Search results for "Residual stre"
showing 10 items of 125 documents
On the self-piercing riveting of aluminium blanks and carbon fibre composite panels
2010
In the present paper the possibility to join aluminium alloys blanks and carbon fibre composites panels by self-piercing riveting operation is considered. In particular a few case studies were carried out at the varying of the process parameters. The effectiveness of the obtained joints was tested through tensile tests and through fatigue ones; what is more the process mechanics was highlighted through proper macro and micro observations of the transverse sections of the joints. The failure mechanics of the obtained joints were also considered in order to highlight the mechanisms which occur and determine the lost of the load carrying capability of the joints. Finally a numerical model of t…
Elastic configurations of self-supported oxide membranes for fuel cells
2013
Abstract Ultra-thin oxide films are of interest in energy conversion technologies such as low temperature solid oxide fuel cells and permeation membranes. Understanding their thermo-mechanical stability is an important problem. Edge clamped, self-supported thin film membranes show hierarchical wrinkles; with the largest wavelengths in the center, while smaller ones arise near the clamped boundary; correspondingly the largest strains, with tensile stress comparable to the residual stress, are in the vicinity of the clamped boundary. Our results can be understood by simple scaling arguments and are valid for membranes in the post-buckling regime far from threshold. We confirm the validity of …
Aluminum oxide from trimethylaluminum and water by atomic layer deposition:The temperature dependence of residual stress, elastic modulus, hardness a…
2014
Use of atomic layer deposition (ALD) in microelectromechanical systems (MEMS) has increased as ALD enables conformal growth on 3-dimensional structures at relatively low temperatures. For MEMS device design and fabrication, the understanding of stress and mechanical properties such as elastic modulus, hardness and adhesion of thin film is crucial. In this work a comprehensive characterization of the stress, elastic modulus, hardness and adhesion of ALD aluminum oxide (Al2O3) films grown at 110-300 C from trimethylaluminum and water is presented. Film stress was analyzed by wafer curvature measurements, elastic modulus by nanoindentation and surface-acoustic wave measurements, hardness by na…
Residual stress and material flow prediction in Friction Stir Welding of Gr2 Titanium T-joints
2022
Friction Stir Welding is nowadays an established technique successfully used by many industries. However, most of the research and, consequently, most of the applications regard aluminum alloys and butt joints. T-joints are of high interest for different industrial sectors as aeronautical, aerospace, naval and ground transportation, for which joint integrity and low residual stress are extremely important. In this study, an experimental and numerical approach is proposed with the aim to study the peculiarities of the residual stress distribution and material flow occurring in FSW of CP-Ti T-joints. Experiments were carried out to assess the feasibility of the process and to acquire the temp…
Investigating the effect of residual stress on hydrogen cracking in multi-pass robotic welding through process compatible non-destructive testing
2021
Abstract In this paper, the effect of Welding Residual Stress (WRS) on the size and morphology of hydrogen-induced cracks (HIC) is studied. Four samples were manufactured using a 6-axis welding robot and in two separate batches. The difference between the two batches was the clamping system used, which resulted in different amounts of welding deformation and WRS. The hydrogen cracks were intentionally manufactured in the samples using a localised water-quenching method, where water was sprayed over a specific weld pass in a predetermined position. The Phased-Array Ultrasonic Testing (PAUT) system was implemented during the welding process (high-temperature in-process method), to detect the …
In situ and postradiation analysis of mechanical stress in Al2O3:Cr induced by swift heavy-ion irradiation
2010
Abstract Optical spectroscopy and TEM techniques have been applied to study the radiation damage and correlated mechanical stresses in Al2O3 and Al2O3:Cr single crystals induced by (1–3) MeV/amu Kr, Xe and Bi ion irradiation. Mechanical stresses were evaluated in situ using a piezospectroscopic effect through the shift of the respective lines in ionoluminescence spectra. It was found that dose dependence of the stress level for Xe and Bi ions, when ionization energy loss exceeds the threshold of damage formation via electronic excitations, exhibits several alternate stages showing the build-up and relaxation of stresses. The beginning of relaxation stages is observed at fluences associated …
Measurement of edge residual stresses in glass by the phase-shifting method
2011
Abstract Control and measurement of residual stress in glass is of great importance in the industrial field. Since glass is a birefringent material, the residual stress analysis is based mainly on the photoelastic method. This paper considers two methods of automated analysis of membrane residual stress in glass sheets, based on the phase-shifting concept in monochromatic light. In particular these methods are the automated versions of goniometric compensation methods of Tardy and Senarmont. The proposed methods can effectively replace manual methods of compensation (goniometric compensation of Tardy and Senarmont, Babinet and Babinet–Soleil compensators) provided by current standards on th…
Photoelastic Analysis of Edge Residual Stresses in Glass by Automated “Test Fringes” Methods
2011
Since the glass is a birefringent material, the analysis of residual stress in glass is usually carried out by means of photoelastic methods. This paper considers the automation of the “test fringes” method which is based on the use of a Babinet compensator or of a beam subjected to bending. In particular, two automated methods are proposed: the first one is based on the use of the centre fringe method in monochromatic light and the second one is based on the use of RGB photoelasticity in white light. The proposed methods have been applied to the analysis of membranal residual stresses in some tempered glasses, showing that they can effectively replace manual methods of photoelastic analysi…
RGB photoelasticity applied to the analysis of membrane residual stress in glass
2011
The measurement of residual stresses is of great relevance in the glass industry. The analysis of residual stress in glass is usually made by photoelastic methods because glass is a photoelastic material. This paper considers the determination of membrane residual stresses in glass plates by automatic digital photoelasticity in white light (RGB photoelasticity). The proposed method is applied to the analysis of membrane residual stresses in some tempered glass. The proposed method can effectively replace manual methods based on the use of white light, which are currently provided by some technical standards.
A critical assessment of automatic photoelastic methods for the analysis of edge residual stresses in glass
2014
The measurement of residual stresses is of great importance in the glass industry. The analysis of residual stresses in the glass is usually carried out by photoelastic methods since the glass is a photoelastic material. This article considers the determination of membrane residual stresses of glass plates by digital photoelasticity. In particular, it presents a critical assessment concerning the automated methods based on gray-field polariscope, spectral content analysis, phase shifting, RGB photoelasticity, “test fringes” methods and “tint plate” method. These methods can effectively automate manual methods currently specified in some standards.