Search results for "Shear"

Postactivation potentiation can counteract declines in force and power that occur after stretching.

2016

Stretching can decrease a muscle's maximal force, whereas short but intense muscle contractions can increase it. We hypothesized that when combined, postactivation potentiation induced by reactive jumps would counteract stretch-induced decrements in drop jump (DJ) performance. Moreover, we measured changes in muscle twitch forces and ankle joint stiffness (KAnkle ) to examine underlying mechanisms. Twenty subjects completed three DJs and 10 electrically evoked muscle twitches of the triceps surae subsequent to four different conditioning activities and control. The conditioning activities were 10 hops, 20s of static stretching of the triceps surae muscle, 20s of stretching followed by 10 ho…

Effect of self-etching primer/adhesive and conventional bonding on the shear bond strength in metallic and ceramic brackets

2011

Introduction: Bracket debonding from the tooth surface is a common problem in fixed orthodontics. The aims of the present study were to assess the bond strength and failure sites in two ways of bonding technique, with metallic and ceramic brackets. Material and Methods: One hundred premolars were assigned to 4 groups of 25 each: Group A, metallic brackets/ conventional procedure; Group B, metallic brackets/Transbond XT; Group C, ceramic brackets/conventional procedure; and Group D, ceramic brackets/Transbond XT. Transbond XT composite paste was used for bracket bonding and cured by conventional light-cure device. Specimens were subjected to thermocycling. One week after bonding shearing for…

Impact of Thoracic Endografting on the Hemodynamics of the Native Aorta: Pre- and Postoperative Assessments of Wall Shear Stress and Vorticity Using …

2021

Purpose To quantify the hemodynamic consequences of thoracic endovascular aortic repair (TEVAR) by comparing the preoperative and postoperative wall shear stress (WSS) and vorticity profiles on computational fluid dynamics (CFD) simulations. Materials and Methods The pre- and postoperative computed tomography (CT) scans from 20 consecutive patients (median age 69 years, range 20–87) treated for different thoracic aortic pathologies (11 aneurysms, 5 false aneurysms, 3 penetrating ulcers, and 1 traumatic aortic rupture) were segmented to construct patient-specific CFD models using a meshless code. The simulations were run over the cardiac cycle, and the WSS and vorticity values measured at th…

Haemostatic agents on the shear bond strength of self-adhesive resin

2015

Background Dentin surface contaminated with haemostatic agents can interfere with the bonding of self-adhesive resin cement. Therefore the purpose of this study was to evaluate the effect of various haemostatic agents such as Aluminium chloride, Ferric sulphate and Tannic acid on the shear bond strength of self-adhesive resin luting agent. Material and Methods The buccal surfaces of extracted premolars were flattened to expose the dentine. The teeth were then randomly divided into four groups. In Group I Aluminium Chloride was applied on the flattened dentinal surface, in Group II Ferric Sulphate was applied to exposed dentin surface, in Group III tannic acid was applied on to the dentinal …

Shear coefficient determination in linear friction welding of aluminum alloys

2015

In the present study, a combined experimental and numerical investigation on Linear Friction Welding (LFW) of AA2011-T3 aluminum alloy was carried out in order to find the temperature dependent shear coefficient to be used in a 3D numerical model of the process. Torque, oscillation frequency and pressure were acquired in order to calculate the shear stress at the interface. A numerical thermal model was used to calculate the temperature at the interface between the specimens starting from experimental temperatures acquired through a thermocouple embedded in the LFW specimens. Finally, the calculated shear coefficient was used to model the contact between the two specimens in a dedicated 3D,…

Stirring effects in amyloid fibril formation

2014

Shear models of Rc-encased steel joist beams in MRFs

2019

This study presents the application of different analytical and finite element (FE) models aimed at predicting the shear resistance of reinforced concrete (RC) and reinforced concrete-encased steel joist (HRCESJ) beams with inclined transversal reinforcement in moment resisting frames (MRFs). In particular, four analytical models are taken into account, two of them specifically conceived for HRCESJ beams in seismic area. The analytical models considered are Eurocode-2 model for the shear strength of RC beams; a variable-inclination stress-field approach; a strut-and-tie additive model and, finally, an analytical formulation in which the shear capacity depends on the number of pairs of incli…

Comparison of hemodynamic and structural indices of ascending thoracic aortic aneurysm as predicted by 2-way FSI, CFD rigid wall simulation and patie…

2018

Patient-specific computational modeling is increasingly being used to predict structural and hemodynamic parameters, especially when current clinical tools are not accessible. Indeed, pathophysiology of ascending thoracic aortic aneurysm (ATAA) has been simulated to quantify the risk of complications by novel prognostic parameters and thus to improve the clinical decision-making process related to the intervention of ATAAs. In this study, the relevance of aneurysmal wall elasticity in determining parameters of clinical importance, such as the wall shear stress (WSS), is discussed together with the significance of applying realistic boundary conditions to consider the aortic stretch and twis…

In Silico Shear and Intramural Stresses are Linked to Aortic Valve Morphology in Dilated Ascending Aorta

2017

Objective/Background: The development of ascending aortic dilatation in patients with bicuspid aortic valve (BAV) is highly variable, and this makes surgical decision strategies particularly challenging. The purpose of this study was to identify new predictors, other than the well established aortic size, that may help to stratify the risk of aortic dilatation in BAV patients.Methods: Using fluid-structure interaction analysis, both haemodynamic and structural parameters exerted on the ascending aortic wall of patients with either BAV ( n = 21) or tricuspid aortic valve (TAV; n = 13) with comparable age and aortic diameter (42.7 +/- 5.3 mm for BAV and 45.4 +/- 10.0 mm for TAV) were compared…

On the severity of aortic stenosis in ascending aortic aneurysm: A computational tool to examine ventricular-arterial interaction and aortic wall str…

2020

Abstract An ascending thoracic aortic aneurysm (ATAA) is a life-threatening cardiovascular consequence of vessel dilatation that portends adverse events and death. From a clinical perspective, ATAA should not be treated as an isolated disease, and surgery is often carried out in the presence of AS, aortic insufficiency or a calcified valve leaflet. Aortic stenosis (AS) is common in ATAAs and leads to both vessel rigidity and left ventricular (LV) impairment. In this study, lumped-parameter modeling and computational analysis were used to assess the change in the wall shear stress (WSS) and intramural wall stress of patient-specific ATAA models with different degrees of AS (i.e., mild to sev…