Search results for "PLASTICS"
showing 10 items of 2724 documents
Amount, composition, and spatial distribution of floating macro litter along fixed trans-border transects in the Mediterranean basin
2018
Marine litter is a major source of pollution in the Mediterranean basin, but despite legislative requirements, scant information is available for the ongoing assessment of this threat. Using higher size classes as proxy for litter distribution, this study gave a synoptic estimation of the amount, composition, and distribution of floating macro-litter in the Mediterranean. The average amount of macro-litter was in a range of 2-5 items/km2, with the highest in the Adriatic basin. Seasonal patterns were present in almost all study areas and were significant in the Ligurian Sea, Sardinian-Balearic basin, and Central Tyrrhenian Sea. Plastic accounted for > 80% of litter in all areas and seaso…
On the use of Persian gum for the development of antiviral edible coatings against murine norovirus of interest in blueberries.
2021
In the last decades, berries have been identified as important vehicles for the transmission of foodborne viruses and different strategies are being explored to eliminate or reduce viral contamination in these fruits. The aim of this work was to develop novel edible coatings with antiviral properties for inactivating and reducing murine norovirus (MNV). Firstly, the effect of gelatin (G) addition on Persian gum (PG) films was studied in terms of microstructural, mechanical, optical, and water barrier properties. The following PG:G ratios were considered: 100:0, 75:25, 50:50, 25:75, and 0:100. Microstructure analysis revealed the compatibility of both hydrocolloids since no phase separation …
Can phthalates move into the eggs of the loggerhead sea turtle Caretta caretta? The case of the nests on the Linosa Island in the Mediterranean Sea
2021
During the monitoring of Caretta caretta nests on the island of Linosa, 30 unhatched eggs from four nests were collected to study the presence of phthalates in their three components (shell, yolk, and albumen). Four phthalates, namely diethyl (DEP), dibutyl (DBP), di-(2-ethylhexyl) (DEHP), and dioctyl (DOTP) phthalic acid esters (PAE), which are widely used as additives in plastics, were detected in all egg components. The most frequently found phthalate was DBP, followed by DEHP in eggshell and yolk. Dimethyl- (DMP) and butylbenzyl-phthalate (BBP) were below the limits of detection for all samples. The high total phthalate recorded in the yolk suggests that contamination could arise by vit…
Failure maps to assess bearing performances of glass composite laminates
2018
Aim of this article is the assessment of the bearing mechanical performances of pin-loaded glass laminates as function of their geometrical configuration. To this concern, 32 specimens having different hole diameter (D), laminate width (W), and hole center to laminate free edge distance (E) have been tested under bearing conditions. The maximum bearing stress and the stress-displacement curves were analyzed as function both of hole to laminate free edge distance E and hole diameter D. Moreover, an experimental 2D failure map was created by placing the experimental results (i.e., the kind of failure mechanism occurred for each geometrical configuration) in the plane E/D versus W/D ratios. In…
Mechatronic Design for an Extrusion-Based Additive Manufacturing Machine
2017
3D printers, especially in the implementation of innovative extrusion processes which do not have a long history of development, are often built by adapting mechanical designs, drives and controls previously developed for generic machine tools. This is done through a process of choice and integration which is based principally on empirical criteria and taking into account separately the different aspects and parameters. Hereafter, we present an integrated mechatronic approach which has been adopted to design from the scratch a machine to implement the innovative metal injection moulding (MIM) technology. Its extrusion rate involves the adaptation of the generated trajectories and consequent…
On the Heuristic Procedure to Determine Processing Parameters in Additive Manufacturing Based on Materials Extrusion
2020
We present a heuristic procedure for determining key processing parameters (PPs) in materials-extrusion-based additive manufacturing processes. The concept relies on a design-of-experiment approach and consists of eleven &ldquo
An Additive Model to Predict the Rheological and Mechanical Properties of Polypropylene Blends Made by Virgin and Reprocessed Components
2021
In this work, an additive model for the prediction of the rheological and mechanical properties of monopolymer blends made by virgin and reprocessed components is proposed. A polypropylene sample has been reprocessed more times in an extruder and monopolymer blends have been prepared by simulating an industrial process. The scraps are exposed to regrinding and are melt reprocessed before mixing with the virgin polymer. The reprocessed polymer is, then, subjected to some thermomechanical degradation. Rheological and mechanical experimental data have been compared with the theoretical predictions. The results obtained showed that the values of this simple additive model are a very good fit fo…
Application of a compositional rotatable plan in modeling the propylene content in a vinyl chloride/propylene copolymer
2019
Abstract Using a fractional rotatable plan, the effect of five input parameters of the conduct of the copolymerization process on the amount of propylene built into the copolymer, obtained as a result of free radical suspension copolymerization of vinyl chloride with propylene in a batch suspension polymerization reactor, was analyzed. Using the results obtained, the analysis of variance was carried out and the influence of particular factors and their interactions on the product properties was determined. Thus, it was determined that the greatest influence on the amount of the incorporated propylene in the copolymer is exerted by the amount of propylene introduced into the system, while th…
Dissimilar titanium/aluminum friction stir welding lap joints by experiments and numerical simulation
2016
Dissimilar lap joints were produced by friction stir welding (FSW) out of Ti6Al4V titanium alloy and AA2024 aluminum alloy sheets. The joints, welded with varying tool rotation and feed rate, were studied by analyzing the maximum shear strength, Vickers microhardness and optical observations. A dedicated numerical model, able to take into account the presence of the two different alloys, was used to highlight the effects of the process parameters on temperature distribution, strain distribution, and material flow. The combined analysis of experimental measurements and numerical predictions allowed explaining the effects of tool rotation and feed rate on the material flow. It was found that …
Ultrasonic Welding of PBT-GF30 (70% Polybutylene Terephthalate + 30% Fiber Glass) and Expanded Polytetrafluoroethylene (e-PTFE)
2021
The ultrasonic welding of polymeric materials is one of the methods often used in practice. However, each couple of material subjected to ultrasonic welding is characterized by different values of technological parameters. Therefore, the main objective of the research presented in this paper is to optimize the parameters for the ultrasonic welding of two materials, namely PBT-GF30 (70% polybutylene terephthalate + 30% fiber glass) and expanded polytetrafluoroethylene (e-PTFE). In this sense, the research was carried out considering a plate-type part made of PBT-GF30, which had a thickness of 2.1 mm, and a membrane-type part made of e-PTFE, with a thickness of 0.3 mm. The condition imposed o…