Search results for "REINFORCED"
showing 10 items of 236 documents
Simplified flexural response of steel-fiber reinforced concrete beams
2008
In the present paper, an analytical model is proposed that is able to determine the flexural response of supported beams under four-point bending tests. Cases of normal strength reinforced concrete beams with longitudinal bars in the presence of reinforcing hooked steel fibers and transverse stirrups are considered. A simplified analytical model is presented that is able to calculate the load-deflection curves and the maximum and ultimate deflections occurring in the case of shear or flexure failures. In the case of shear failure, the maximum shear strength of the beams is evaluated by using a recent analytical expression proposed by the author able to account for the shear-to-moment intera…
Generalization of Shear Truss Model to the Case of SFRC Beams with Stirrups
2012
A theoretical model for shear strength evaluation of fibrous concrete beams reinforced with stirrups is proposed. The formulation is founded on the theory of plasticity and the stress field concepts, generalizing a known plastic model for calculating the bearing capacity of reinforced concrete beams, to the case of fibrous concrete. The beneficial effect of steel fibres is estimated taking into account the residual tensile strength of fibrous concrete, by modifying an analytical constitutive law which presents a plastic plateau as a post-peak branch. Around fifty results of experimental tests carried out on steel fibrous concrete beams available in the literature were collected, and a compa…
Finite element modelling of slipage between FRP rebar and concrete in pull-out test
2014
The paper presents numerical results of direct pull-out test of glass fiber-reinforced polymer (GFRP) rebars embedded in concrete. Rebars of three different cross-sections are considered: circular without longitudinal ribs and with two and four ribs. The design analyses of the rebar configurations embedded in concrete are investigated by the 3D finite element method (FEM), which takes into account the non-linearity using ANSYS software. The results of the numerical model with two ribs were compared with the experimental results. Then, the effect of different rebar geometries to the load-slip pull-out curves was studied. It is concluded that the influence of rib height and width on the pull-…
Masonry infills and RC frames interaction: Literature overview and state of the art of macromodeling approach
2015
The issue of the influence of masonry infills within RC frames structures has been widely investigated in the last decades by several researchers. The large interest addressed to this topic depends on the actual observation that when in presence of seismic events, the response of framed structures is strongly conditioned by the interaction with the infill walls, which however are considered as non-structural elements and not included in the models. The influence of masonry infills role in structural response is so much relevant to affect not only the overall strength and the stiffness but it may also radically change the possible collapse mechanisms of the overall structural complex under t…
Flexural behaviour of external R/C steel fibre reinforced beam-column joints
2011
ABSTRACT A softened strut-and-tie macro model able to reproduce the flexural behaviour of external beam-column joint is presented. The model is specific for concrete with hooked steel fibres (FRC) and it is designed to calculate the flexural response, as load-deflection curve, of a beam-column sub-assemblages. The model considers the presence of a constant vertical load acting on the column and of a monotonically increasing lateral force applied at the tip of the beam.
Concrete columns confined with fibre reinforced cementitious mortars: Experimentation and modelling
2014
Abstract The structural behaviour of concrete columns strengthened with a system made up of fibre nets embedded in an inorganic stabilized cementitious matrix under an uniaxial load was investigated. Medium size specimens with circular and square cross-section were cast and subjected to monotonic uniaxial compression, to investigate the efficiency of a p-Phenylene BenzobisOxazole (PBO) Fibre Reinforced Cementitious Mortar (FRCM) system in increasing both strength and ductility. The experimental results show that the confinement system adopted produced a noticeable increment in strength and ductility, though the low mechanical ratios of fibre considered were not always able to ensure hardeni…
Effect of FRP strengthening on the flexural behaviour of calcarenite masonry walls
2017
The use of fiber-reinforced polymers (FRP) for structural strengthening has become increasingly popular in recent years. Several applications of FRP have been proposed and applied, depending on the target of the technique, kind and/or material of the structural member. In particular, because of their great tensile strength, FRP materials are commonly used to enhance the out-of-plane behaviour of masonry walls, allowing to increase their strength, ductility and improving safety against overturning. For these reasons, FRP laminates are often applied in vulnerable ancient buildings in seismic areas to reinforce façades and walls with poor structural features. However, some issues arise when a…
R.C. columns strengthened by PBO-FRCM under axial force and bending moment
2017
Fabric-Reinforced Cementitious Matrix (FRCM) systems, also known as Textile Reinforced Concrete (TRC) are nowadays widely used as confining material to enhance both strength and deformation capacity of columns of seismic resistant r.c. frames. In the past, when carbon fiber was used in the textile, experimental results showed that the efficiency of the wrapping is limited by the connection between substrate and fiber, which is not as effective as when epoxy resins are used. To improve the strength of the connection between fibres and mortar binder in FRCM system, the use of p-Phenylene BenzobisOxazole (PBO), having a molecular structure capable of establishing chemical bonds with hydrated c…
Evaluation of interlaminar delaminations in titanium-graphite fibre metal laminates by infrared NDT techniques
2018
Abstract Fibre Metal Laminates (FMLs) describe a number of aerospace-grade layered structural materials where thin metal alloy foils are interleaved with Fibre Reinforced Polymer (FRP) plies. Such material hybridisation at the layer meso-scale poses a challenge for non-destructive testing (NDT). On the other hand, the need for NDT inspection of FMLs arises due to the potential development of interlayers disbonds, both during fabrication or in-service. This work describes the successful implementation of two Infrared-NDT approaches to evaluate a defected FML panel made of Titanium/Graphite (Ti-Gr). One technique is based on the modulation of the deployed heat from a low-cost halogen lamp, to…
Micro damage and cracking in fibre reinforced composites by a novel hybrid numerical technique
2020
Article number 0033974 AIP Incluida en Conference Proceedings 2309 The prediction of failure mechanisms in fibre-reinforced composite materials is of great importance for the design of composite engineering applications. With the aim of providing a tool able to predict and explain the initiation and propagation of damage in unidirectional fiber reinforced composites, in this contribution we develop a micromechanical numerical model based on a novel hybrid approach coupling the virtual element method (VEM) and the boundary element method (BEM). The BEM is a popular numerical technique, efficient and accurate, which has been successfully applied to interfacial fracture mechanics problems of f…