Search results for "Placement."
showing 10 items of 1123 documents
A multilayer anisotropic plate model with warping functions for the study of vibrations reformulated from Woodcock's work
2013
Abstract In this paper, a suitable model for static and dynamic analysis of inhomogeneous anisotropic multilayered plates is described. This model takes into account the variations of the transverse shear strains through the thickness of the plate by means of warping functions. Warping functions are determined by enforcing kinematic and static assumptions at the interfaces. This model leads to: a 10×10 stiffness matrix coupling to each other the membrane strains, the bending and torsion curvatures, and the x and y-derivatives of the transverse shear strains; and a classical 2×2 transverse shear stiffness matrix. This model has been proven to be very efficient, especially when high ratios be…
Angle Displacement Robust Controller for the Port Plate of the Hydraulic Transformer
2013
The hydraulic transformer is used in the hydraulic system to enhance the efficiency. However, how to control the angle displacement of the port plate is becoming a critical issue because of the new structure of the hydraulic transformer. This paper presents a new method for the angle displacement control system. Firstly, the basic principle of the system is presented. Then, the disturbance which is mainly the friction torque between the port plate and the cylinder block is calculated to estimate the range. Furthermore, the guaranteed cost control (GCC) is analyzed and combined with the disturbance and the characteristics of parameter uncertainties. Finally, the proposed control method is co…
Experimental characterisation of the CIRA plasma wind tunnel SCIROCCO test section
2008
Abstract During the Validation Phase of the CIRA-PWT SCIROCCO Facility located at Capua (Italy), a test campaign has been carried out to verify the performances of the facility with the use of the two conical nozzle configurations “D” and “F” with exit diameters are, respectively of, 1150 and 1950 mm. For the first time the data results of the tests have been used to characterize the plasma flow in the test section of the facility. In particular, analytical relationships between the main thermo-fluid-dynamic parameters in the test section and the reservoir conditions of the facility have been found, and compared to the CFD prediction developed during the Design Phase of the facility. Very i…
Mooring Line Components With Semi-Brittle Behavior: Verification of Fitness for Purpose
2011
Low impact energy for Charpy V Notch (CVN) specimens and associated low Crack Tip Opening Displacement (CTOD) values have occurred on several occasions in high strength steel offshore mooring components. In the present work an Engineering Critical Assessment (ECA) for shackles has been carried out to demonstrate fitness for purpose. Typical values for CVN and CTOD are 17 Joules and 0.01 mm respectively at design temperature. The purpose of the present work is to demonstrate that even in the case where normal quality requirements are not met, the shackles may still have enough structural integrity and fatigue durability to withstand the load spectrum in the field during the planned target se…
Simplified model for compressive response of RC column footing with square cross-section
2017
Abstract In this paper, a simplified calculus model for the prediction of the compressive response of RC column footing with a square cross-section is presented. As it is well-known RC concrete footing are designed adopting uniform contact pressures on the substrate and assuming a strut and tie model in deep members and a cantilever beam or slab model in flexible members. Deep and flexible members are distinguished in literature only based on the tangent of the angle expressed as the ratio between the depth and the shear span of the footing. In this paper, several subgrade contact pressures distribution for column footings (rigid or soft soils) were considered in developing a mechanical mod…
Hardware-in-the-loop implementation for an active heave compensated drawworks
2012
Published version of an article published in the journal: Central European Journal of Engineering. Also available from the publisher at: http://dx.doi.org/10.2478/s13531-011-0062-1 This paper presents the setup and running of a hardware-in-loop (HIL) simulation for an active heave compensated (AHC) draw-works. A simulation model of the draw-works is executed on a PC to simulate the AHC draw-works with a physical PLC. The PLC (ET200S) is configured with a controller architecture that regulates the motor angular displacement and velocity through actuation of the servo valves. Furthermore, a graphical user interface is developed for operation of the AHC system. The HIL test allowed tuning of t…
The Multicriteria Electre III Model Applied to the Evaluation of the Placement of University Graduates
2010
During the last years the Italian university system has been undergoing a reform process regarding issues of governance such as the progressive financial autonomy of the University (art. 5, law 537/24 December 1993) and the reshape of the academic curricula (law 509/99 and 270/04). The most obvious result of this complex process has been the challenging attempt to manage a necessary change in a context of limited financial resources. In order to encompass the composite features of an efficient and effective management of resources, features of high relevance for the full accomplishment of the reform benchmarks, one has to take into account the academic organisation’s objectives, so that to …
Real-time 3D imaging of Haines jumps in porous media flow.
2013
Newly developed high-speed, synchrotron-based X-ray computed microtomography enabled us to directly image pore-scale displacement events in porous rock in real time. Common approaches to modeling macroscopic fluid behavior are phenomenological, have many shortcomings, and lack consistent links to elementary pore-scale displacement processes, such as Haines jumps and snap-off. Unlike the common singular pore jump paradigm based on observations of restricted artificial capillaries, we found that Haines jumps typically cascade through 10–20 geometrically defined pores per event, accounting for 64% of the energy dissipation. Real-time imaging provided a more detailed fundamental understanding o…
Adaptation of two-state (binary) optical fibre loop sensors for industrial use
2005
The paper presents an attempt to unify the construction of two state optical fibre loop sensor and possibility of adapting it to the various traditional constructions and casings of industrial sensors. This enables module structure of sensors based on construction of industrial application (master) and mensurative optical fibre loop (slave). Mensurative properties are determined by traditional (mainly mechanical) measuring system ex. temperature, displacement, and optical properties are determined by characteristics of auxiliary optical system (standardised and unified). Such attitude to a subject is illustrated in this paper by the examples of threshold displacement sensor, temperature, vo…
Thermo-mechanical post-buckling analysis of variable angle tow composite plate assemblies
2017
peer-reviewed The increasing use of composite materials for lightweight structural applications and the extended tailoring capabilities offered by variable stiffness laminates requires rapid and robust analysis tools that adequately describe the mechanical behaviour of such structures. In this work, a Rayleigh–Ritz solution for generally restrained multilayered stiffened variable angle tow plates in the post-buckling regime is presented. The plate model is based on first-order shear deformation theory and accounts for geometrical nonlinearity through von Kármán’s assumptions. General symmetric and unsymmetric stacking sequences are considered and Legendre orthogonal polynomials are employed…