combination and direct use of MoSi2
2001
International audience; There are very strong interests in developing low density advanced material systems for service at temperatures up to 1300°C. These materials should mainly have moderate fracture toughness at low and intermediate temperatures and should exhibit oxidation resistant behaviour. The intermetallic compound, MoSi2 has been considered to be an attractive candidate due to its melting point (2030°C) and excellent oxidation resistance at high temperatures. In this paper, we compare the results obtained with two different techniques for laser cladding, one using an online combination between Mo and Si powders, the second using direct injection of the MoSi2 powder.
Atmospheric dry deposition processes of particles on urban and suburban surfaces: Modelling and validation works
2019
Abstract Dry deposition process is one of the important pathways for the removal of particles from atmosphere. It is the result of a combination of different environmental and physical factors as atmospheric conditions, particle properties, characteristics of the canopy. For this latter factor, urban canopy represents unevenly combinations of different types of surface elements that increases the complexity of deposition process phenomena. Therefore, particle dry deposition on urban surfaces is not easy to configure and, although empirical or semi-empirical models in literature have been developed to address this aspect, there is not standardized and commonly accepted criteria, especially f…
Why have consumers opposed, postponed, and rejected Innovations during a pandemic? A Study of mobile payment Innovations
2021
The highly infectious nature of the COVID-19 virus has made the use of contactless payment methods a health exigency. Yet, consumers are resisting using mobile payments (m-payments) during the pandemic, a confounding behavior that needs to be better understood. The present study explicates this behavior by examining consumer resistance to m-payments during the COVID-19 pandemic. In addition, it provides more granular findings by measuring three levels of resistance/non-adoption, namely, postponement, opposition, and rejection. In this way, the study adds depth to the literature, which has largely examined resistance at an aggregate level to yield generic findings. Toward this end, the study…
Laser Cladding of TiC for Better Titanium Components
2011
Pure commercial titanium is widely used because of its high corrosion resistance and lower cost compared with other titanium alloys, in particular when there is no high wear requirements. Nevertheless, the wear resistance is poor and surface damage usually occurs in areas under contact loadings. Laser cladding is a suitable technique for manufacturing precise and defect free coatings of a dissimilar material with higher wear and corrosion resistance. In this work a good understanding of laser metal deposition mechanisms allowed to obtain defect free coatings of Ti6Al4V and TiC metal matrix composite (MMC) using a flash lamp pumped Nd:YAG laser of 1 kW. A complete investigation of the proces…
Impact of Superfinish Turning on Surface Integrity of Pure Copper
2011
Abstract The presented study deals with comprehension of relationships between machining cutting conditions and physical-chemical properties linked with surface integrity. A multi-physics model is presented to calculate residual stress, temperature and dislocation fields in the machined material. This model includes both thermal-mechanical, structural evolution and dynamic recristallisation approaches. The model was applied to pure copper after superfinish turning. Good agreement was found between numerical values and experimental ones. This paper also presents a work on the impact of mechanical and microstructural changes induced by machining on the electrochemical behaviour and corrosion …
Influence of cutting process mechanics on surface integrity and electrochemical behavior of OFHC copper
2014
The authors gratefully acknowledge the support received from IC ARTS and CEA Valduc; International audience; Superfinishing machining has a particular impact on cutting mechanics, surface integrity and local electrochemical behavior. In fact, material removal during this process induces geometrical, mechanical and micro-structural modifications in the machined surface and sub-surface. However, a conventional 3D cutting process is still complex to study in terms of analytical/numerical modeling and experimental process monitoring. So, researchers are wondering if a less intricate configuration such as orthogonal cutting would be able to provide information about surface integrity as close as…
Biochar Particles Obtained from Agricultural Carob Waste as a Suitable Filler for Sustainable Biocomposite Formulations
2022
In the context of sustainable and circular economy, the recovery of biowaste for sustainable biocomposites formulation is a challenging issue. The aim of this work is to give a new life to agricultural carob waste after glucose extraction carried out by a local factory for carob candy production. A pyrolysis process was carried out on bio-waste to produce biofuel and, later, the solid residual fraction of pyrolysis process was used as interesting filler for biocomposites production. In this work, biochar particles (BC) as a pyrolysis product, after fuels recovery of organic biowaste, specifically, pyrolyzed carobs after glucose extraction, were added on poly(butylene-adipate-co-terephthalat…