Search results for "RESISTANCE"
showing 10 items of 3641 documents
Flexural and Shear Resistance of High Strength Concrete Beams
2014
In the present paper, an analytical model is proposed that is able to determine the shear resistance of high strength reinforced concrete beams with longitudinal bars, in the presence of transverse stirrups. The model is based on the evaluation of the resistance contribution due to beam and arch actions. For the resistance contribution of the main bars in tension the residual bond adherence of steel bars and the crack spacing of R.C. beams are considered. The compressive strength of the compressed arch is also verified by taking into account of the biaxial state of stresses. The model was verified on the basis of experimental data available in the literature and it is able to include the fo…
Knock Resistance Increase through the Addition of Natural Gas or LPG to Gasoline: An Experimental Study
2013
Bi-fuel spark ignition engines, nowadays widely spread, are usually equipped with two independent injection systems, in order run the engine either with gasoline or with gaseous fuel, which can be Natural Gas (NG) or Liquefied Petroleum Gas (LPG). These gases, besides lower cost and environmental impact, are also characterized by a higher knock resistance with respect to gasoline that allows to adopt a stoichiometric proportion with air also at full load. Gasoline, on the other hand, being injected as liquid, maintains higher volumetric efficiency and hence higher power output. As a compromise solution, it could be desired to exploit the advantages of both gasoline and gas (NG or LPG), thus…
Thermal and structural properties of a hemp–lime biocomposite
2013
Abstract The need to reduce greenhouse gases emission produced by the building sector leads to the research of renewable and less impacting materials that can replace traditional ones. This subject has encouraged new researches on biocomposite concretes with the aim to exploit renewable resources like vegetal fibres intended as materials whose production processes are generally characterized by low costs and energy demand. This biocomposite is obviously much lighter than concrete and, therefore, can be suitably used in such cases where a structure cannot be overloaded, for instance in the realization of a green covering on top of a preexistent building. In this work, a first analysis of the…
Urban Energy Hubs Economic Optimization and Environmental Comparison in Italy and Vietnam
2018
This paper aims to perform the minimization of the yearly energy supply cost from the main electricity and natural gas grids related to an energy district, considering the installation of different equipments. The case study refers to energy consumption of a medium density urban district and involves the exploitation of different energy sources and devices (photovoltaic systems, electrical energy storage, heat pumps and cogenerators). The analysis of the district energy supply is accomplished through an energy hub model. After a cost analysis related to the considered energy systems, a MILP algorithm was used for the optimization of a cost function and the simulation of various scenarios. M…
CFD Study of an Innovative Catamaran with Asymmetrical Hulls
2013
The purpose of this paper is the study of the shape of catamaran with asymmetrical hulls by both experimental and numerical viewpoint. The experimental study is based on the towing tank tests on a catamaran hulls shape obtained from previous works, showing that the wave resistance is very low produces a lower energy loss and a greater effectiveness. The hulls shape is optimized by the CFD application by force of commercial software, which shows that the reduction of wasted energy is very sensitive to make some changes; in particular three different width of the catamaran are tested and their performances are compared.
Advances in Strain Gauge Measurement on Composite Materials
2010
This article gives an overview on the application of strain gauge techniques to the analysis of the strains in composite materials. The orthotropic behaviour of the composite influences the performance of strain gauges that are calibrated for use on isotropic materials. The article considers therefore the typical topics of the strain gauge technology applied to composites with particular reference to the compensation of thermal output, the measurement of the coefficients of thermal expansion, the determination of the strain and stress state, the influence of the misalignment error, the reinforcement effect, the determination of the stress intensification factor, the analysis of residual str…
The Reinforcement Effect of Strain Gauges Embedded in Low Modulus Material
2013
The reinforcement effect of electrical resistance strain gauges is well-described in the literature, especially for strain gauges installed on surface. This paper considers the local reinforcement effect of strain gauges embedded within low Young modulus materials. In particular, by using a simple theoretical model, already used for strain gauges installed on the surface, it proposes a simple formula that allows the user to evaluate the local reinforcement effect of a generic strain gauge embedded on plastics, polymer composites, etc. The theoretical analysis has been integrated by numerical and experimental analyses, which confirmed the reliability of the proposed model.
Silicate and Hydroxide Concentration Influencing the Properties of Composite Al2O3-TiO2 PEO Coatings on AA7075 Alloy
2021
This work evaluates the effect of sodium meta-silicate pentahydrate (SMS) and potassium hydroxide concentrations on properties of Al2O3-TiO2 coatings produced through plasma electrolytic oxidation in a solution containing 3 g L−1 potassium titanyl oxalate, (PTO), using a unipolar waveform with constant current density. The surface and cross-section characteristics of PEO coatings including morphology, elemental distribution, and phase composition were evaluated using FESEM, EDS, and XRD techniques. Voltage-time response indicated the concentration of SMS and KOH had a significant effect on the duration of each stage of the PEO process. More cracks and pores were formed at the higher concent…
Process parameters and surface treatment effects on the mechanical and corrosion resistance properties of Ti6Al4V components produced by laser powder…
2023
Laser powder bed fusion is one of the additive manufacturing technologies which has developed more rapidly in recent years as it enables the production of very complex geometries. Titanium alloys are among the most popular materials in the aerospace industry thanks to excellent mechanical and corrosion resistance. The corrosion behavior and mechanical properties of samples made of Ti6Al4V and characterized by the geometrical features typical of brackets were investigated taking into account the effects of process parameters on porosity and microstructure. A comparison between the corrosion resistance of samples with complex geometry (3D) and specimens characterized by simple geometry (FLAT)…
Ionic shortcut currents via manifolds in reverse electrodialysis stacks
2020
Abstract Reverse electrodialysis (RED) is a blue energy technology for clean and sustainable electricity harvesting from the mixing entropy of salinity gradients. Recently, many efforts have been devoted to improving the performance of RED units by developing new ion-exchange membranes and by reducing the detrimental phenomena affecting the process. Among these sources of “irreversibility”, the shortcut currents (or parasitic currents) flowing through alternative pathways may affect the process efficiency. Although such phenomena occur in several electrochemical processes (e.g. fuel cells, bipolar plate cells and vanadium redox flow batteries), they have received a poor attention in RED uni…