Search results for "Simulation."
showing 10 items of 4779 documents
On the effectiveness of numerical simulation in the prediction of profile distortion in extrusion
2005
Among the so-called ‘traditional processes’, extrusion represents one of the most diffused and utilized, since it permits the production of many industrial parts and raw materials. Of course, relevant knowledge on process mechanics and practice is nowadays available in the technical literature and in properly constructed handbooks. On the other hand, the introduction of finite element simulation, as a powerful analysis and design tool, opened new perspectives. Nowadays many researchers are involved in research tasks aimed at explaining some peculiar extrusion aspects. In this paper the effectiveness of numerical simulation for a complex three-dimensional extrusion process analysis is inves…
Numerical Modelling of Room Thermal Comfort Conditions
2006
Particular heat transfer coefficients of building elements gives quantitative notion only about heat losses through this building element. Analysis of the overall heat balance and heat losses of complete building and study of particular contribution of building elements in overall balance allows one to figure out the state of the building and find the building elements of bounding construction with most significant heat losses. Project variants of the buildings (or rebuilding in case of renovation), which ensure the desirable economy of energy and proportions of investments can be find varying the proportions of the surface area of building elements (e.g., windows and doors). A lot of facto…
A Laboratory Scale Equipment to Relieve Force and Pressure in Cold Extrusion of Lead Hollow Components
2008
Nowadays, many researchers are involved in studies aimed to the explanation of some peculiar aspects regarding manufacturing processes. In this paper, an experimental campaign was carried out in order to reproduce tube extrusion starting from a cylindrical billet. In particular, the development of a proper equipment is presented: the aim was to measure both the total load, by using the testing machine load cell, and the local pressure value on the porthole. The latter task was carried out performing a proper system based on the use of a small load-cell. The tube was extruded with a good surface quality and the external area does not show any welding line evidence. Pure Lead was used for the…
A simulation model for electromagnetic transients in lightning protection systems
2002
This paper deals with the evaluation of electromagnetic transients in a lightning protection system (LPS). A field approach is used, based on the numerical solution of a modified version of the thin-wire electric field integral equation in the frequency domain. Time profiles of interesting electromagnetic quantities are computed by using a discrete fast Fourier transform algorithm. The model takes into account coupling effects among aerial parts and ground electrodes in order to correctly estimate the quantities which can determine electromagnetic hazard inside the LPS; transient touch and step voltages can be easily evaluated also taking into account the human body presence on the soil sur…
Dynamic shakedown of structures under repeated seismic loads
1995
Elastic, perfectly plastic structures are considered under the action of repeated short-duration exitations of seismic type acting in an unknown time sequence, but belonging to a given polyhedral excitation domain. The basic excitations (vertices of the polyhedron) are chosen as discrete-spectrum waves each with frequencies coincident with the first natural frequencies of the structure, and amplitudes related to the ground features and earthquake intensity (according to the Kanai and Tajimi filter model) in such a way that every admissible excitation-obtained as a linear convex combination of the basic ones-has a maximum power not exceeding a given value. In the framework of unrestricted dy…
3D finite element analysis of tool wear in machining
2008
Abstract The paper is focused on the 3D numerical prediction of tool wear in metal cutting operations. In particular, an analytical model, able to take into account the diffusive wear mechanism, was implemented through a specific subroutine. Furthermore, an advanced approach to model heat transfer phenomena at the tool–chip interface was included in the numerical simulation. The adopted simulation strategy gave the possibility to properly evaluate the tool wear. The 3D FEM results were compared with some experimental data obtained turning AISI 1045 steel using uncoated WC tool; a good agreement was found out.
Central Bursting Defects in Drawing and Extrusion: Numerical and Ultrasonic Evaluation
1993
Abstract A new approach for the prediction of central bursting defects in extrusion and drawing is proposed: a finite element analysis of the processes has been carried out, and the obtained results have been elaborated by means of a post-processor, which, employing a proper ductile fracture criterion, is able to suggest if and where the central burst occur. An ultrasonic control system able to detect the insurgence of defects with a resolution of 0.2 mm. has been setup in order to verify the predictive capability of the model. The experimental results show a good agreement with the numerical predictions confirming the effectiveness of the proposed approach, whose industrial application app…
Measuring of Geometrical Precision of Some parts Obtained by Asymmetric Incremental Forming Process After Trimming
2007
Asymmetric Incremental Forming exalts the advantages of Incremental Forming process since no dies are strictly necessary. In this way complex geometries may be manufactured with a very simple clamping equipment. On the other hand, this characteristic determines some intrinsic drawbacks which penalise its industrial suitability; first of all, the dimensional control of the manufactured part is a still open point for researchers all over the world. Several approaches have been already proposed in the last years to solve the problem, resulting only in partial solutions. At the same time, up to now, the numerical simulation did not supply significant aid to the designers, due to the problem com…
DEPENDENCE OF MACHINING SIMULATION EFFECTIVENESS ON MATERIAL AND FRICTION MODELLING
2008
Numerical simulation of cutting processes is still a very difficult matter, although some relevant geometrical simplifications and high-performance codes are used. A large number of technical papers have been focused on the predictive capability of the codes: nevertheless the prediction quality is not very satisfactory if the problem is analyzed in a wide sense. In this paper the simple orthogonal cutting process of a plain-carbon steel is investigated taking into account different process conditions (cutting speed and feed rate). Furthermore, four material constitutive equations and three friction models were implemented and a sensitivity analysis was carried out comparing the numerical pr…
Full-wave analysis of industrial microwave applicators: TM modes
2004
In this paper, full-wave analysis of the TE modes of an industrial cylindrical microwave applicator is presented. The dispersion characteristics and fields configurations are shown. These results are obtained by a numerical simulation based on the residue theory. The authors have obtained particular modes called loop modes, which have a complex propagation constant that describes a loop within the complex plane. © 2004 Wiley Periodicals, Inc. Microwave Opt Technol Lett 42: 46–50, 2004; Published online in Wiley InterScience (www.interscience.wiley.com). DOI 10.1002/mop.20203