Search results for "Rotational speed"
showing 10 items of 28 documents
On the assessment of power consumption and critical impeller speed in vortexing unbaffled stirred tanks
2017
Abstract Unbaffled stirred tanks are increasingly recognized as a viable alternative to common baffled tanks for a number of processes and bio-processes where the presence of baffles is undesirable. Notwithstanding the increasing industrial interest towards unbaffled tanks, available experimental information on their behaviour is still very poor, even for important parameters such as mechanical power drawn and critical impeller speed (Ncr) at which the transition between non-aerated (sub-critical regime) and aerated (super-critical regime) conditions occurs. In this work the influence of Reynolds and Froude numbers on power consumption characteristics of unbaffled stirred tanks is presented…
Control of hysteretic instability in rotating machinery by elastic suspension systems subject to dry and viscous friction
2010
Abstract Most of the undesired whirling motions of rotating machines can be efficiently reduced by supporting journal boxes elastically and controlling their movement by viscous dampers or by dry friction surfaces normal to the shaft axis, which rub against the frame. In the case of dry dampers, resonance ranges of the floating support configuration can be easily cut off by planning a motionless adhesive state of the friction surfaces. On the contrary, the dry friction contact must change automatically into sliding conditions when the fixed support resonances are to be feared. Moreover, the whirl amplitude can be restrained throughout the speed range by a proper choice of the suspension-to-…
Friction stir consolidation of aluminum machining chips
2017
Friction stir consolidation (FSC) is a solid-phase manufacturing process that consolidates metal powder, chips, or scraps into solid blocks via severe plastic deformation and solid state welding. It has the potential to be a more economical and âgreenâ process to recycle metal waste. In this study, solid discs were made from AA6061 aluminum alloy machining chips by FSC. The progression of the process was revealed by analyzing the motion of the tool, consolidating force, power history, and macro/microstructure of discs produced from a series of partial consolidation experiments. A bowl-shaped recrystallized zone in the vertical cross-sections of the disc products was observed and conside…
Damping of rotor conical whirl by asymmetric dry friction suspension
2009
Abstract A new technique for the rotor whirl damping in rotating machinery, based on the elastic suspension of the journal boxes and the use of dry friction surfaces normal to the shaft axis between their supports and the frame, is here analysed theoretically for several cases of rotor systems characterized by mass and constraint asymmetry, where gyroscopic effects are to be expected and conical whirl motions may grow up. The critical flexural speeds can be easily cut off by an adhesive state of the supports and the whirl amplitude can be minimized as well throughout the remaining sliding range. Confining the operative angular speed of the rotor in the range of adhesive contact between the …
Friction stir welding of lap joints: Influence of process parameters on the metallurgical and mechanical properties
2009
Abstract Aluminum alloys are widely used in the aircraft industries even if such materials present lower ductility with respect to steels, anisotropy phenomena and, more important, they are often “difficult” to be welded or even “non-weldable”. In the last years the friction stir welding process (FSW) was proposed and applied in order to get good mechanical and technological performances of the joints. In this paper, an experimental and numerical investigation on the lap joining of AA2198-T4 aluminum alloy blanks by FSW is presented. In particular the joints strength and metallurgical properties are investigated by varying the joint configuration and the tool geometry and rotational speed. …
Research on the electrostatic properties of liquid dielectric mixtures
2007
Abstract This paper presents research results, which confirm the possibility of influencing the electrostatic charge tendency (ECT) of selected mixtures of purely insulating liquids. Tests were performed in a spinning disk system, where the factors influencing the value of the electrification current consisted of variable composition of the toluene–cyclohexane mixture, rotational speed, and a disk diameter. Liquid hydrocarbon mixtures displayed changes in ECT as well as classic insulation parameters such as resistivity and relative permittivity for concentration changes of the admixtures. These results can be used to assist the search for inhibitors of ECT and of aging processes in insulati…
A Rotor Flux and Speed Observer for Sensorless Single-Phase Induction Motor Applications
2012
It is usual to find single-phase induction motor (SPIM) in several house, office, shopping, farm, and industry applications, which are become each time more sophisticated and requiring the development of efficient alternatives to improve the operational performance of this machine. Although the rotor flux and rotational speed are essential variables in order to optimize the operation of a SPIM, the use of conventional sensors to measure them is not a viable option. Thus, the adoption of sensorless strategies is the more reasonable proposal for these cases. This paper presents a rotor flux and rotational speed observer for sensorless applications involving SPIMs. Computer simulations and the…
In-process tool force and rotation variation to control sheet thickness change in friction stir welding of magnesium alloys
2016
Two different in-process control strategies, developed in order to produce sound joints in AZ31 magnesium alloy by Friction Stir Welding on sheet blanks with a non-uniform thickness, are presented and compared. To this purpose, sheets with dip or hump were machined and welded by either changing the rotational speed or the tool plunging in order to keep constant the vertical force occurring during welding. The mechanical strength of the joints was measured in the zones where the sheets before welding were characterised by different thicknesses. The sheets welded by the two different strategies are characterized by very similar ultimate tensile strength values. Finally, the results showed tha…
An experimental study of double-to-single-loop transition in stirred vessels
1999
The velocity characteristics of the flows in a fully baffled vessel of diameter T = 290 mm stirred by a Rushton impeller of diameter D = T/3 were investigated by means of laser-Doppler anemometry measurements. The effects of clearance and rotational speed on the flow patterns in the vessel were studied. It was found that at impeller clearances from the bottom of the vessel (C) around 0.2 T the characteristic double-loop flow pattern undergoes a transition to a single-loop one with the impeller stream direction becoming partly axial and being inclined at around 25 to 30° to the horizontal. The impeller stream inclination varied with radial distance from the impeller, as well as with angular …
Analysis of factors determining thermal changes at osteotomy site in dental implant placement - An in-vitro study
2021
Background Heat generation during osteotomy site preparation is a crucial factor that determines the success of dental implant placement. Among the factors that affect the heat generation, drilling speed, hand pressure and coolant temperature are independent variables. However, a relation between these three parameters and their optimal values required for the maximum outcome has not been studied so far. This study aims at finding out a relation between these factors in order to derive the optimum balance required, using an in vitro study. Material and methods This in vitro experiment was performed on bovine femur. A total of 72 drillings were undertaken with the aid of a physiodispenser mo…