Search results for "PHOTOELASTICITY"
showing 10 items of 41 documents
Numerical simulations and experimental measurements of the stress intensity factor in perforated plates
2008
A numerical procedure, which combines two hybrid finite element formulations, was developed to analyse the stress intensity factors in cracked perforated plates with a periodic distribution of holes and square representative volume elements. The accuracy of the method in predicting the stress intensity factor was verified by a comparison with experimental measurements, carried out by a photoelasticity method, and by commercial finite element software. Several simulations were executed by varying both the crack length and the hole diameters, and the effects of the holes on the stress intensity factor are illustrated. The method shows high accuracy and efficiency, as small differences were ob…
RGB Photoelasticity: Review and Improvements
2010
: This paper considers the main developments of RGB photoelasticity with reference to the maximum measurable retardation. In this paper, a new procedure based on the standard error function evaluated on a subset of the calibration array is also proposed and experimentally tested. The experiments show that the filament lamp makes it possible to find retardations until approximately 4 fringe orders while the fluorescent lamp makes it possible to determine higher fringe orders (12 fringe orders in this paper) owing to the discrete spectrum of the source. The paper shows that, by using the incandescent lamp, the primary limiting factor is the lack of modulation of the R, G and B signals wherea…
A single hologram technique for the determination of absolute retardations in holographic photoelasticity
1975
A method for the determination of the absolute retardations families in photoelasticity. The method, which use real-time holographic interferometry, requires only one hologram for the observation of the absolute retardations over the whole model. This is achieved by viewing in the reconstruction process the loaded model through a polarizer. Where the polarization direction is parallel to one of the principal stresses, only the corresponding family of absolute retardations is observed. As an example of application the absolute retardations and stresses in a deep beam centrally loaded are determined.
The influence of the quarter wave plates in automated photoelasticity
2002
During the last decades, several methods have been proposed to automate photoelastic analyses. Some procedures are based on the circularly polarised light by using quarter wave plates. However, quarter wave plates are typically matched for a specific wavelength, and an error is introduced at different wavelengths. The error of quarter wave plates affects the measurement of isochromatic and isoclinic data. In this paper, the influence of the errors of quarter wave plates in some of the most common automated photoelastic methods is reviewed. The errors in the photoelastic data are given and the procedures to reduce, or eliminate, them are also suggested.
Synchronization of Two Photoelastic Light Modulators to Obtain Müeller Matrix
2013
We report a method for the temporal synchronization of two photoelastic light modulators. For synchronizing, we used the transistor-transistor logic output signals from each modulator, which contain the information on the light polarization. These signals were introduced in a phase-detector circuit, which provided the phase difference value between both modulators. Three optical devices were used to test the synchronization method proposed: a polarizer, a half-wave, and a quarter-wave retarder plate. The value of each of the elements of the Mueller matrix for these devices was obtained using the method of the 36 measurements. The results show a high correlation between the theoretical and e…
Automatic photoelastic methods for the analysis of Membrane residual stresses in glass
2014
Photoelastic Analysis of Partially Occluded Objects With an Integral-Imaging Polariscope
2014
Polariscopes are the basic instruments used for the analysis of the stress state of transparent materials. Polarized light passing through a 3D object carries the integrated effect of the stress field along the light path. Therefore, conventional polariscopes are not able to discern the stress state of objects involving multiple plates with mutual occlusions. In this paper we propose a novel experimental system for three-dimensional stress analysis based on the combination of a polariscope and Synthetic Aperture Integral Imaging technique. Experimental results show the system's ability to recover the information of the stress distribution of a set of plates located at different depths havin…
Photoelastic stress analysis assisted evaluation of fracture toughness in hydrothermally aged epoxies
2014
The present work has investigated the fracture toughness of a model DGEBA epoxy system subject to Hidro-Thermal aging. A Photoelastic Stress Analysis technique has been implemented, showing the evolution of stresses arising throughout the water uptake process due to the non-uniform swelling of the material. Gravimetric and Dynamic Mechanical Thermal Analyses have further complemented the characterization, showing the onset of plasticization effects with aging. The correlation of all previous characterizations has allowed to conclude that an increase of KIC fracture toughness is obtained at the fully saturated condition. In particular Photoelasticity has also revealed the onset of relevant s…
Review of photoelastic image analysis applied to structural birefringent materials: glass and polymers
2015
Photoelasticity is particularly suitable for the analysis of the stress state in structural materials that are transparent and birefringent. Some techniques of digital photoelasticity (phase shifting and RGB) are applied to the analysis of stress field in two classes of structural materials. The first one consists of tempered glasses, such as those used in the automotive and architectural fields. The second one consists of thermoset polymers, typically used as matrices in fiber reinforced plastic structural composites. The birefringence of such resins is, in particular, exploited to investigate the development of swelling stresses and changes in fracture toughness as induced by water uptake…