Search results for "Pressure"

A New Simple Friction Model for S. I. Engine

2009

Internal combustion engine modeling is nowadays a widely employed tool for modern engine development. Zero and mono dimensional models of the intake and exhaust systems, combined with multi-zone combustion models, proved to be reliable enough for the accurate evaluation of in-cylinder pressure, which in turn allow the estimation of the engine performance in terms of indicated mean effective pressure (IMEP). In order to evaluate the net engine output, both the torque dissipation due to friction and the energy drawn by accessories must be taken into consideration, hence a model for the friction mean effective pressure (FMEP) evaluation is needed. One of the most used models accounts for engin…

Effect of pressure on the PVT behaviour of iPP as revealed by dilatometric measurements

2002

Isotactic Poly-propylene samples, previously prepared under known conditions of pressure and cooling rate by means of a special apparatus designed and set-up by the authors, were subjected to several isobaric runs at low cooling and heating rate in a confining fluid dilatometer (by GNOMIX). The effect of the previous thermo-mechanical histories and the effect of pressure in the dilatometry on specific volume of the samples was studied. Results show that the initial specific volume depends upon the previous thermo-mechanical histories, which however cancels out after the first heating run. Moreover the reported dilatometric experimental data support the evidence that an increase of pressure …

CFD parametrical study of the spacer geometry for Membrane Distillation

Membrane Distillation (MD) is a thermal process that separates water from aqueous solutions containing non-volatile components such as salt. Water vapor from the hot feed channel permeates through a hydrophobic membrane thanks to a partial pressure gradient, and condenses in the cool channel. One of the main advantages of MD is the easy coupling with renewable resources, as the solar thermal energy. In the various MD configurations developed, net spacers are used in order to support the membrane, thus creating the channels; moreover, they can counteract the side effects of temperature polarization by promoting mixing. However, the presence of the spacer involves an increase of pressure drop…

CFD prediction of flow, heat and mass transfer in woven spacer-filled channels for membrane processes

2021

Abstract Flow and heat or mass transfer in channels provided with woven spacers made up of mutually orthogonal filaments were studied by Computational Fluid Dynamics. The problem addressed was the combined effect of the parameters that characterize the process: pitch to height ratio P/H (2, 3 and 4), flow attack angle θ (0, 7, 15, 20, 30, 40 and 45°) and Reynolds number Re (from ~1 to ~4000). The Prandtl number was 4.33, representative of water at ~40°C, while the Schmidt number was 600, representative of NaCl solutions. Simulations were performed by the finite volume code Ansys CFX™ 18.1 using very fine grids of ~6 to ~14 million volumes. For Re > ~400, the SST turbulence model was used to…

A 2-D model of electrodialysis stacks including the effects of membrane deformation

2021

Abstract Membrane-based processes have gained a relevant role in many engineering applications. Much effort has been devoted to thoroughly understand the fundamental phenomena behind them. However, membrane deformation has been taken into consideration only recently, although much evidence has shown its impacts in many applications. This work presents a novel 2-D, multi-scale, semi-empirical process model able to predict the behavior and the performance of Electrodialysis (ED) systems in cross-flow configurations in the presence and absence of local membrane deformations. The model exploits the results and the simulation approaches of previous fluid-structure investigations performed by the…

Pressure drop at low reynolds numbers in woven-spacer-filled channels for membrane processes: CFD prediction and experimental validation

2017

The energy consumption due to pumping power is a crucial issue in membrane processes. Spacers provide mechanical stability and promote mixing, yet increasing pressure drop. Woven spacers and their behaviour at low Reynolds numbers are less studied in the literature. Nevertheless, they are typical of some membrane technologies, as reverse electrodialysis (RED). RED is a promising technology for electric power generation by the chemical potential difference of two salt solutions within a stack equipped by selective ion-exchange membranes. The mechanical energy required for pumping the feed solutions, can dramatically reduce the net power output. In this work computational fluid dynamics (CFD)…

CFD modelling of profiled-membrane channels for reverse electrodialysis

2014

Abstract: Reverse electrodialysis (RE) is a promising technology for electric power generation from controlled mixing of two differently concentrated salt solutions, where ion-exchange membranes are adopted for the generation of ionic currents within the system. Channel geometry strongly influences fluid flow and thus crucial phenomena such as pressure drop and concentration polarization. Profiled membranes are an alternative to the more commonly adopted net spacers and offer a number of advantages: avoiding the use of non-conductive and relatively expensive materials, reducing hydraulic losses and increasing the active membrane area. In this work, Computational Fluid Dynamic simulations we…

CFD simulation of Electrodialysis channels equipped with profiled membranes

Electrodialysis (ED) is a membrane-based electrochemical process that remove ions from a solution. The main use of ED is for the production of drinking water by brackish water desalination, but there are several other applications. ED is characterized by the coexistence and the interaction of different physical phenomena that affect the stack performance. Among them, fluid dynamics and mass transport are crucial: concentration polarization affects the limiting current density and the non-Ohmic voltage drop due to the chemical potential difference between the two solutions; pressure drop affects the pumping power consumption. Moreover, the total energy consumption depends also on the Ohmic v…

Flow and mass transfer in spacer-filled channels for reverse electrodialysis: a CFD parametrical study

2016

Abstract In reverse electrodialysis (RED) concentration polarization phenomena and pressure drop affect strongly the power output obtainable; therefore the channel geometry has a crucial impact on the system optimization. Both overlapped and woven spacers are commonly commercialised and adopted for RED experiments; the latter exhibit some potential advantages, such as better mixing and lower shadow effect, but they have been poorly investigated in the literature so far. In this work, computational fluid dynamics was used to predict fluid flow and mass transfer in spacer-filled channels for RED applications. A parametric analysis for different spacer geometries was carried out: woven (w) and…

CFD analysis of the fluid flow behavior in a reverse electrodialysis stack

2012

Salinity Gradient Power by Reverse Electrodialysis (SGP-RE) technology allows the production of electricity from the different chemical potentials of two differently concentrated salty solutions flowing in alternate channels suitably separated by selective ion exchange membranes. In SGP-RE, as well as in conventional ElectroDialysis (ED) technology, the process performance dramatically depends on the stack geometry and the internal fluid dynamics conditions: optimizing the system geometry in order to guarantee lower pressure drops (DP) and uniform flow rates distribution within the channels is a topic of primary importance. Although literature studies on Computational Fluid Dynamics (CFD) a…