Search results for "RFA"
showing 10 items of 11106 documents
Comparison of electropolishing behaviours of TSC, ALM and cast 316L stainless steel in H 3 PO 4 /H 2 SO 4
2017
Abstract In recent decades, new manufacturing processes have been developed such as Thermal Spray Coating (TSC) and Additive Layer Manufacturing (ALM), which reduce or avoid machining of parts with complex geometries. This study aims to develop an Electropolishing (EP) process for TSC and ALM 316L Stainless Steel (SS). EP is an anodic dissolution process currently used in industry to reduce surface roughness and obtain a bright and smooth finish. The EP mechanism was studied, in a mixture of H3PO4 and H2SO4, for TSC, ALM and “cast” SS in order to determine the best conditions (time, temperature, potential). Special attention was paid to surface characterization by combining several techniqu…
Effect of active heating and cooling on microstructure and mechanical properties of friction stir–welded dissimilar aluminium alloy and titanium butt…
2019
A butt joint configuration of AA6061–pure Ti was welded using friction stir welding (FSW) with an assisted cooling and heating conditions, aiming to attain a flawless joint. Cooling-assisted friction stir welding (CFSW) was carried out with a different cooling medium such as CO2, compressed air and water at controlled flow rate. However, heating-assisted friction stir welding (HFSW) was performed with heating source of GTAW torch just before FSW tool at different current density. Prepared specimens were subjected to optical microscopy (OM), scanning electron microscopy (SEM) and electrodischarge spectroscopy (EDS) for microstructural characterizations. The tensile strength and microhardness…
A new approach to simulate coating thickness in cold spray
2020
Abstract In the process of cold spray on complex components, the coating thickness is an important indicator to monitor and control. Current methods such as destructive tests or direct mechanical measurements can only be performed after spraying. Besides, these methods lead to production shutdown and additional costs . This article presents a novel approach predicting coating thickness for components with complex curved surfaces, especially in the case of shadow effects. Firstly, a three-dimensional geometric model of the coating profile based on Gaussian distribution was developed. In addition, the relative deposition efficiency (RDE) resulting from the different robot kinematic parameters…
Assessing the influence of fieldshaper material on magnetic pulse welded interface of Al/Cu joints
2019
Abstract Fieldshaper (FS) is a widely used component in magnetic pulse forming and welding to improve the efficiency of the process. It enables to increase the magnetic pressure experienced by the workpieces during forming and welding. Recent developments in this subject focuses to increase the life time of the fieldshaper and to improve the efficiency by introducing shape optimized designs. In this study, we compare the efficiency of four fieldshapers made of Cuprofor, Siclanic, CuBe2 and Steel. The main focus is given to the effect of material properties while the same geometry was considered for those four fieldshapers. The same welding conditions (discharge voltage of 6kV and air gap of…
On the optimization of the cutting conditions for an improved corrosion resistance of OFHC copper
2018
International audience; Machining has a particular impact on the surface integrity and on corrosion resistance of components. In fact, material removal induces geometrical, mechanical and micro-structural modifications in the machined surface and sub-surface that alter the electrochemical behavior of the material, and so the aging process. In this study, oxygen free high conductivity copper (OFHC) has machined under orthogonal cutting conditions using uncoated cemented carbide tools. Then, the corrosion resistance in 0.1 M NaCl salt fog atmosphere of the machined samples is analyzed. Finally, the optimal cutting conditions, including the tool geometry, for an improved corrosion resistance a…
Improving surface integrity of additively manufactured GP1 stainless steel by roller burnishing
2020
Abstract Additive manufacturing can rapidly fabricate the desired components by selectively melting and solidifying feedstock, rather than conventional subtractive machining. However, the difference between the two routes in terms of surface integrity of the final component is relevant. This paper presents a strategy to control the surface characteristics of additively manufactured stainless steel by roller burnishing. In particular, process parameters have been carefully selected to improve the surface integrity of the worked material. The quality of the surface has been analyzed in terms of roughness, hardness, microstructure and residual stresses. The overall product endurance under high…
Influence of residual stress, surface roughness and crystallographic texture induced by machining on the corrosion behaviour of copper in salt-fog at…
2012
International audience; The influence of quadratic stress, crystallographic texture, lubrication and surface roughness generated by superfinish turning on the corrosion behaviour of pure copper was quantified in salt-fog atmosphere. This was done using statistical analysis (Pearson's correlation matrix). Three compounds were found after corrosion tests: atacamite/paratacamite and a black layer (mixture of the lubricant and the salt atmosphere). Surface characteristics were classified according to their decreasing influence on the formation of atacamite/paratacamite as follows: surface roughness and quadratic stress. Lubrication and the crystallographic texture have the lowest influence on c…
Impact des conditions d'usinage sur la zone du matériau affectée par le procédé
2007
Colloque avec actes et comité de lecture. Internationale.; International audience; Les procédés d'usinage peuvent créer des contraintes résiduelles à la surface des pièces usinées et ainsi modifier la microstructure et la texture de la matière proche de la surface. De tels changements sont importants pour l'étude du comportement des pièces au cours du temps. Il est alors nécessaire de quantifier les contraintes résiduelles, les composantes de texture et de déterminer la microstructure induite par l'usinage pour comprendre et prédire le comportement des surfaces considérées. Dans cette étude, le matériau cuivre pur a été choisi et considéré comme un "système modèle". En tournage, l'influence…
Surface Characteristics of Machined Polystyrene with 3D Printed Thermoplastic Tool
2020
An effort is made in this work to appraise the surface characteristics of machined expandable polystyrene (EPS) with a novel 3D printed thermoplastic acrylonitrile-butadiene-styrene (ABS) tool. Linear grooves on EPS were made on a vertical milling machine that was modified to conduct experiments in the laboratory. The tests were designed as per the Taguchi L9 based factorial design of experimentation while varying process parameters such as depth of cut, spindle speed, and feed rate. The machining responses dimensional accuracy and surface roughness of the machined grooves were studied. Furthermore, the surface topography of the machined specimens was considered to investigate the mechanism…
Optimisation of refractory coatings realised with cored wire addition using a high-power diode laser
2005
Laser; Cladding; Refractory alloys; Factorial experiments; International audience; The objective or our research was to obtain refractory alloys using the high-power diode laser (HPDL) coating technique. After optimisation using factorial experiments, two different cladding regimes were clearly distinguished. It was also shown that a very narrow transition zone exists between the two regimes, and, inside this zone, clad layers having a satisfactory compromise between the response functions (surface aspect and cavity presence) were obtained. The main objective of our study, namely, the control of the operating parameters (geometrical and kinematical) to realise adequate coatings, without cav…