Search results for "Simulation."
showing 10 items of 4779 documents
Numerical and experimental verification of new method for connecting pipe to flange by cold forming
2015
Abstract In this paper a new method of connecting pipe to flange without welding is presented. This method is a cold forming process that is based on plastic expansion/deformation of the pipe into a modified standard flange by use of a cold forming tool. The method is patented by Quickflange Technology AS and represents a highly feasible alternative to welding. The successful use of the method requires the ability to predict dimensional and stress/strain characteristics of the pipe and flange after the connection process in order to evaluate the connectivity to the adjacent flange as well as the leak tightness. In addition the ability to predict the process force during the connection proce…
The evaluation of springback in 3D stamping and coining processes
1998
Abstract An effective predictive technique of the elastic springback in a fully 3D 90° V-punch V-die bending process is presented. This is based on a combined approach in which an explicit finite element code was used to simulate the loading phase of the process whilst an implicit procedure was used to analyse the springback phase. Two different punches with a nose radius of 4 and 8 mm were used. An increase in the springback ratio with the coining load was observed with the lower nose radius. Conversely, an increase in the springback ratio with the coining load up to a peak value (>1), corresponding to a force of about 20 kN, followed by a decrease in the springback ratio with increasing t…
Concurrent optimization of size and switch-on priority of a multisource energy system for a commercial building application
2015
Abstract In recent years, the governments of most nations have pledged to (i) limit carbon dioxide emissions, (ii) reduce primary energy consumption by increasing production, distribution and end-use efficiency and (iii) increase the utilization of renewable energy sources. In general, these goals are pursued separately by law, by subsidizing renewable energy technologies, reducing the demand or using high efficiency technologies. In this context, multi-source systems for the fulfillment of energy demands are highly advantageous because they are based on different technologies which use renewable, partially renewable and fossil energy sources. However, the main issues of multi-source system…
Simulation model of a molten carbonate fuel cellemicroturbine hybrid system
2011
A Hybrid System based on High Temperature Fuel Cells coupled to a Microturbine allows a high efficiency, low environmental pollution and it may be exploited as a CHP System producing heat and electricity both Grid Connected and Stand Alone; the overall electrical efficiency could reach a very high value (up to 60%) and total efficiency could be over 70% including the contribution due to heat recovery. In the context of wide research activities of ENEA on High Temperature Fuel Cells and Hybrid Systems e that involve materials, system BoP and fuels e a very great effort has been devoted to design and build, in the ENEA Research Centre of “Casaccia”, an experimental Test-Rig based on a Molten …
TRACE and RELAP5 Codes for Beyond Design Accident Condition Simulation in the SPES3 Facility
2012
Code validation on qualified experimental data is a fundamental issue in the design and safety analyses of nuclear power plants. The SPES3 facility is being built at the SIET laboratories for an integral type SMR simulation, in the frame of an R&D program on nuclear fission, funded by the Italian Ministry of Economic Development and led by ENEA. The facility, based on the IRIS reactor design, reproduces the primary, secondary and containment systems with 1:100 volume scale, full elevation and prototypical fluid and thermal-hydraulic conditions. It is suitable to test the plant response to design and beyond design accidents in order to verify the effectiveness of the primary and containm…
Analyses of the OSU-MASLWR Experimental Test Facility
2012
Today, considering the sustainability of the nuclear technology in the energy mix policy of developing and developed countries, the international community starts the development of new advanced reactor designs. In this framework, Oregon State University (OSU) has constructed, a system level test facility to examine natural circulation phenomena of importance to multi-application small light water reactor (MASLWR) design, a small modular pressurized water reactor (PWR), relying on natural circulation during both steady-state and transient operation. The target of this paper is to give a review of the main characteristics of the experimental facility, to analyse the main phenomena characteri…
Simultaneous zonation and calibration of pipe network parameters
2003
A procedure for simultaneously zoning and calibrating pipe network parameters is proposed and applied to the determination of pipe resistance coefficients. The methodology is aimed at grouping the parameters of all the pipes into a small number of zone parameters, constrained to keep the difference between the computed and the measured water heads below a given tolerance. It is shown that, in the case of nonlooped networks, the methodology leads to a linear minimization problem where the objective function is a measure of the heterogeneity of the estimated parameters. In the case of looped networks an iterative procedure, where the linear problem is coupled with a nonlinear problem having a…
A DC-DC power converter for PV module characterization
2014
In this paper, a standard-compliant electronic load setup for PV module curve detection which features high accuracy, low cost and components count is proposed. The proposed device is based on a DC-DC power converter in open-loop configuration. The proposed system is designed according to regulation constraints in order to achieve high performances in curve detection. Design criteria are discussed. The model is implemented in PSIM environment. Simulation based on data input of a commercial PV Conergy E215P module are carried out under several environmental conditions to show the accuracy of the proposed electronic load. Simulation results are reported.
Dynamics photovoltaic generators: Technical aspects and economical valuation
2010
The strategy adopted from many European nations and not, to entrust the electric energy production to differently energetic sources has determined an increment of the scientific research for the solar resource exploitation. These scientific community activities follows with attention from the entrepreneurial world have concentrated on the innovative techniques and methodologies of the source conversion, solar concentration and the direction's device optimization. This job focuses its attention on the simple application of solar-track device, based on consolidated technologies. The diffused application of these dispositive, could be, shortly, an important increment of electricity generation …
A statistic approach of cables ageing in MV lines on thermal and electrical combined stress
2006
The paper introduces a methodology that through a probabilistic characterisation of load for MV network, and implementing a life model for combined electric and thermal stresses, simulates the process of ageing of the insulating materials evaluating the expected life time of the cable. Such evaluation is necessary to the possibility of assuming less restrictive thermal overloading limits on electrical cables, with the consequential increase on reserve that cables could offer. A numerical example is reported to better explain the methodology