Search results for "Ranging"
showing 10 items of 80 documents
Analysis and Evaluation of Adaptive RSSI-based Ranging in Outdoor Wireless Sensor Networks
2019
Estimating inter-node distances based on received radio signal strength (RSSI) is the foundation of RSSI-based outdoor localization in wireless sensor networks (WSNs). However, the accuracy of RSSI-based ranging depends on environmental and weather conditions. Therefore, it is important that RSSI-based ranging adapts to prevailing conditions to improve its range and location accuracy. This paper analyzes and evaluates RSSI-based ranging and adaptive techniques in outdoor WSNs to improve the range quality. The findings highlight the effects of path loss exponent (PLE) estimation error and temperature change on RSSI-based ranging. Consequently, we analyze techniques for mitigating these detri…
Indoor localization using time difference of arrival with UWB signals and unsynchronized devices
2020
Abstract Indoor location using radio frequency (RF) signals has been traditionally focused mainly on RSSI and fingerprint techniques, because methods based on time of arrival (ToA) or time difference of arrival (TDoA) were not suitable for measuring short distances. However, the release of the IEEE 802.15.4a standard, the emergence of commercial ultra wide band (UWB) transceivers that are compliant to this norm and the integration of high frequency oscillators have permitted the design of more accurate indoor localization systems using the RF signal transmission time. In this paper, we propose an indoor localization system based on TDoA for UWB. The method implements an only one way transmi…
Methodologies for the Exploitation of Existing Energy Corridors. GIS Analysis and DTR Applications
2018
The exploitation of power lines currently in operation has now become a common practice among electric system operators. The construction of new power lines requires taking economic, political and social problems into consideration. This paper considers two methodologies adopted by the Italian Transmission System Operator (TSO), Terna S.p.A.: Dynamic Thermal Rating (DTR) and Laser Imaging Detection and Ranging-Geographic Information System (L-GIS). DTR systems dynamically calculate the real transport capacity of a power line. The L-GIS system allows, after the geo-referencing of the power line, the management of any interference between the line and the nearby obstacles, permitting the opti…
Earth's Surface Displacements from the GPS Time Series
2015
The GPS observations of both Latvian permanent GNSS networks - EUPOS®-Riga and LatPos, have been collected for a period of 8 years - from 2007 to 2014. Local surface displacements have been derived from the obtained coordinate time series eliminating different impact sources. The Bernese software is used for data processing. The EUREF Permanent Network (EPN) stations in the surroundings of Latvia are selected as fiducial stations. The results have shown a positive tendency of vertical displacements in the western part of Latvia - station heights are increasing, and negative velocities are observed in the central and eastern parts. Station vertical velocities are ranging in diapason of 4 mm/…
First results of iButton® loggers and infrared camera application inside a greenhouse
2017
Greenhouse microclimate management (temperature, relative humidity) plays a very important role in order to optimize the production process improving pest and disease control, irrigation and energy efficiency. The systems mostly used in Sicily (south Italy) to record the ambient parameters are made up of fixed measuring stations able to give useful information about the climate inside the greenhouse limited to some pre-fixed points. In this study we texted a novel system made up of humidity and temperature data loggers (iButton®) placed inside a greenhouse. The iButton® temperature/humidity logger (DS1923) is a rugged, self-sufficient system that measures temperature and/or humidity and r…
Experimental Demonstration of 50-Mb/s Visible Light Communications Using 4<inline-formula> <tex-math notation="TeX">$\,\times\,$ </tex…
2014
This letter reports the experimental demonstration of an indoor visible light nonimaging multiple-input multiple-output system with an aggregate error free bit rate of 50 Mb/s over a distance of 2 m. The system uses four independent white LED transmitters, each transmitting 12.5 Mb/s of data in the ON-OFF keying nonreturn zero format, and four independent nonimaging optical receivers. The performance of four detection methods ranging from the basic channel inversion to the more advanced space time techniques is compared experimentally. The results gathered demonstrate that the simplest technique is capable of the same bit error rate as the most complex scheme. The system also provides full …
The mechanics of continuous chip formation in oblique cutting with single-edged tool—part II. Experimental verification of the theory
1990
Abstract Experimental results obtained during oblique cutting of annealed steel Ck 45 (SAE-AISI 1045) with a single-edged tool are presented. Extensive measurements of forces, cutting ratio, chip flow angle etc. have been carried out under a wide range of cutting conditions. The measured data obtained from these cutting tests are used to test assumptions proposed in the first part of this work. In relation to previous works dealing with oblique cutting problems the present one extends to tools with angles of tool obliquity ranging from 30° to 70° and having a large negative rake angle.
Investigation of flow and heat transfer in corrugated passages—II. Numerical simulations
1996
An experimental and numerical study of flow and heat transfer was conducted for a crossed-corrugated geometry, representative of compact heat exchangers under transitional and weakly turbulent conditions. Three-dimensional numerical predictions were obtained by a finite volume method using a variety of approaches ranging from laminar flow assumptions to standard and low-Reynolds number k-e turbulence models, direct simulation, and large-eddy simulation. In this paper, the various computational approaches are presented and their relative performance is discussed for various geometries and Reynolds numbers; results are compared with experimental measurements and literature data. Detailed expe…
An efficient method for fully automatic 3D digitization of unknown objects
2013
Our goal is to develop a complete and automatic scanning strategy with minimum prior information about the object shape. We aim to establish a methodology for the automation of the 3D digitization process. The paper presents a novel approach to determine the Next Best View (NBV) for an efficient reconstruction of highly accurate 3D models. Our method is based on the classification of the acquired surfaces into Well Visible and Barely Visible combined with a best view selection algorithm based on mean shift, which avoids unreachable positions. Our approach is applicable to all kinds of range sensors. To prove the efficiency and the robustness of our method, test objects are first scanned man…
The Near Real Time Ionospheric Model of Latvia
2015
A highly accurate ionosphere model is necessary to enable a fast and reliable coordinate determination with GNSS in real time. It is a partially ionized atmospheric region ranging up to 1,000 km height, affected by spatial variations, space weather, seasonal and solar cycle dependence. New approaches and algorithms of modelling techniques are sought to provide better solutions in the territory of Latvia. Ionospheric TEC value has large differences in Western Latvia and Eastern Latvia. Actual ionospheric map should be calculated and delivered to the surveyors near real time and published on the WEB. Delivering actual map to rover GNSS devices in a field will provide the surveyors with ionosp…