Search results for "Plastics"
showing 10 items of 2724 documents
Hygrothermal effect on moisture kinetics and mechanical properties of hemp/polypropylene composite: Experimental and numerical studies
2015
The exposition of thermoplastic composites reinforced with natural fibers to moisture and heat is likely to lower their mechanical properties and restrain their use in the design of parts. The present work is focussed on investigating the effects of hygrothermal aging on the mechanical behaviour of injected polypropylene reinforced with short hemp fibers. Moreover, the kinetic of isothermal moisture absorption has been studied for four immersion temperatures. The experimental results show that the time taken to reach saturation decreases significantly with increase in immersion temperature. These tests also reveal that moisture absorption in this type of materials does not follow Fick's law…
Recycling of compatibilized and uncompatibilized nylon/polypropylene blends
2001
The recycling of compatibilized and uncompatibilized nylon6/polypropylene blends has been carried out by repetitive extrusions. The change of the properties of the blends is a function not only of the number of reprocessing steps but also of the type of compatibilizer. The worsening of the mechanical properties is small and, indeed, some improvement can be observed after one or two extrusion steps for some blends. It is hypothesised that the decrease of the molecular weight, the typical effect occurring during this thermomechanical treatment, is counterbalanced and overcome by the possible formation of new copolymers that act as bridges between the two phases. This behaviour is displayed by…
Synthesis of PP-LCP graft copolymers and their compatibilizing activity for PP/LCP blends
1998
The aim of this work was the synthesis of new graft copolymers consisting of polypropylene (PP) backbones and liquid crystalline polymer (LCP) branches, to be used as compatibilizing agents for PP/LCP blends. The PP-g-LCP copolymers have been prepared by polycondensation of the monomers of a semiflexible liquid crystalline polyester (SBH 1 : 1 : 2), that is, sebacic acid (S), 4,4′-dihydroxybiphenyl (B), and 4-hydroxybenzoic acid (H) in the mole ratio of 1 : 1 : 2, carried out in the presence of appropriate amounts of a commercial acrylic-acid-functionalized polypropylene (PPAA). The polycondensation products, referred to as COPP50 and COPP70, having a calculated PPAA concentration of 50 and…
Structure of isotactic polypropylene/ hydrogenated oligo(cyclopentadiene) blends: 1. Polypropylene-rich blends
1998
Blends of isotactic polypropylene (iPP) and hydrogenated oligo(cyclopentadiene) (HOCP) containing 30% or less HOCP have been studied by small-angle X-ray scattering in the temperature range 25 to 160°C. The structure of blends has been analysed in terms of a pseudo two-phase model consisting of stacks of lamellae whose thickness is a function of temperature and composition. Structural parameters of the model have been derived and their temperature and composition dependences have been interpreted in the light of existing theories.
Necking behavior of low-density polyethylene-isotactic polypropylene blends: A morphological investigation
1984
The tensile behavior of low-density polyethylene-isotactic polypropylene blends was investigated at room temperature. Neck formation and propagation along the whole length of the samples were observed for the whole range of composition. This behavior, which is not indicated by most data available in the literature, was examined in relation to sample morphology by scanning electron microscopy. The results of this investigation indicated some differences between the morphology of these materials and the morphology of blends which do not undergo necking propagation.
Polypropylene-based melt mixed composites with singlewalled carbon nanotubes for thermoelectric applications: Switching from p-type to n-type by the …
2017
Abstract The thermoelectric properties of melt processed conductive nanocomposites consisting of an insulating polypropylene (PP) matrix filled with singlewalled carbon nanotubes (CNTs) and copper oxide (CuO) were evaluated. An easy and cheap route to switch p-type composites into n-type was developed by adding polyethylene glycol (PEG) during melt mixing. At the investigated CNT concentrations of 0.8 wt% and 2 wt% (each above the electrical percolation threshold of ∼0.1 wt%), and a fixed CuO content of 5 wt%, the PEG addition converted p-type composites (positive Seebeck coefficient (S)) into n-type (negative S). PEG was also found to improve the filler dispersion inside the matrix. Two co…
Volatile compounds extracted from polypropylene sheets by hot water :influence of the temperature of sheets injection
1993
A study was made on polypropylene (PP) pellets degraded and not degraded and pointed out the presence and olfactive importance of volatile components extracted from PP pellets by hot water. Plastic packaging materials correspond to a further step of manufacturing: the injection step, and this is often conducted at high temperature. PP (not degraded) and PP-CR (degraded) were transformed into sheets at several temperatures; Lickens-Nickerson extracts were made and allowed the quantification of volatile compounds already identified. A statistical analysis showed that temperature was a very significant parameter. An increasing injection temperature (275 or 300°C° creates increasing quantities …
Functionalized siloxane‐silsesquioxane resins and polypropylene‐based composites: Morphological, structural, thermal, and mechanical properties
2018
Non‐functionalized and n‐alkyl‐functionalized siloxane‐silsesquioxane resins (S4SQ) were synthesized and characterized to confirm their structure and properties. Polypropylene (PP) composites with S4SQ resins as fillers were prepared by the melt blending. The influence of the kinds and amounts of fillers on the structural, morphological and thermal properties as well as mechanical characteristics and processability was determined. High compatibility of composites with functionalized resins resulted in more homogenous dispersion of filler particles in comparison with the composites which contained a non‐functionalized resin. Moreover, the introduction of S4SQ resins into PP strongly affected…
Accelerated weathering of polypropylene/wood flour composites
2008
Abstract Wood–plastic composites (WPCs) have received increasing attention during the last decades, because of many advantages related to their use. Some of their main applications are represented by outdoor furnishing and decking; therefore, it is important to assess their behaviour under UV exposure. In this work, polypropylene/wood flour composites were prepared and their resistance to photooxidation investigated. The composites were prepared by extrusion and compression moulding, and were subjected to mechanical tests, FTIR analysis and molecular weight measurements. The results showed that the composites retained a higher fraction of the original mechanical properties after accelerated…
Improved experimental characterization of crystallization kinetics
2005
Polymer solidification occurring in many processes, like for instance injection molding, compression molding and extrusion, is a complex phenomenon, strongly influenced by the thermo-mechanical history experienced by the material during processing. From this point of view, characterization of polymer crystallization in the range of processing con- ditions, i.e. including high cooling rate, is of great technological and academic interest. Quiescent, non-isothermal crys- tallization kinetics of two polypropylene resins were investigated using a new method, based on fast cooling of thin samples with air/water sprays and optical detection of the crystallization phenomenon. The range of cooling …