Search results for "Plastics"
showing 10 items of 2724 documents
Use of new hydroxytelechelic cis-1,4-polyisoprene (HTPI) in the synthesis of polyurethanes (PUs): Influence of isocyanate and chain extender naturean…
2006
AbstractNew segmented polyurethanes (thermoplastic-elastomers) based on previously described hydroxytelechelic cis-1,4-polyisoprene (HTPI), miscellaneous isocyanates and chain extenders at various equivalent ratios were prepared by the classical one-shot method. The influence of the nature of isocyanate and chain extender, as well as their equivalent ratios, on the mechanical and thermal materials behavior was investigated. Thus, a comparative assessment of material properties was performed. Microphase separation of hard and soft segments was observed by DMTA, DSC and AFM. Moreover, according to Thermogravimetric Analysis (TGA), linear relationships depending on the isocyanate and chain ext…
Sepiolite-reinforced epoxy nanocomposites: Thermal, mechanical, and morphological behavior
2010
A bisphenol A-based epoxy resin was modified with pristine sepiolite and an organically surface-modified sepiolite and thermally cured using two different curing agents: an aliphatic and a cycloaromatic diamine. The nanocomposites were characterized by dynamic mechanical analysis (DMA), rheology, thermogravimetric analysis (TGA), and electron microscopy. The initial sepiolite–epoxy mixtures show a better dispersion for the sepiolite-modified system that forms a percolation network structure. Mechanical properties have also been determined. The flexural modulus of the epoxy matrix slightly increases by the incorporation of the organophilic sepiolite. The flexural strength of the sepiolite-mo…
Modification of polyoxymethylene for increased thermal resistance
2017
Ternary nanocomposites, composed of polyoxymethylene (POM), ethylene octene copolymer and zinc oxide (ZnO), are prepared by melt compounding. The effects of two types of ethylene-octene copolymers, differing with α-octene content (38% for EOC38 and 17% for EOC17), as well as nanostructured ZnO on thermal behavior of POM are investigated. The content of EOC in the POM based composites is varied between 10 and 50 wt%, while the content of ZnO is 2 wt%. Thermal behavior of POM based systems are studied by using differential scanning calorimetry and thermogravimetric analysis coupled with Fourier transform infrared spectroscopy. Results of thermogravimetric analysis show that, by rising either …
Comparative study of historical woods from XIX century by thermogravimetry coupled with FTIR spectroscopy
2019
Thermal and structural properties of historical woods from apparatuses of the Historical Collection of the Physics Instruments of the University of Palermo have been investigated by FTIR spectroscopy coupled with thermogravimetric analysis. Specifically, the wooden portions of apparatuses from XIX century have been studied. The investigated woods belong to different taxa (Swietenia mahagoni, Picea abies and Juglans regia). The thermal behavior of the wooden materials has been successfully interpreted on the basis of specific indexes determined by the quantitative analysis of the FTIR spectra. The kinetics of the wood pyrolysis have been investigated by using a non-isothermal approach based …
Structural, mechanical and thermal behavior assessments of PCL/PHB blends reactively compatibilized with organic peroxides
2018
Abstract The efficiency of two commercially available organic peroxides, dicumyl peroxide (DCP) and di-(2-tert-butyl-peroxyisopropyl)-benzene (BIB), during reactive processing of poly(e-caprolactone)/poly(3-hydroxybutyrate) (PCL/PHB) blends was investigated. The changes in chemical structure of PCL/PHB blends, as a function of organic peroxide type (DCP/BIB) and content (in range: 0–1.0 parts by weight - pbw), were characterized by Fourier transform infrared spectroscopy, thermogravimetric analysis combined with infrared spectroscopy, and headspace analysis combined with gas chromatography with flame ionization detector. Performance properties of PCL/PHB blends were evaluated based on diffe…
Synthesis, Characterization and Sorption Capacity Examination for a Novel Hydrogel Composite Based on Gellan Gum and Graphene Oxide (GG/GO)
2020
A novel hydrogel composite based on gellan gum and graphene oxide (GG/GO) was synthesized, characterized and tested for sorption capacity in this work. The microstructural, thermogravimetric and spectroscopic analysis confirmed the formation of the GG/GO composite. Comparative batch sorption experiments revealed a sorption capacity of the GG/GO composite for Zn (II) ions of approximately 2.3 higher than that of pure GG. The GG/GO composite exhibits a maximum sorption capacity of 272.57 mg/g at a pH of Zn (II) initial solution of 6. Generally, the sorption capacity of the sorbents is approximately 1.5 higher in slightly acidic conditions (pH 6) comparative with that for strong acidic conditi…
Solid state 13C-NMR methodology for the cellulose composition studies of the shells of Prunus dulcis and their derived cellulosic materials.
2020
Lignocellulosic fibers and microcellulose have been obtained by simple alkaline treatment from softwood al- mond shells. In particular, the Prunus dulcis Miller (D.A.) Webb. was considered as a agro industrial waste largely available in southern Italy. The materials before and after purification have been characterized by 13C CPMAS NMR spectroscopy methodology. A proper data analysis provided the relative composition of lignin and holo- cellulose at each purification step and the results were compared with thermogravimetric analysis and FT-IR. To value the possibility of using this material in a circular economy framework, the fibrous cellulosic material was used to manufacture a handmade c…
Tunable Structure and Properties of Segmented Thermoplastic Polyurethanes as a Function of Flexible Segment
2019
Segmented thermoplastic polyurethanes (PUs) were synthetized using macrodiols with different functional groups (carbonate, ester, and /or ether) as a segment with a molar mass of 1000 and 2000 g/mol, and 4,4&rsquo
RHEOLOGICAL BEHAVIOUR OF MICROCRYSTALLINE CELLULOSE HYDROGELS
1992
ABSTRACT An extensive study was made of the rheological behaviour of microcrystal1ine cellulose-sodium carboxymethyl cellulose (MCC-NaCMC) gels at six different concentrations. The effect of agitation time, storage time, shear rate and temperature on the viscosity of these thixotropic gels was analysed, over 7200 resulting values of being available to this effect The pseudoplastic and thixotropic characteristics of the gels was established and a progressive decrease in gel viscosity with increasing storage time was observed, although retaining stability. On the other hand, constant agitation for five minutes was found to reduce gel viscosity by 40 to 50%, regardless of concentration.
Thixotropic Behavior of Salad Dressings Stabilized with Modified Starch, Pectin, and Gellan Gum. Influence of Temperature
2008
The thixotropy of low‐oil salad dressing has been analyzed at different temperatures (8–26°C). The usual formulation containing modified starch (4%) was compared with others in which part of the starch had been substituted by pectin (0.5%) or different concentrations of gellan (0.1 and 0.5%). Up and down flow curves were measured, showing in all cases shear thinning behavior and fitting the Herschel‐Bulkley model. Thixotropic areas enclosed by the up curve and the corresponding different down curves, STh, were obtained. With the aim of establishing comparative results, and since the viscosities were quite different, the parameter considered was relative thixotropic area, SR (%)=100 (STh/Sup…