Search results for "Principi"

Photocatalytic membrane reactors: fundamentals, membrane materials and operational issues

2013

Abstract: This chapter reports the properties of semiconductor materials used in heterogeneous photocatalysis together with a comparison of heterogeneous photocatalytic systems and a brief description of the types of membranes that can be used. Some aspects of membrane operations, such as fouling, separation of a photocatalyst and effectiveness of photodegradation on permeate quality are discussed.

Poly lactic acid based foams prepared via thermally induced phase separation (TIPS): A method to tune the crystallinity

2012

Blends of Poly-L-Lactic Acid (PLLA) with two Poly-Lactic Acid (PLA) in different proportions (90/10 and 70/30) were utilized in order to produce biodegradable and biocompatible scaffolds for soft tissue engineering applications. The scaffolds were produced via thermally induced phase separation (TIPS) starting from ternary systems where dioxane was the solvent and water the non-solvent. Morphology was evaluated by Scanning Electron Microscopy (average pore size and interconnection). Moreover a DSC analysis was carried out on the as-obtained scaffold in order to obtain information about theirs thermal properties (enthalpy of melt and crystallization). The results showed that is possible to p…

A study via simulation of solidification during injection molding

2011

The final properties of an injection-molded part are strictly dependent on the solidification dynamics occurring during the processing. The experimental derivation of information about polymer solidification throughout the injection molding cycle is still an open challenge. To overcome the practical issues, the process simulation is proposed as a mean to derive useful data, and especially for identifying the most influencing parameters. The no-flow temperature (NFT) is a parameter used in most of injection molding simulation packages as a mean to determine whether the polymer flows or it is solid. With this simple parameter it is possible to take into account the rheological solidification …

Process Intensification by Using Ozonation Coupled with TiO2 Photocatalysis for Treating Bromide and/or Bromate Ions Containing Water: The Role of Co…

2014

The solidification behavior of a PBT/PET blend over a wide range of cooling rate

2009

In recent years, much attention has been paid to the development of high-performance polyester blends, among which blends of polybutylene terephtha- late/polyethylene terephthalate (PBT/PET) are expected to exhibit remarkable prop- erties as far as their crystallization behavior is concerned. Through trial and error, appropriate commercial compositions have been chosen which could not be otherwise explained by a suitable interpretation of the mechanisms determining their solidifica- tion behavior. The solidification behavior of a 60/40 w/w PBT/PET blend was studied in a wide range of cooling conditions, according to a continuous cooling transforma- tion (CCT) procedure developed previously,…

Visible Light Induced Oxidation of Ferulic Acid by TiO2 Photocatalysis

2012

Oxidation of ferulic acid (C10H10O4) in aqueous medium occurs by using both commercial and home prepared TiO2 samples under visible light irradiation. Among the oxidation products vanillin was found with a selectivity ranging from 1 to 2% with respect to the converted substrate. By considering that TiO2 is unable to absorb visible light and ferulic acid does not react in the absence of TiO2, the observed photoactivity may be explained by the formation of a charge-transfer complex between ferulic acid and TiO2, being the complex able to absorb visible light. Among all the tested semiconductor oxides, only Merck anatase TiO2 does not perform the oxidation of ferulic acid under visible light i…

Guidelines for the Assessment and the Validation of the Rate Law of Slurry Photocatalytic Reactions

2017

The assessment of the rate law of slurry photocatalytic reactions appears to be a hard task, mainly because in this type of reactions the average rate of reaction, which is experimentally observed in a real reactor, could be very different from the “true” (intrinsic) rate of reaction, which cannot be measured directly. In the present work, it is shown how a proper mathematical model allows the utilization of the differential and/or the integral methods of kinetic analysis. The mathematical model must take into account not only the momentum and the mass balances, but also the radiative transfer equation. However, the discrimination among different proposed kinetic laws remains difficult sinc…

Photocatalytic Ozonation of Bromide Containing Waste Water: Related Problems and Kinetics Based Strategy Evaluation

2015

In the so-called photocatalytic ozonation (PO) synergistic effects between photocatalysis and ozonation enhance the rate of oxidation of organic compounds, therefore this integrated process is very promising for use in water treatment. In the present work, it is demonstrated that the improvement that can be obtained by the integrated process in comparison with the uncoupled processes depends on the relative weight between photocatalysis and ozonation. In this respect, it has been found that a relatively low rate of photocatalysis (0.3 times the rate of ozonation) is sufficient to get the highest synergy and to maximize the performances in the oxidation of formate, the adopted model organic …

Synthetic Green Chemistry through Heterogeneous Photocatalysis

2015

This contribution deals with a short review of some application of TiO2 to green organic synthesis. In particular to selective oxidation of aromatic alcohols under mild conditions.

Green Organic Reactions by TiO2 Photocatalysis

2015

This contribution gives an account of TiO2-based selective photocatalysis as a green synthetic tool for the production of organics. Some case studies of the most common transformations carried out by means of photocatalytic reactions are illustrated.