Search results for "Placement"
showing 10 items of 1142 documents
Conservative swept volume boundary approximation
2010
We present a novel technique for approximating the boundary of a swept volume. The generator given by an input triangle mesh is rendered under all rigid transformations of a discrete trajectory. We use a special shader program that creates offset geometry of each triangle on the fly, thus guaranteeing a conservative rasterization and correct depth values. Utilizing rasterization mechanisms and the depth buffer we then get a conservative voxelization of the swept volume (SV) and can extract a triangle mesh from its surface. This mesh is simplified maintaining conservativeness as well as an error bound measured in terms of the one-sided Hausdorff distance. For this we introduce a new techniqu…
VALIDITY, RELIABILITY AND FEASIBILITY OF MEASURING MUSCLE ACTIVITY WITH TEXTILE ELECTRODES EMBEDDED INTO CLOTHING
2007
INTRODUCTION In out-of-laboratory settings the surface EMG measurements are complicated by the requirement of careful electrode placement and skin preparation. The development of washable textile electrodes that can be sowed into sportswear enable muscle activity recordings during normal locomotion without skin preparation and the problem of wires hanging around the body [1]. In this study we performed validity, reliability and feasibility tests of the textile electrodes embedded into shorts against the traditional bipolar surface electrodes.
Hydraulic Models and Finite Elements for Monitoring of an Earth Dam, by Using GNSS Techniques
2016
This work gives a comparison between different mathematicalmodels for the evaluation of the movements of an earthendam situated between Bivona and Alessandria della Rocca, inthe province of Agrigento (AG), Italy. The models selected areof a hydraulic nature, already tested on concrete dams, andfinite elements models which, on the contrary, exploit geotechnicalparameters. The results obtained from the comparisonof the displacement planimetric components and the relativetime series of data over a period of two years appear to befully satisfactory, in fact using both models of a hydraulic andgeotechnical nature, we reach residues of just mm. To supportthis work, a monitoring procedure using GN…
LV Measurement Device Placement for Load Flow Analysis in MV Smart Grids
2016
This paper deals with the issue of measurement device placement for load flow analysis in medium-voltage (MV) distribution networks. The study is carried out using an innovative measurement algorithm for load flow analysis developed by the authors. It is based on low-voltage (LV) load power measurements applied on a backward/forward algorithm for the load flow resolution. The final aim is to identify the most suitable number and placement of the LV measurement points in order to limit the uncertainty on the power flow estimation to a target value. The proposed approach is based on the uncertainty evaluation of the estimated power flows; a sensitivity analysis is performed in order to assess…
A multilayer anisotropic plate model with warping functions for the study of vibrations reformulated from Woodcock's work
2013
Abstract In this paper, a suitable model for static and dynamic analysis of inhomogeneous anisotropic multilayered plates is described. This model takes into account the variations of the transverse shear strains through the thickness of the plate by means of warping functions. Warping functions are determined by enforcing kinematic and static assumptions at the interfaces. This model leads to: a 10×10 stiffness matrix coupling to each other the membrane strains, the bending and torsion curvatures, and the x and y-derivatives of the transverse shear strains; and a classical 2×2 transverse shear stiffness matrix. This model has been proven to be very efficient, especially when high ratios be…
Angle Displacement Robust Controller for the Port Plate of the Hydraulic Transformer
2013
The hydraulic transformer is used in the hydraulic system to enhance the efficiency. However, how to control the angle displacement of the port plate is becoming a critical issue because of the new structure of the hydraulic transformer. This paper presents a new method for the angle displacement control system. Firstly, the basic principle of the system is presented. Then, the disturbance which is mainly the friction torque between the port plate and the cylinder block is calculated to estimate the range. Furthermore, the guaranteed cost control (GCC) is analyzed and combined with the disturbance and the characteristics of parameter uncertainties. Finally, the proposed control method is co…
Experimental characterisation of the CIRA plasma wind tunnel SCIROCCO test section
2008
Abstract During the Validation Phase of the CIRA-PWT SCIROCCO Facility located at Capua (Italy), a test campaign has been carried out to verify the performances of the facility with the use of the two conical nozzle configurations “D” and “F” with exit diameters are, respectively of, 1150 and 1950 mm. For the first time the data results of the tests have been used to characterize the plasma flow in the test section of the facility. In particular, analytical relationships between the main thermo-fluid-dynamic parameters in the test section and the reservoir conditions of the facility have been found, and compared to the CFD prediction developed during the Design Phase of the facility. Very i…
Mooring Line Components With Semi-Brittle Behavior: Verification of Fitness for Purpose
2011
Low impact energy for Charpy V Notch (CVN) specimens and associated low Crack Tip Opening Displacement (CTOD) values have occurred on several occasions in high strength steel offshore mooring components. In the present work an Engineering Critical Assessment (ECA) for shackles has been carried out to demonstrate fitness for purpose. Typical values for CVN and CTOD are 17 Joules and 0.01 mm respectively at design temperature. The purpose of the present work is to demonstrate that even in the case where normal quality requirements are not met, the shackles may still have enough structural integrity and fatigue durability to withstand the load spectrum in the field during the planned target se…
Simplified model for compressive response of RC column footing with square cross-section
2017
Abstract In this paper, a simplified calculus model for the prediction of the compressive response of RC column footing with a square cross-section is presented. As it is well-known RC concrete footing are designed adopting uniform contact pressures on the substrate and assuming a strut and tie model in deep members and a cantilever beam or slab model in flexible members. Deep and flexible members are distinguished in literature only based on the tangent of the angle expressed as the ratio between the depth and the shear span of the footing. In this paper, several subgrade contact pressures distribution for column footings (rigid or soft soils) were considered in developing a mechanical mod…
Hardware-in-the-loop implementation for an active heave compensated drawworks
2012
Published version of an article published in the journal: Central European Journal of Engineering. Also available from the publisher at: http://dx.doi.org/10.2478/s13531-011-0062-1 This paper presents the setup and running of a hardware-in-loop (HIL) simulation for an active heave compensated (AHC) draw-works. A simulation model of the draw-works is executed on a PC to simulate the AHC draw-works with a physical PLC. The PLC (ET200S) is configured with a controller architecture that regulates the motor angular displacement and velocity through actuation of the servo valves. Furthermore, a graphical user interface is developed for operation of the AHC system. The HIL test allowed tuning of t…