Search results for "Retention"
showing 10 items of 347 documents
A multinjection strategy for mercury speciation.
2005
Abstract A multiinjection strategy has been developed to increase the sampling throughput of the high-performance liquid chromatography determination of inorganic-mercury, methylmercury, ethylmercury and phenylmercury. The method involves the injection of samples each 3.5 min, in spite of the fact that phenylmercury retention time corresponds to 9.04 min. In the selected conditions, the sampling frequency was 11 h −1 in front of that of 6 h −1 , obtained by conventional injection of each sample after the complete elution of Hg species. Additionally, the analytical reagents consumption was reduced drastically in almost 50%. The main characteristics of the chromatographic separation were main…
Retention increments of isomeric chlorobenzenes
1983
The chlorobenzene isomers are used extensively as intermediates in a wide range of chemical products. More recently their determination in environmental situations has become of considerable importance and chromatographic procedures have been widely reported for their determination in both trace and major amounts. There are over 220 publications in which gas chromatography (GC) has been applied to the analysis of chlorobenzene. However, over 60 o/o of these works refer to the separation of only one isomer. Relatively few publications’-8 consider all the isomers, although the use of both capillary3’ and packedcolumns with polar and non-polar stationary phases has been reported. Temperature p…
Reliability of the retention factor estimations in liquid chromatography.
2004
The retention factor is one of the most universally used parameters in chromatography. However, large differences in the experimental retention factor values are observed when the same compound is injected in a given stationary/mobile phase system under intermediate precision conditions. Conventional protocols for estimating retention factors have problems that mainly arise from difficulties in the hold-up time measurements and the omission of the existence of extra-column times by practicing chromatographers. In the present paper, three different approaches for estimating retention factors are tested: (i) classical retention factor estimations based on the gross hold-up time, (ii) based on…
On the Measurement of Dead Time in Micellar Liquid Chromatography
1996
Abstract Modelling of the retention of solutes in micellar liquid chromatography allows the optimization of the resolution of a mixture of solutes and the determination of physico-chemical retention parameters. Both tasks imply the calculation of capacity factors, which are severely affected by the value of dead time. However, the determination of the dead time is not easy when a micellar mobile phase is used owing to the wide and variable perturbations that appear at the heads of the chromatograms. Four different criteria of determination of a reference time in the chromatograms are proposed and compared. The criteria are applied to mobile phases containing a varying concentration of surfa…
H-point standard additions method for resolution of overlapped chromatographic peaks with a conventional fluorescence detector. Determination of phen…
1996
The H-Point Standard Additions Method (HPSAM) is proposed in order to resolve overlapping peaks in liquid chromatography by using a conventional fluorescence detector. The method uses as analytical signals the heights or the areas obtained at two previously selected emission wavelengths, and good results are obtained for highly overlapping peaks with highly overlapping fluorescence spectra. The principal benefits of the method are the ease of finding the required wavelengths, its insensitivity to changes in the retention time of the peak from one injection to another, and the possibility of using it in highly or only partially overlapping peaks. We have applied the method to the determinati…
Description of the Retention and Peak Profile for Chromolith Columns in Isocratic and Gradient Elution Using Mobile Phase Composition and Flow Rate a…
2014
The effect of the modifier concentration and flow rate on the chromatographic performance of a second generation Chromolith® RP-18e column, under isocratic and gradient elution with acetonitrile-water mixtures, was examined using four sulphonamides as probe compounds. The acetonitrile concentration was varied between 5 and 55% (v/v), and the flow rate between 0.1 and 5.0 mL/min, keeping the other factors constant. The changes in both retention and peak profile were modelled, and used to build simple plots, where the logarithm of the retention factor was represented against the modifier concentration (in gradient elution, against the initial modifier concentration), and the half-widths or wi…
Biopartitioning micellar chromatography to pedict mutagenicity of aromatic amines
2007
[EN] Mutagenicity is a toxicity endpoint associated with the chronic exposure to chemicals. Aromatic amines have considerable industrial and environmental importance due to their widespread use in industry and their mutagenic capacity. Biopartitioning micellar chromatography (BMC), a mode of micellar liquid chromatography that uses micellar mobile phases of Brij35 in adequate experimental conditions, has demonstrated to be useful in mimicking the drug partitioning process into biological systems. In this paper, the usefulness of BMC for predicting mutagenicity of aromatic amines is demonstrated. A multiple linear regression (MLR) model based on BMC retention data is proposed and compared wi…
Gas—liquid chromatographic analyses
1985
Abstract The gas chromatographic retention behaviour of methylethyl, 1-methylpropyl, 2-methylpropyl, 1,2-dimethylpropyl, 1-methylbutyl and 3-methylbutyl esters of benzoic and o-, m- and p-chlorobenzoic acids on low-polarity (SE-30) and polar (OV-351) capillary columns under several temperature-programmed and isothermal conditions is reported. The retention data and the Kovats retention indices for all 24 components are given and the separation of a complex mixture is discussed. The retention index increments have been used to examine the effects of chain branching and chlorine substitution. The results are compared with those for n-alkyl benzoates and monochlorobenzoates.
Anaerobic thermophilic (55°C) treatment of TMP whitewater in reactors based on biomass attachment and entrapment
1999
Abstract Thermomechanical pulping (TMP) whitewater was treated in thermophilic (55°C) anaerobic laboratory-scale reactors using three different reactor configurations. In all reactors up to 70 % COD removals were achieved. The anaerobic hybrid reactor, composed of an upflow anaerobic sludge blanket (UASB) and a filter, gave degradation rates up to 10 kg COD/m 3 d at loading rates of 15 kg COD/m 3 d and hydraulic retention time (HRT) of 3.1 hours. The anaerobic multi-stage reactor, consisting of three compartments, each packed with granular sludge and carrier elements, gave degradation rates up to 9 kg COD/m 3 d at loading rates of 15–16 kg COD/m 3 d, and HRT down to 2.6 hours. Clogging and …
Start-up with or without inoculum? Analysis of an SMBR pilot plant.
2010
This study analysed a submerged membrane bioreactor (SMBR) start-up with the purpose of determining the best conditions to carry it out. In order to do this, a hollow fibre membrane module was installed in a submerged configuration in a pilot aerobic reactor. The experiment was then divided in two phases, lasting 65 days each. During phase 1, the pilot plant was started-up without inoculum of activated sludge and no sludge, withdrawal was performed. Conversely, in phase 2, the MBR pilot plant was started-up with sludge inoculum and the sludge concentration was kept constant. In both phases, the volumetric loading rate applied to the pilot plant was kept constant. The authors analysed the di…