Search results for "Polymers and Plastics"

Interface evolution during magnetic pulse welding under extremely high strain rate collision: mechanisms, thermomechanical kinetics and consequences

2020

Abstract Magnetic pulse welding enables to produce perplexing interfacial morphologies due to the complex material response during the high strain rate collision. Thus, a thermomechanical model is used in this study to investigate the formation mechanism of the wake, vortex, swirling and mesoscale cavities with the increase of the impact intensity at the interface. The formation of these interfacial features are difficult to characterize by insitu methods, thus the origin of phenomena still remain a subject of open discussion. Our studies identify the governing mechanisms and the associated thermomechanical kinetics, which are responsible for the formation mechanism of interfacial features.…

Synergistic effect of fiber content and length on mechanical and water absorption behaviors of Phoenix sp. fiber-reinforced epoxy composites

2016

Phoenix sp. fiber-reinforced epoxy composites have been manufactured using compression molding technique. The effect of reinforcement volume content (0%, 10%, 20%, 30%, 40%, and 50%) and size (300 µm particles, 10 mm, 20 mm, and 30 mm fibers) on quasi-static and dynamic mechanical properties was investigated. Moreover, the water absorption properties of composites were analyzed at different environmental conditions (10℃, 30℃, and 60℃). For each reinforcement size, composites loaded with 40% in volume show highest tensile and flexural properties. Furthermore, composites with 300 µm particles present the best impact properties and the lowest water absorption, regardless of the environmental …

Effect of AlR3 (R = Me, Et, iBu) addition on the composition and microstructure of ethylene/1-olefin copolymers made with post-metallocene complexes …

2018

The effect of trialkylaluminum compound (AlR3, where R = Me, Et, iBu) addition on the performance of the [LigZrCl]2(μ-O)/AliBu3/Ph3CB(C6F5)4 and LigTiCl2/AliBu3/Ph3CB(C6F5)4 (Lig = Me2N(CH2)2N(CH2-2-O-3,5-tBu2-C6H2)2) catalysts in ethylene/1-olefin copolymerization was investigated. The presence of AlMe3 in the feed during the copolymerization process catalyzed by the diamine-bis(phenolate) zirconium catalyst greatly increases the amount of incorporated comonomer and leads to microstructural changes, e.g., the formation of blocky and alternating sequences of 1-olefin units. Moreover, the use of AlMe3 limits the reaction yield and decreases the molecular weight of the produced copolymers. Th…

The complementary structural studies of the double metal cyanide type catalysts for the ring opening polymerization of the oxiranes

2016

Lignin Inter-Diffusion Underlying Improved Mechanical Performance of Hot-Pressed Paper Webs

2021

Broader use of bio-based fibres in packaging becomes possible when the mechanical properties of fibre materials exceed those of conventional paperboard. Hot-pressing provides an efficient method to improve both the wet and dry strength of lignin-containing paper webs. Here we study varied pressing conditions for webs formed with thermomechanical pulp (TMP). The results are compared against similar data for a wide range of other fibre types. In addition to standard strength and structural measurements, we characterise the induced structural changes with X-ray microtomography and scanning electron microscopy. The wet strength generally increases monotonously up to a very high pressing tempera…

Carvacrol activated biopolymeric foam: An effective packaging system to control the development of spoilage and pathogenic bacteria on sliced pumpkin…

2021

Abstract A commercial biodegradable starch-based polymer (Mater-Bi) was activated with carvacrol to develop a biodegradable and compostable polymer to be used in food packaging. Based on previous tests, carvacrol was added at 20 % weight of foam. MB foams, with and without carvacrol, were tested for their morphological characteristics, mechanical tests and kinetics of carvacrol release under refrigerated storage conditions. Carvacrol slightly increased the porosity of the foams, induced a reduction of the compressive elastic modulus (Ecom) of foamed MB from 6 to ∼ 3.4 MPa and a decrease of the tensile elastic modulus from ∼70 MPa to ∼16.5 MPa. Carvacrol release from the foam at 4 °C was alm…

Fresh-cut storage of fruit and fresh-cuts affects the behaviour of minimally processed Big Bang nectarines ( Prunus persica L. Batsch) during shelf l…

2018

Abstract Nectarine can be minimally processed to successfully produce ready-to-eat fresh-cuts fruit. The aim of this work was to study the combined effect of the ripening stage of cold stored fruit before processing and the length of the storage period of fresh-cut slices after minimal processing, on the behaviour of minimally processed “Big Bang” nectarines during shelf life. ‘Big Bang’nectarine slices obtained from fruit stored at 1 ± 0.5 °C (RH = 90%) for 1 d, 10 d and 15 d were stored for 0, 3, 5, 7, 12 d. at 5 °C. At the end of each storage period, visual quality, color (L*, a* and b*), phenols and carothenoids content, TSS, TA were measured together with in-package CO2 and O2. Despite…

Thermoplastic starch and green tea blends with LLDPE films for active packaging of meat and oil-based products

2019

International audience; Thermoplastic starch (TPS) is an alternative biomaterial that can be used to produce bioplastics to replace petroleum-based food packaging. Active films were developed from acetylated cassava TPS and green tea using the blown extrusion process. Green tea (GT) and TPS from native starch (NS) and acetylated starch (AS) with different degrees of substitution (DS) were extruded with linear low-density polyethylene (LLDPE) at LLDPE/TPS-GT ratios of 70/30 and 60/40 prior to blown-film extrusion. Results indicated that a higher DS of AS enhanced melt flow index which altered processability and subsequently impacted film microstructures and physical and barrier properties. N…

On the use of Persian gum for the development of antiviral edible coatings against murine norovirus of interest in blueberries.

2021

In the last decades, berries have been identified as important vehicles for the transmission of foodborne viruses and different strategies are being explored to eliminate or reduce viral contamination in these fruits. The aim of this work was to develop novel edible coatings with antiviral properties for inactivating and reducing murine norovirus (MNV). Firstly, the effect of gelatin (G) addition on Persian gum (PG) films was studied in terms of microstructural, mechanical, optical, and water barrier properties. The following PG:G ratios were considered: 100:0, 75:25, 50:50, 25:75, and 0:100. Microstructure analysis revealed the compatibility of both hydrocolloids since no phase separation …

Failure maps to assess bearing performances of glass composite laminates

2018

Aim of this article is the assessment of the bearing mechanical performances of pin-loaded glass laminates as function of their geometrical configuration. To this concern, 32 specimens having different hole diameter (D), laminate width (W), and hole center to laminate free edge distance (E) have been tested under bearing conditions. The maximum bearing stress and the stress-displacement curves were analyzed as function both of hole to laminate free edge distance E and hole diameter D. Moreover, an experimental 2D failure map was created by placing the experimental results (i.e., the kind of failure mechanism occurred for each geometrical configuration) in the plane E/D versus W/D ratios. In…