Search results for "Pellet"
showing 10 items of 129 documents
Mix design and mechanical performance of geopolymeric binders and mortars using biomass fly ash and alkaline effluent from paper-pulp industry
2019
Abstract This work investigates the use of biomass fly ash (BFA) and an alkaline effluent (AEF), both generated from the Kraft pulp industry, in the preparation of geopolymeric binders and mortars for construction applications. BFA replaced the metakaolin (MK) while the AEF substituted the distilled water used to dissolve NaOH pellets. The mix design aims to maximize the amount of both the wastes and to optimize the materials properties, such as workability and mechanical performance. At the same time, also the environmental impact decreases enhancing the materials' sustainability and facilitating the circular economy. For the previously optimized BFA/MK ratio (70/30 wt.%) several NaOH/Na2S…
Validation of a method for the determination of boron in ceramic materials by X-ray fluorescence spectrometry
2000
Abstract A method is proposed for boron determination in ceramic materials, boracic raw materials and ceramics frits of different compositions by wavelength dispersive X-ray fluorescence technique. The instrumental conditions were studied and the sample preparation procedures were optimized. The reference method used was the potentiometric titration of mannitol–boric complex acid and the technique was optimized for the determination of B 2 O 3 in each of the materials used. The samples for XRF determination were obtained as pellets and as glass discs. For the pellets different binders were studied, such as mannitol and cellullose for the samples of raw materials, and polyvinylpirrolidone an…
Programmable proximity aperture lithography with MeV ion beams
2008
A novel MeV ion beam programmable proximity aperture lithography system has been constructed at the Accelerator Laboratory of the University of Jyvaskyla, Finland. This facility can be used to fabricate three dimensional microstructures in thick (<100μm) polymer resist such as polymethylmethacrylate. In this method, MeV ion beams from the 1.7 MV pelletron and K130 cyclotron accelerators are collimated to a beam spot of rectangular shape. This shape is defined by a computer-controlled aperture made of a pair of L-shaped Ta blades which are in close proximity to the sample to minimize the penumbra broadening. Here the authors report on development of the system, the controlling software, the …
Thermoluminescence study of irradiated lithium orthosilicate
1998
Abstract The thermoluminescental investigations of neutron and gamma irradiated lithium orthosilicate pellets were carried out. It has been shown that the addition of Cr 3+ and Fe 3+ ions with the total concentration up to 2.0 wt.% during preparation of lithium orthosilicate pellets, significantly reduces the formation of radiation defects in irradiated matrix. This phenomena can be explained by the reducing of the formation of primary radiation defects during irradiation due to stimulating the recombination processes by the ions of impurities. Several ion concentration combinations were studied. The thermoluminescental investigations of fast neutron irradiated lithium orthosilicate pellets…
Tracer-Encapsulated Solid Pellet (TESPEL) injection system for the TJ-II stellarator
2016
A tracer-encapsulated solid pellet (TESPEL) injection system for the TJ-II stellarator was recently developed. In order to reduce the time and cost for the development, we combined a TESPEL injector provided by National Institute for Fusion Science with an existing TJ-II cryogenic pellet injection system. Consequently, the TESPEL injection into the TJ-II plasma was successfully achieved, which was confirmed by several pellet diagnostics including a normal-incidence spectrometer for monitoring a tracer impurity behavior.
Structural study, thermal expansion and electrical conductivity of the composition NaSnZr(PO4)3
1993
Abstract The structure of the composition NaSnZr(PO4)3 and its evolution with temperature has been studied. The structure presents the space group R 3 c. The refinement of the structure shows that the Sn and Zr atoms are statistically distributed over the same crystallographic position. The unit cell expands in the c direction and contracts in the a direction, remaining the space group R 3 c at temperatures between 26 and 1000°C. The low value of the electrical conductivity at 400°C, 5.729×10−7S/cm and the low density of the pellets limited the use as electrical conductor.
Shot-by-shot frequency calibration of CARS spectra: Application to the measurement of the collisional line shift in oxygen
1996
A technique using a Fabry-Perot interferometer has been developed to calibrate high-resolution spectra obtained by Coherent Anti-Stokes Raman Spectroscopy (CARS). This technique was used to measure simultaneously the Raman frequency and the Raman signal at each laser shot. We demonstrate the accuracy of the method by measuring theQ(15) line shifts of molecular oxygen due to collisions with oxygen and water vapour.
Formulation, Characterization and Optimization of the Processing Conditions of Blends of Recycled Polyethylene and Ground Tyre Rubbers: Mechanical an…
2005
Abstract Recycling represents a valid alternative to the disposal of post-consumer plastics in common landfills if it is possible to obtain new materials with good final properties compatible with practical application and, above all, by using cheap methods. In this work the possibility to produce secondary materials by blending recycled polyethylene (RPE) coming from greenhouses and post-consumer ground tyre rubber (GTR) has been studied. In particular, the preparation of these blends has been carried out in a common industrial twin screw extruder. RPE pellets and GTR powder were fed to the extruder without any other additive. Temperature, processing speed, mixing procedure and composition…
Effect of Moisture Content on the Processing and Mechanical Properties of a Biodegradable Polyester
2021
This work is focused on the influence of moisture content on the processing and mechanical properties of a biodegradable polyester used for applications in injection molding. The pellets of the biodegradable polyester were exposed under different relative humidity conditions at a constant temperature before being compression molded. The compression-molded specimens were again placed under the above conditions before the mechanical testing. With all these samples, it is possible to determine the effect of moisture content on the processing and mechanical properties separately, as well as the combined effect of moisture content on the mechanical properties. The results obtained showed that th…
Sintering of Fe2NiO4 with an internal binder: a way to obtain a very dense material
2003
Abstract The coupled synthesis and sintering of Fe2NiO4 can be carried out from the calcination under air at high temperatures (>1200 °C) of precompacted (under 12 MPa) pellets of different mixtures: NiO/α-Fe2O3; NiO/α-Fe2O3/Fe; NiO/α-Fe2O3/Ni. The densest material is obtained at 1200 °C only from the following mixture: NiO (40 mol%), α-Fe2O3 (50 mol%) and Ni (10 mol%). Because the metallic nickel is very ductile, it is used as an internal binder in order to enhance the precompacting of the samples. Moreover, the role of nickel is to enhance the sintering reaction. This route leads to a final material of relative density close to 98±2%.