Search results for "Roth"
showing 10 items of 806 documents
Characteristics of LiFePO4 obtained through a one step continuous hydrothermal synthesis process working in supercritical water
2009
International audience; The olivine-like material LiFePO4 was prepared via a continuous hydrothermal synthesis process working from subcritical to supercritical water conditions. The influence of some processing parameters–temperature and reaction time–was investigated in terms of material purity, grain size and morphology. Supercritical conditions were found to be attractive to synthesize in one step a well-crystallized material without impurities. The primary particles size was in the nanometric range. They showed a natural tendency to form micron size agglomerates, which were supposed to be the cause of the limited capacity, as demonstrated through a cross study using laser particle size…
Hygrothermal ageing of reprocessed polylactide
2012
[EN] The influence of an accelerated hygrothermal ageing simulation test on a commercial PLA and its three subsequent mechanically-reprocessed materials was studied. The analysis was focused on the water diffusion kinetics and the physico-chemical changes induced by the hygrothermal degradation. Water diffusion proceeded faster than chain relaxation processes, as defined by a Case II absorption model. It was proved that the water diffusion rate decreased with subsequent reprocessing cycles and increased with higher hygrothermal ageing temperatures. Hydrolytic chain scission provoked significant molar mass decays and consequent general losses of thermal and mechanical performance. The rearra…
Synthesis of self-assembled α-GaOOH microrods and 3D hierarchical architectures with flower like morphology and their conversion to α-Ga2O3
2015
Abstract This report reveals the methodology for the fabrication of α-GaOOH micro rods and micro flowers from gallium nitrate with two different complexing agents. α-GaOOH self-assembled 3D hierarchical architecture, comprising of nanorods and nanoribbbons with a flower like morphology, is fabricated under benign hydrothermal conditions. Calcination of α-GaOOH results in formation of α-Ga 2 O 3 with the retention of morphology. Both gallium oxyhydroxide and gallium oxide microstructures were analyzed with SEM, EDX, TEM and powder X-ray diffraction. α-Ga 2 O 3 micro flowers are furnished with nanorods having ordered diamond like cross section with a diagonal length proportion of 2:1. The hyd…
Particle size and morphology control of the negative thermal expansion material cubic zirconium tungstate
2009
Cubic ZrW2O8 is a negative thermal expansion (NTE) material that is of interest as filler in controlled thermal expansion composites. It is easily accessible from a hydrated precursor, ZrW2O7(OH)2·2H2O, which can be obtained by hydrothermal synthesis. Different reaction conditions were investigated to gain control over the morphology, and to minimize the particle size. Optimized procedures resulted in rod-shaped particles with widths of 10–30 nm and lengths of 200–500 nm, which showed little agglomeration. The particle size and morphology of the precursor are preserved during conversion to the NTE phase at 600–650 °C.
Effect of surface impurities on downconversion luminescence of Pr3+, Yb3+ activated SrF2 nanoparticles
2020
Abstract Pr3+,Yb3+ activated SrF2 nanoparticles synthesized by low-temperature hydrothermal method were studied. The composition and size of nanoparticles were intentionally changed by controlling synthesis conditions. After structural and morphological characterization, the spectroscopic properties of the nanoparticles were analyzed in the visible and near infrared spectra ranges. The results show correlation between the gradual change of the amount of carboxylate and hydroxyl moieties on the nanoparticle surface, varied by the size nanoparticles and the quenching of the luminescence. The size-related amount of surface quenchers is strongly connected to the decrease of the downconversion e…
Synthesis of Titanate Nanotubes Directly Coated with USPIO in Hydrothermal Conditions: A New Detectable Nanocarrier
2011
International audience; Abstract: For the first time, titanate nanotubes (TiONts) coated with USPIO (ultrasmall superparamagnetic iron oxide) without polymer functionalization and directly obtained during TiONts formation is reported. The coating of these tubes was performed directly during the TiONts hydrothermal synthesis. After this treatment, in strongly basic conditions, USPIO particles kept their structure and magnetic properties while their size distribution slightly increased. By coupling zeta-potential measurements and TEM observations at different pH it appeared that interactions between nanotubes and USPIO were not electrostatic. This study presents the new design of a titanate n…
Fracture Toughness of Hydrothermally Aged Epoxy Systems with Different Crosslink Density
2015
Abstract The present work investigates the fracture toughness behaviour of Single Edge Notched Bending (SENB) samples of epoxy systems subject to water uptake aging. Two epoxy systems with a significantly different Glass Transition Temperature, T g , are in particular considered: a typical commercial non-aeronautical grade resin matrix for composite applications, reaching a T g of 90 °C, and a DGEBA+DDS epoxy system achieving a T g of 230 °C.The materials have been conditioned by hydrothermal aging in a thermal bath at the temperature of 50 °C. TransmissionPhotoelastic Stress Analysisis carried outon SENB samples during water aging, monitoring the presence and evolution of swelling stresses…
Preparation of Catalysts and Photocatalysts Used for Similar Processes
2019
Abstract This chapter reports the main techniques used to synthesize powders and films of heterogeneous catalysts and photocatalysts, often used for similar processes. Traditional preparation processes of bulky (photo)catalysts including precipitation, sol–gel technique, hydrothermal or solvothermal method, solid-state reactions, and flame syntheses were briefly described. The sonochemical method and microwave irradiation technique were also considered. The syntheses of supported catalysts by different techniques, including deposition–precipitation, impregnation, and wet coating technologies were also described. Moreover, a survey is reported of methods to deposit thin films of catalysts on…
Chromium oxide nanoparticles with controlled size prepared from hydrothermal chromium oxyhydroxide precursors
2017
Abstract This work reports the preparation of morphologically well-defined chromium oxide nanoparticles with controlled sizes of 20–30 nm. The synthetic procedure encompass two stages, the first one refers to the preparation of chromium oxyhydroxide nanoparticles by a hydrothermal approach of previously precipitated xerogels, followed by a thermal transformation of CrOOH nanoparticles to Cr2O3. The series of chromium oxyhydroxide particles sized over the range 15–50 nm were prepared through the control of the pH of precipitation of the xerogels and the water/xerogel ratio of the hydrothermal aging. Results showed the formation of non-aggregated oxyhydroxide nanoparticles with two different …
Smart optically active VO2 nanostructured layers applied in roof-type ceramic tiles for energy efficiency
2016
Abstract The capability to control in an smart way the infrared reflectance to environmental temperature variations can be achieved with thermochromic materials like VO2. In this paper, we report the application of VO2 on ceramic tiles aiming to control the reflected infrared radiation on smart roofs and thus improving the energy efficiency, which is associated to the reduction of the carbon dioxide emissions. The VO2 nanoparticles have been produced by hydrothermal synthesis assisted by microwave irradiation, providing a new, quicker and cleaner production route. Afterwards, the VO2 nanoparticles were transferred to the surface of ceramic glassy tiles, which were prepared through dispersin…