Search results for "Renewable"
showing 10 items of 2395 documents
Researches on the Alternative Fuels Which Can Be Used to Motors
2010
The alternative fuels are substances or materials used as fuel, other than the old conventional fuels (oil, natural gases and coals). 
 The paper analyses the most important alternative fuels, such as: bio-diesel, alcohols and hydrogen, presenting at each category the main important characteristics, the advantages and disadvantages presented by them. 
 The methyl-ester which is known as bio-diesel can be used in all motors with ignition by compression, alone or mixed in any proportion with oil, with minor modifications at the injection system. Bio-diesel fuel assures the same motor power as oil does, having even a bigger cetanic number than the usual oil. After tests, it was obser…
Modeling of copper fixed-bed biosorption from wastewater by Posidonia oceanica
2009
Biosorption of copper from aqueous solutions by Posidonia oceanica was investigated in batch and fixed-bed experiments. Batch experiments were conducted to evaluate the removal equilibrium at pH 5.0 and 6.0; experimental data were fitted to Langmuir model with maximum uptake capacities of 56.92 and 85.78 mg g(-1), respectively. Five column experiments were carried out at different feed concentrations. Breakthrough times and continuous sorption isotherm were obtained from breakthrough curves. Differences among batch and continuous isotherms were observed; the maximum uptake capacity in dynamic conditions was found in 56.70 mg g(-1) for final pH between 5.0 and 5.5. The biosorbent was regener…
An improved cathode for alkaline fuel cells
2010
Abstract The use of nickel foam as an electrode substrate in alkaline fuel cells (AFCs) has been investigated for bipolar cells incorporating an electrically conducting gas diffusion layer (GDL). Improved performance, compared to a previous design, was obtained by adding an extra active layer (AL) composed of manganese (IV) oxide (MnO2) deposited onto carbon black. This new cathode design performed significantly better (130 mA cm−2 at 0.8 V and 25 °C) than the previous design (35 mA cm−2 under the same condition), especially at higher potential. It has been shown that the GDL is a key component of the gas diffusion electrode for both performance and durability, especially with liquid electr…
Alkaline fuel cell technology - A review
2021
Abstract The realm of alkaline-based fuel cells has with the arrival of anionic exchange membrane fuel cells (AEMFCs) taken a great step to replace traditional liquid electrolyte alkaline fuel cells (AFCs). The following review summarises progress, bottleneck issues and highlights the most recent research trends within the field. The activity of alkaline catalyst materials has greatly advanced, however achieving long-term stability remains a challenge. Great AEMFC performances are reported, though these are generally obtained through the employment of platinum group metals (PGMs), thus emphasising the importance of R&D related to non-PGM materials. Thorough design strategies must be utilise…
Favoring alkane primary carbon-hydrogen bond functionalization in supercritical carbon dioxide as reaction medium
2019
The selectivity of a catalytic alkane functionalization process can be modified just changing the reaction medium from neat alkane to supercritical carbon dioxide (scCO2). A silica supported copper complex bearing an Nheterocyclic carbene ligand promotes the functionalization of carbon-hydrogen bonds of alkanes by transferring the CHCO2Et group from N2=CHCO2Et (ethyl diazoacetate, EDA). In neat hexane only 3% of the primary C-H bonds (ethyl heptanoate being the product) are functionalized in that manner, whereas the same reaction carried out in scCO2 provides a 30% yield in this linear ester. Such effect seems to be induced by an electronic density flux from the NHC ligand to the surroundin…
Influence of melt flow and temperature on erosion of refractory and deposit formation in aluminium melting furnaces
2002
The deposition and erosion mechanism in induction-channel furnace for Al melting in alumino-silicate refractory is considered. The possibility of simultaneous erosion and deposition in the same cross-section of the channel is shown. The chemical reaction model causing the erosion of refractory is proposed. The erosion process is described by chemically active aluminium oxides while the deposition is caused by chemically stable aluminium oxides. The variations of erosion and deposition in the same cross-section of the channel are explained by variation of the thickness of laminar sub-layer along the perimeter.
The Effect of Electronic Properties of Anodized and Hard Anodized Ti and Ti6Al4V on Their Reactivity in Simulated Body Fluid
2022
The electronic properties of barrier and porous layers on Ti and Ti6Al4V were studied. Barrier anodic oxides grown to 40 V on Ti and on Ti6Al4V are both n-type semiconductors with a band gap of 3.3 eV and 3.4 eV respectively, in agreement with the formation of amorphous TiO2. Anodizing to 200 V at 20 mA cm−2 in calcium acetate and β-glycerol phosphate disodium pentahydrate leads to the formation of Ca and P containing porous films with a photoelectrochemical behaviour dependent on the metallic substrate. A band gap of 3.2 eV and the flat band potential of −0.5 V vs Ag/AgCl were measured for the porous oxide on Ti, while optical transitions at 2.15 eV and a significantly more positive flat b…
A qualitative examination of performance and energy yield of photovoltaic modules in southern Norway
2010
Three different, commercially available photovoltaic modules have been monitored outdoors in the town of Grimstad, Norway. The present paper describes the experimental setup that was implemented, in particular details of the low-cost electronic loads. Results compare measured performance with manufacturer's data, and temperature measurements enable a comparison with performance at standard test condition temperature. Overall, the monocrystalline module performed best both regarding maximum efficiency and overall energy production, whereas the module based on triple junction amorphous silicon technology had the worst performance considering these criteria. The gross numbers of energy yield c…
A procedure to evaluate the seven parameters of the two-diode model for photovoltaic modules
2019
Abstract The paper presents an analytical procedure to calculate the seven parameters of the two-diode model of photovoltaic (PV) panels for any value of the solar irradiance and cell temperature. Six parameters (the photocurrent, the diode reverse saturation currents, the quality factor of the first diode and the series and shunt resistances), are evaluated by solving the equations related to the properties of the main points of the current-voltage (I-V) characteristics. The further information, necessary to calculate the entire set of seven truly independent parameters, is based on two conditions that have to be simultaneously satisfied: 1) the exclusion of negative values of the model pa…
Comparison between textured SnO2:F and Mo contacts with the p-type layer in p–i–n hydrogenate amorphous silicon solar cells by forward bias impedance…
2013
Abstract In this paper we compare the performance of the textured SnO2:F and Mo contacts with the p-type layer in p–i–n hydrogenate amorphous silicon (a-Si:H) solar cells. We use standard current–voltage (I–V) electrical characterization methods coupled with forward bias small signal impedance analysis. We show the efficacy of this technique to determine the effective carrier lifetime in photovoltaic cells. We show that such effective lifetimes are indeed directly connected to the respective dark diode saturation currents. We also find that the effective lifetime is constant with the temperature in the 0–70 °C range and it is significantly better for the solar cell with Mo diode contact. Th…