Search results for "Polyp"
showing 10 items of 1415 documents
Effect of a Compatibilizer on the Morphology and Properties of Polypropylene/Polyethylentherephthalate Spun Fibers
2017
Fibers spun by melt spinning of binary and ternary polypropylene/ polyethylenetherephthalate blends have been produced and characterized in order to investigate the effect of a compatibilizer on their morphology and mechanical properties. The compatibilizer was a maleic anhydride-functionalized rubber copolymer. The effect of the compatibilizer was well evident in the isotropic state, as the morphology became very fine, the size of the dispersed particles was very small, and the adhesion was better. The effect of the compatibilizer on the mechanical properties is very relevant, especially in the elongation at break. On the contrary, no relevant effect was observed in the anisotropic oriente…
Palladium nanoparticles–polypyrrole composite as an efficient catalyst for cyanation of aryl halides
2014
Abstract New palladium-polypyrrole (Pd/PPy) nanocomposites have been studied in cyanation of aryl halides with K 4 Fe(CN) 6 and showed high catalytic efficiency. Aryl iodides, bromides, and chlorides are active. The reaction can be performed both in organic solvents and in water; in the latter case, the catalyst was immobilized on graphite support. The cyanation of inactivated aryl chlorides is of special importance as only a few publications dealing with efficient cyanation of aryl chlorides are available, in which expensive and poisonous phosphine ligands and non-aqueous solvents are used. The influence of the morphology of the catalyst on its efficiency in cyanation was investigated, and…
Electrochemical deposition of polypyrrole nanolayers on discontinuous ultrathin gold films.
2008
Ultrathin layers of polypyrrole (PPy) were electrochemically grown between microelectrodes on a $Si/SiO_2$ substrate. Conducting nanolayers of PPy are directly grown onto ultrathin discontinuous gold (Au) film between the microelectrodes, with thicknesses in the range 10–100 nm. The system therefore forms a novel (PPy/Au) nanocomposite conductor. Atomic force microscopy (AFM) imaging and conductivity measurements indicate that at all thicknesses a relatively uniform film is formed but with significant roughness that reflects the roughness of the metallic island layer. In PPy/Au films with thickness $\sim 10 nm$, the small barriers around the gold islands dominate the conduction, and as the …
Nonlinear Transport in Hybrid Polypyrrole–Gold Nanostructures
2010
We have studied charge transport in nanometer scale films of polypyrrole (PPy) that were grown electrochemically onto discontinuous ultrathin films of gold. The gold films consisted of 100 nm size islands, separated from each other by nanometer-size gaps. The thickness of PPy can be varied from 30 to 200 nm. The I-V characteristics of these hybrid PPy-Au nanostructures show strong non-linearity at low temperatures, and in particular for the more insulating samples. The hopping transport is further verified from the log / versus V-1/4 plots. Furthermore, the I-V data follow an empirical relation dlog//dV(1/4) similar to T-1/2.
Effect of processing temperature and mixing time on the properties of PP/GnP nanocomposites
2020
Abstract During processing of molten polymers the thermal and mechanical stress acting on the melt in presence of oxygen can induce degradation with a modification of the chemical structure of the polymers. This picture can become even more relevant if the melt is a multiphasic polymer system. In this last case, the effects of the degradation depend also on the presence of a second phase and on the interactions between the two phases. In this work, the effect of the processing conditions, temperature and time, have been considered in order to investigate the thermo-mechanical and thermo-oxidative degradation of nanocomposites made by polypropylene and different contents of graphene nanoplat…
Effect of the additive level and of the processing temperature on the re-building of post consumer pipes from polyethylene blends
2007
Abstract One of the main shortcomings of the mechanical recycling is that the properties of the secondary materials are generally sensibly inferior with respect to the virgin ones. This feature implies, for sure, that they cannot be used for the same technological application but also other uses of the secondary material are impossible. The aim of this work is to study the re-building of recycled post-consumer pipes, made of a blend of different polyethylenes, by re-processing in the presence of a nitroxyl compound as radical generator. The processing temperature and the additive concentration have been varied in order to study the effect of these parameters on the final properties. The mec…
Investigation on the Properties and on the Photo-Oxidation Behaviour of Polypropylene/Fumed Silica Nanocomposites
2021
This work investigates the effects of very small amounts of fumed silica on the morphology and on the rheological and mechanical behaviour of polypropylene nanocomposites and on their photo-oxidation behaviour. Polypropylene nanocomposites were prepared using a twin-screw corotating extruder with 0, 1 and 2 wt/wt% of SiO2. Morphological, mechanical, thermomechanical and rheological properties were examined. It was found that the viscosity of the matrix is reduced by the presence of the silica nanoparticles, suggesting a poor adhesion between the two phases and probably some lubricating effect. On the contrary, the mechanical and, in particular, the thermomechanical properties of the matrix …
Accelerated weathering of PP based nanocomposites: Effect of the presence of maleic anhydryde grafted polypropylene
2013
Polymer nanocomposites are currently a topic of great interest. The increasing importance they are gaining also in the standpoint of industrial applications, is giving concerns regarding their environmental stability and, in general, their behaviour in outdoor applications, under direct solar irradiation. Papers available in the literature have highlighted the different influences of different nanosized fillers, in particular clay-based nanofillers; however, few data are available regarding other nanosized fillers. Furthermore, the research on polymer nanocomposites has clearly pointed out that the use of compatibilizers is required to improve the mechanical performance and the dispersion o…
Photo-oxidation of polypropylene/graphene nanoplatelets composites
2019
Abstract The photo-oxidation behaviour of polymer nanocomposites depends not only on the photo-oxidation behaviour of the matrix, but also on the chemical composition, on the physical properties of the nanoparticles and on the possible interactions between the two phases. In the case of nanocomposites with carbonaceous particles, the main effect is a photo-stabilization due to the absorption of the UV energy and the radical scavenging action. In this work we investigated the effect of the presence of graphene nanoplatelets on the photo-oxidation behaviour of the polypropylene. The presence of the graphene nanoplatelets improves the photo-resistance of the polypropylene and this effect incre…
Accelerated laboratory weathering of polypropylene composites filled with synthetic silicon-based compounds
2019
Abstract Non-functionalized and n-alkyl functionalized polyhedral oligomeric silsesquioxanes (POSS), siloxane-silsesquioxane resins and the sol-gel silicas were for the first time examined as possible UV-stabilizers and/or antioxidants in polypropylene (PP). The obtained composites were subjected to the accelerated laboratory weathering tests. The influence of the weathering conditions on the structure and properties of the PP materials was evaluated on the basis of the results from Fourier transform infrared spectroscopy (FTIR), scanning electron microscopy (SEM) and differential scanning calorimetry (DSC) studies. It was found that weathering resistance of the PP materials was strongly de…