Search results for "Simulation"
showing 10 items of 5095 documents
New Procedures of Pattern Classification for Vibration-Based Diagnostics via Neural Network
2014
In this paper, the new distance-based embedding procedures of pattern classification for vibration-based diagnostics of gas turbine engines via neural network are proposed. Diagnostics of gas turbine engines is important because of the high cost of engine failure and the possible loss of human life. Engine monitoring is performed using either ‘on-line’ systems, mounted within the aircraft, that perform analysis of engine data during flight, or ‘off-line’ ground-based systems, to which engine data is downloaded from the aircraft at the end of a flight. Typically, the health of a rotating system such as a gas turbine is manifested by its vibration level. Efficiency of gas turbine monitoring s…
Modular, customisable, accomodation-friendly antenna system for satellite avionics: Development, prototyping and validation
2014
In the frame of ESA program AO/1- 6737/11/NL/MH, an innovative X-band antenna system for satellite avionics has been studied, demonstrated and validated at Proof of Concept Model level. The innovative contribution of such an antenna system relies on modularity, customizability and accommodation friendliness. The antenna concept is based on a Plug and Play architecture, where the basic module is a 2.7 cm-cube with a mass of 53 gr, which can be clustered in array configuration. A catalogue of predefined and ready-to-use clusters could be developed with the possibility of adapting the antenna systems to various platform types by tuning just a few control parameters. Different levels of customi…
Integrating Advanced Visual Information with Ball Projection Technology Constrains Dynamic Interceptive Actions
2014
The role of advanced visual information in ball catching was investigated by integrating video images of action and ball projection technology in four different conditions: Integrated video and ball projection (VBP), Video-Only (VO), Ball Projection-Only (BPO) and Misleading Ball projection (MBP). Hand kinematics and gaze behaviour data were collected from participants who attempted to catch balls one handed in all conditions. During VBP, catching performance was more successful, tracking of the ball occurred earlier and lasted longer, with maximum grip aperture emerging earlier with a slower maximum velocity than in BPO. During VO, movement emerged later than VBP, with larger maximum and m…
Investigation of thick sheet AHSS springback in combined bending under tension
2012
In this paper, we investigate the springback behavior of several advanced high-strength sheet steels (TRIP, Dual-Phase, ferrite-bainite) with thicknesses up to 4 mm. Samples were tested by means of the bending-under-tension (BUT) test. The BUT has been extensively applied, in the literature, to relatively thin (1 mm and thinner) sheet metals for automotive applications; the applicability of several guidelines from the literature was investigated in this work in the context of thick advanced high strength steel (AHSS) sheets and using a sample width of 12 mm. The monotonic decrease of springback as back force increased was confirmed for this category of sheet steels, and a general trend for …
A full body musculoskeletal model based on flexible multibody simulation approach utilised in bone strain analysis during human locomotion
2011
Load-induced strains applied to bone can stimulate its development and adaptation. In order to quantify the incident strains within the skeleton, in vivo implementation of strain gauges on the surfaces of bone is typically used. However, in vivo strain measurements require invasive methodology that is challenging and limited to certain regions of superficial bones only such as the anterior surface of the tibia. Based on our previous study [Al Nazer et al. (2008) J Biomech. 41:1036-1043], an alternative numerical approach to analyse in vivo strains based on the flexible multibody simulation approach was proposed. The purpose of this study was to extend the idea of using the flexible multibod…
Take-off aerodynamics in ski jumping
2001
The effect of aerodynamic forces on the force-time characteristics of the simulated ski jumping take-off was examined in a wind tunnel. Vertical and horizontal ground reaction forces were recorded with a force plate installed under the wind tunnel floor. The jumpers performed take-offs in non-wind conditions and in various wind conditions (21-33 m s(-1)). EMGs of the important take-off muscles were recorded from one jumper. The dramatic decrease in take-off time found in all jumpers can be considered as the result of the influence of aerodynamic lift. The loss in impulse due to the shorter force production time with the same take-off force is compensated with the increase in lift force, res…
An integrated model for biological and physical process simulation in membrane bioreactors (MBR).
2011
Abstract Mathematical modelling of membrane bioreactors (MBRs) for wastewater treatment has targeted either the biological processes (treatment quality target) as well as various aspects of system management. However, the high number of interactions among the involved physical–chemical processes, hampers a straightforward mathematical modelling. This circumstance is much more emphasized for submerged MBR systems where the membrane is immersed in an aeration tank. One of the main crucial points that prevents a comprehensive understanding is the interpretation of the fouling phenomenon and its connections with the biological processes. An overall mathematical model for MBR has not been comple…
Visual-based Feedback Control of Casting Manipulation
2006
In this paper, we present a method to control casting manipulation by means of real-time visual feedback. Casting manipulation is a technique to deploy a robotic end-effector at large distances from the robot’s base, by throwing the end-effector and controlling its ballistic flight using forces transmitted through a light tether connected to the end-effector itself. The tether cable can also be used to retrieve the end-effector and exert forces on the robot’s environment. Previous work has shown that casting manipulation is able to catch objects at a large distance, proving it viable for applications such as sample acquisition and return, rescue, etc. In previous experiments, the position o…
Adaptive neural-fuzzy inference system based method to modeling of vehicle crash
2013
Various areas of research need to be considered in order to establish a mathematical model of a vehicle crash. To enhance the modeling process, a novel ANFIS-based approach to reconstruct behavior of impacting vehicles is presented in this paper. Kinematics of center of gravity (COG) a vehicle involved in an oblique barrier collision is reproduced by application of a five-layered ANFIS structure. Then, the same ANFIS system is used to simulate a different collision type than the one which was used in the training stage. The points of interests are selected to be the locations of accelerometers mounting. The accuracy of the proposed method is evaluated by the comparative analysis with the re…
DSC: software tool for simulation-based design of control strategies applied to wastewater treatment plants.
2011
This paper presents a computer tool called DSC (Simulation based Controllers Design) that enables an easy design of control systems and strategies applied to wastewater treatment plants. Although the control systems are developed and evaluated by simulation, this tool aims to facilitate the direct implementation of the designed control system to the PC of the full-scale WWTP (wastewater treatment plants). The designed control system can be programmed in a dedicated control application and can be connected to either the simulation software or the SCADA of the plant. To this end, the developed DSC incorporates an OPC server (OLE for process control) which facilitates an open-standard communic…