Search results for "POWER ELECTRONICS"
showing 10 items of 80 documents
A Permanent Magnet Linear Generator for the Enhancement of the Reliability of a Wave Energy Conversion System
2019
In this paper, a linear generator for a highly reliable Wave Energy Conversion system is designed and tested. In order to store energy, the system is able to produce hydrogen The Wave Energy Conversion System consists of an electrical linear generator, a power conversion system and a sea-water electrolyzer. A small scale prototype of the system has been designed and built. The design is oriented to the enhancement of the system robustness and reliability and a Failure Mode and Effects and Criticality Analysis (FMECA) has been used. In order to guarantee an easy extension of the power capability of the marine plant, a modular architecture of the system has been adopted. The design strategy i…
Guidelines proposal for a good and durable WEC design
2017
In this paper, preliminarily a proposal for design guidelines for a “good” design of wave energy converter is presented and successively a small scale prototype of a wave energy converter including the buoyant electrical generator, the power electronics equipment and a sea water electrolyzer is designed on the basis of these guidelines and presented.
A wireless battery charger architecture for consumer electronics
2012
In this paper, an innovative design of a wireless battery charger for portable electronic devices is proposed. The wireless power transfer is implemented through the magnetic coupling between a power transmitter, which is connected to the grid, and a power receiver, which is integrated inside the load device. An innovative receiver architecture which heavily improves the power conversion efficiency is presented. The proposed solution is standard compliant and suitable for IC implementation. A comparison between a conventional and the proposed receiver architectures is carried out by SPICE simulations. As shown by simulation results, a power efficiency increase by 40% is provided by the prop…
Physically-consistent parameterization in the modeling of solar photovoltaic devices
2011
This research tests the standard one-diode model of a crystalline-Si photovoltaic cell, focusing on the physical accuracy. In particular, the (apparent) shunt resistance and the diode ideality factor are studied. Current-voltage characteristics of illuminated crystalline-Si photovoltaic modules are analyzed, and some limits of applicability of the standard model are given. Typical values of the ideality factor for crystalline-Si devices are derived from own experimental data as well as from recently published literature. It is shown that the contribution of the apparent shunt resistance is only significant for cell voltages below about 0.45 V, and depends on irradiance. This result is consi…
Design and Modeling of an Interleaving Boost Converter with Quasi-Saturated Inductors for Electric Vehicles
2020
This paper is focused on the analysis and modeling of DC-DC boost converters in interleaving configuration exploiting inductors in the quasi-saturation region. The converter is designed to optimize the power density by minimizing the size of the inductors. A simulation study for electric vehicle applications is conducted analyzing the effects of duty cycle and temperature variation on the ripple of the input current giving, moreover, information on the performances and dynamics of the converter for further implementation and optimizations.
A digital control technique for high-performances DC-DC converters
2008
Experimental test on a fuel cell-supercapacitor hybrid power supply for a digital still camera
2009
Experimental test of the performances of a photovoltaic modules model
2015
In this paper, a measurement-based modeling technique for PV panels oriented to power electronics design is proposed. The proposed modelling approach aims at an accurate modeling of the whole PV curve and not only around a few remarkable points. The proposed approach is based on an experimental characterization of the module under test. In fact, the incompleteness of manufacturers' data and the knowledge of physical parameters are the main source of inaccuracy in existing modelling approaches. The proposed approach is applied to a four lumped parameters model of a Conergy E215P solar module. Tests are performed under natural light. The parameter identification procedure is described in deta…
Development of bidirectional dc-dc converters for hybrid power sources - Final Report
2018
A Bidirectional Isolated Full-Bridge Converter was designed, prototyped and tested. The device is intended to interface a Bank of Supercapacitors with a battery-powered bus, in order to boost the capability of supplying large power peaks. The converter was based on the Isolated Dual Active Bridge configuration. When driven by an external control voltage, it is capable of generating in both directions a train of current pulses, with 2kW peak power, for any battery voltage in the range 24-32V and for any supercapacitor voltage in the range 35-70V. Worst-case battery current was 70A. Pulse duration was 100ms with 50% duty cycle and 1 ms rise time.
Overview of Power Electronic Switches: A Summary of the Past, State-of-the-Art and Illumination of the Future.
2020
As the need for green and effective utilization of energy continues to grow, the advancements in the energy and power electronics industry are constantly driven by this need, as both industries are intertwined for obvious reasons. The developments in the power electronics industry has over the years hinged on the progress of the semiconductor device industry. The semiconductor device industry could be said to be on the edge of a turn into a new era, a paradigm shift from the conventional silicon devices to the wide band gap semiconductor technologies. While a lot of work is being done in research and manufacturing sectors, it is important to look back at the past, evaluate the current progr…