Search results for "Permeability"
showing 10 items of 596 documents
Creep response of a LDPE-based nanocomposite
2016
Polymer nanocomposites and their behavior have been widely investigated by several paths, including mechanical, rheological, and permeability tests, finding that several parameters (such as the polymer matrix, the nanofiller, their amounts, the presence of compatibilizers, processing parameters, etc.) can influence the main properties. However, less information is available regarding the creep response of polymer nanocomposites; in particular, few or no data are reported about the combined effect of different loads and different temperatures. In this article, the creep behavior of a low density polyethylene/organomodified clay nanocomposite has been investigated. The characterization of vis…
Carvacrol affects interfacial, structural and transfer properties of chitosan coatings applied onto polyethylene
2012
Different chitosan coating solutions were tested with the aim of investigating their adhesion and wettability onto polyethylene film to improve packaging performance and provide antimicrobial properties. Surface wetting kinetics was monitored by contact angle measurements. Addition of ethanol and carvacrol improved wettability and adhesion of the thin chitosan layer. Structure, water vapour, O2, CO2 and air permeabilities of self supported chitosan films and coated polyethylene were determined. The formation of a thin chitosan layer on polyethylene improved gas barrier properties decreasing the Permeability Coefficient for oxygen and carbon dioxide ( [Formula: see text] , [Formula: see text…
Structure and thermal properties of a chitosan coated polyethylene bilayer film
2012
The thermal and the structural properties of chitosan coated polyethylene (PE) films were studied. The coating process did not significantly influence the thermal stability and the PE surface structure and/or composition of the polyolefin. Dehydration temperature of chitosan films reflected the strength of water/acetic acid/chitosan chains interactions. Glycerol, used as a plasticizer, formed new hydrophilic centres in the film matrix. Moreover it was better integrated in the CSEGLY than in CSAGLY network. Besides, the addition of a plasticizer in the chitosan films decreased the film degradation temperature. There were two main steps for the PE chitosan coated films degradation. The first …
Simulations of single-fluid flow in porous media
1998
Several results of lattice-gas and lattice-Boltzmann simulations of single-fluid flow in 2D and 3D porous media are discussed. Simulation results for the tortuosity, effective porosity and permeability of a 2D random porous medium are reported. A modified Kozeny–Carman law is suggested, which includes the concept of effective porosity. This law is found to fit well the simulated 2D permeabilities. The results for fluid flow through large 3D random fibre webs are also presented. The simulated permeabilities of these webs are found to be in good agreement with experimental data. The simulations also confirm that, for this kind of materials, permeability depends exponentially on porosity over…
Interaction effect of Nd:YAG laser and universal adhesive system for dentin sealing
2020
Made available in DSpace on 2021-06-25T10:46:55Z (GMT). No. of bitstreams: 0 Previous issue date: 2020-01-01 Background: To evaluate the influence of the association of the universal adhesive system to different energy densities of the Nd:YAG laser on the hydraulic conductance of dentin. Material and Methods: Fifty bovine dentin discs were made. The samples were stratified into four groups (n = 10) according to the treatment performed; SBU- Adper Single Bond Universal (3M ESPE), SBU_60 - SBU associated with the Nd:YAG laser (60mJ, 10Hz, 0.6W - 47.77 J / cm²), SBU_80 - SBU associated with the Nd:YAG laser (80mJ, 10Hz, 0.8 W - 63.69 J / cm2) and C – dentin without treatment (smear layer). Hyd…
Glassy PEEK‐WC vs Rubbery Pebax®1657 Polymers: Effect on the Gas Transport in CuNi‐MOF Based Mixed Matrix Membranes
2020
Mixed matrix membranes (MMMs) are seen as promising candidates to overcome the fundamental limit of polymeric membranes, known as the so-called Robeson upper bound, which defines the best compromise between permeability and selectivity of neat polymeric membranes. To overcome this limit, the permeability of the filler particles in the MMM must be carefully matched with that of the polymer matrix. The present work shows that it is not sufficient to match only the permeability of the polymer and the dispersed phase, but that one should consider also the individual contributions of the diffusivity and the solubility of the gas in both components. Here we compare the gas transport performance o…
Transmission Attenuation Power Ratio Analysis of Flexible Electromagnetic Absorber Sheets Combined with a Metal Layer.
2018
Electromagnetic noise absorber sheets have become a solution for solving complex electromagnetic interference (EMI) problems due to their high magnetic losses. This contribution is focused on characterizing a novel structure that is based on an absorber film with a metal layer attached on its top side. Two different absorber compositions were combined with Al and Cu metal layers in order to study the improvement on the performance of these structures, depending on the complex permeability, absorber film thickness, and type of metal. The transmission attenuation power ratio of the absorber films is analyzed and compared to the performance of absorber and metal structures. The measurement pro…
Novel silver-based nanoclay as an antimicrobial in polylactic acid food packaging coatings.
2010
This paper presents a comprehensive performance study of polylactic acid (PLA) biocomposites, obtained by solvent casting, containing a novel silver-based antimicrobial layered silicate additive for use in active food packaging applications. The silver-based nanoclay showed strong antimicrobial activity against Gram-negative Salmonella spp. Despite the fact that no exfoliation of the silver-based nanoclay in PLA was observed, as suggested by transmission electron microscopy (TEM) and wide angle X-ray scattering (WAXS) experiments, the additive dispersed nicely throughout the PLA matrix to a nanoscale, yielding nanobiocomposites. The films were highly transparent with enhanced water barrier …
Durability of biodegradable polymers for the conservation of cultural heritage
2019
The use of polymers for conservation of cultural heritage is related to the possibility to slow down or stop natural deterioration which, in many cases, corresponds to stopping the entrance of liquid water and to favour spontaneous water vapour removal. Unfortunately, hydrophobicity is generally favoured by surface roughness and thus competitive with transparency. It is therefore important to find an optimal balance hydrophobicity, transparency and durability (especially to photooxidation). However, polymers typically used for applications in this field come from non-renewable resources and are not biodegradable. In this work, the mechanical, structural and optical properties of PLA, PBAT a…
Simulating permeability reduction by clay mineral nanopores in a tight sandstone by combining computer X-ray microtomography and focussed ion beam sc…
2021
Solid earth 12(1), 1 - 14 (2021). doi:10.5194/se-12-1-2021