Search results for "PLASTICS"
showing 10 items of 2724 documents
Thermal properties of e-beam cured epoxy/thermoplastic matrices for advanced composite materials
2007
The aim of this work is to investigate the possibility to improve the thermal behaviour of epoxy based systems, cured by ionizing radiation, in order to produce matrices for advanced carbon fibres composites. Blends of two epoxy monomers, difunctional and trifunctional, have been polymerized by e-beam irradiation and the dynamic mechanical thermal properties have been investigated. The increase of the concentration of the trifunctional epoxy monomer in the blend causes a marked increase of the Tg, but strongly decreases the reactivity. Subsequently, blends of the same epoxy monomers with a high Tg thermoplastic toughening agent have been considered and their reactivity and the thermal prope…
Synthesis of reactive hyperbranched and star-like polyethers and their use for toughening of vinylester–urethane hybrid resins
2004
A vinylester – urethane hybrid resin (VEUH) was toughened by adding various vinyl-functionalized branched polyethers in 10 and 20 wt%. Two sets of hyperbranched polymers (HBPs) with different branching density were compared with a set of six-arm star polymers. Besides the architecture, the polymers also varied in their characteristics (molecular mass and mass distribution, vinyl/hydroxy ratio). The morphology of the modified VEUH was studied by dynamic-mechanical thermal analysis (DMTA), transmission (TEM) and scanning electron microscopy (SEM). The toughness was characterized by the fracture energy ðGcÞ determined on compact tension specimens at room temperature. It was established that th…
Effects of organoclay on morphology and properties of nanocomposites based on LDPE/PA-6 blends without and with SEBS-g-MA compatibilizer
2009
LDPE/PA-6 blends (75/25 wt/wt) were added with SEBS-g-MA (S) and/or an organoclay (20A) using different compounding sequences and the morphology and the properties of the blends or composites were investigated. An XRD study of the nanocomposites with pure polymers showed that 20A is intercalated by LDPE or PA-6 chains, whereas it is exfoliated by S if the clay concentration does not exceed 10 wt%. The SEM investigation showed that both S and 20A behave as efficient emulsifying agents for the LDPE/PA-6 blends. However, their effect on the mechanical properties was found to be opposite: S enhanced toughness but lowered the stiffness, whereas 20A improved the elastic modulus but impaired the i…
Characterization of ultra-high-molecular-weight polyethylene (UHMWPE) modified by ion implantation
2004
Abstract Surface modification of ultra high molecular weight polyethylene (UHMWPE) is induced by ion implantation of different ions at 300 keV energy. The aim of this work was the chemical, physical and mechanical characterization of the modified material in order to know deep inside about the effect of the ion beam upon the polymer. The irradiated surfaces are investigated by Raman spectroscopy, infrared absorption and micro-hardness analysis, scanning electron microscopy. Pin on disc measurements valuated the wear of the UHMWPE against a stainless steel probe; wear resistance increases of about 76% after the ion implantation. This result can be attributed to the ion bombardment inducing a…
Time–carbonyl groups equivalence in photo-oxidative aging of virgin/recycled polymer blends
2004
AbstractThe photo-oxidation behaviour of polymers is strongly dependent on the initial amount of carbonyl groups along the chains. The growing use of recycled post-consumer polymers coming from products used outdoors and then photo-oxidised, both pure and blended with the same virgin polymer, gives rise to an unpredictable behaviour of weathering resistance of products made with these materials. The present work shows that the carbonyl group–exposure time curves can be shifted along the time axis to give a single generalised master plot. It is then possible to predict the formation of the new carbonyl groups by knowing only the initial amount of the same carbonyl groups. The same shift fact…
LARGE DEFORMATION CREEP BEHAVIOR OF A SOLID POLYMER.
1981
Abstract The effect of loading rate and strain on the creep behavior after sample yielding has been studied in previous communications (14–15) for Mylar in tension and for Lexan in compression. In this work the creep behavior of Lexan samples previously elongated is considered both in tension and in compression. A procedure which collects all the data independently of both loading rate and initial creep strain is proposed.
Influence of“controlled processing conditions” on the solidification of iPP, PET and PA6
2002
In this work reliable experimental data for three semicrystalline polymers (iPP, PA6, PET) crystallised under pressure and high cooling rates are supplied. These results were achieved on the basis of a model experiment where drastic controlled solidification conditions are applied. The final objective was to quantify the effect of two typical operating conditions (pressure and cooling rate) on the final properties and morphology of the obtained product. The influence of processing conditions on some macroscopically relevant properties, such as density and micro hardness is stressed, together with the influence of processing conditions on the product morphology, investigated by means of Wide…
The use of the indentation test for studying the solidification behaviour of different semicrystalline polymers during injection moulding
2005
Summary: An in-line method for monitoring the solid-ificationprocess during injection molding of semicrystallinepolymers (demonstrated previously in J. Appl. Polym. Sci.2003, 89, 3713) is based on a simple device, where anadditional ejector pin is pushed on the injection molded partatdifferenttimesduringthesolidificationphase.The‘inden-tation depth profile’, i.e., residual deformation as a functionoftime,wasobtainedandallowedtodeterminetheevolutionof the solidification front in the mold as a function of thecooling time. The present work shows the reliability andthe powerfulness of the aforementioned method for a largevariety of different semicrystalline polymers (PET, PBT,polyamide-6 PA6, isota…
Deformation recovery behavior of a solid polymer after tensile yielding
1984
In this work the deformation recovery behavior of an amorphous polymer after large tensile deformation is studied at different temperatures. The effect of three parameters other than temperature has been pointed out in previous works (1–3).
Deformation recovery behaviour of a solid polymer after tensile yielding
1987
In this work the deformation recovery behavior of an amorphous polymer after large tensile deformation is studied at different temperatures. The effect of three parameters other than temperature has been pointed out in previous works (1–3). The data here presented indicate that the influence of all parameters, including temperature, on recovery behavior can be related to the residual stress, σ *, at the beginning of recovery test. This suggests to plot the recovery versus time curves, relative to different sets of parameters including temperature, by means of the same normalizing groups which were adopted in (2), thus shifting all curves towards a single master curve.