Search results for "Sintering"

Dense nanostructured materials obtained by spark plasma sintering and field activated pressure assisted synthesis starting from mechanically activate…

2004

The preparation of highly dense bulk materials with a grain size in the range of a few to a few hundreds nanometers is currently the objective of numerous studies. In our research we have achieved a measure of success in this regard by using the methods of mechanically-activated, field-activated, pressure-assisted synthesis, MAFAPAS, which has been patented, and mechanically-activated spark plasma sintering, MASPS. Both methods, which consist of the combination of a mechanical activation step followed by a consolidation step under the simultaneous influence of an electric field and mechanical pressure, have led to the formation of dense nanostructured ceramics, intermetallics, and composite…

Advanced Usage of SPS Technology for Producing Innovative Materials

2014

Ceramic/metal nanocomposites by lyophilization: Spark plasma sintering and hardness

2014

The present study is focused on the procedure of spray-drying and lyophilization techniques for the preparation of ceramic/metal nanocomposites. The results of the study at all stages are compared with those corresponding to powders conventionally dried by heating in furnace. Starting from aqueous solutions of metal salts and ceramic powders, the procedure follows with spray-drying, lyophilization, calcination of the resulting powders and subsequent Spark Plasma Sintering (SPS). X-ray diffraction analysis of the powders at different stages of the processing routes was used for phase indexing; further characterization was performed by Transmission Electron Microscopy and Energy Dispersive X-…

Mechanical, degradation and drug-release behavior of nano-grained Fe-Ag composites for biomedical applications.

2018

Abstract An original fabrication route of high-strength bulk Fe-5Ag and Fe-10Ag nanocomposites with enhanced degradation rate is reported. Near fully dense materials with fine nanostructures and uniform distribution of Ag nanoparticles were obtained employing high energy attrition milling of Fe-Ag2O powder blends followed by cold sintering – high pressure consolidation at ambient temperature that allowed the retention of the nanoscale structure. Annealing in hydrogen flow at 550 °C resulted in enhanced ductility without coarsening the nanostructure. The strength in compression of Fe5Ag and Fe10Ag nanocomposites was several-fold higher than the values reported for similar composites with mic…

Bulk Nanostructured Materials Obtained by Powder Sintering

2007

Influence of Compressive Stress on Dielectric and Ferroelectric Properties of the(Na0.5Bi0.5)0.7Sr0.3TiO3Ceramics

2013

Good quality lead-free ceramics of (Na0.5Bi0.5)0.7Sr0.3TiO3(NBTS30) have been produced by a solid phase sintering process. The dependence of dielectric and ferroelectric properties on the unaxial pressure (0–1200 bar) were investigated. A shift and decrease of maximum value of e, decrease of the thermal hysteresis and coercive field and increase of polarization with increasing pressure were observed. The results were discussed in terms of an elastic changes in inter-ionic distances in a crystal structure and switching nanoregions under the action of pressure. The NBTS30 ceramic is expected to be a new promising candidate for lead-free electronic material.

Thermoelectric properties of spark-plasma sintered nanoparticular FeSb2prepared via a solution chemistry approach

2013

Nanoparticular FeSb2 was prepared in solution from cyclopentadienyl iron(ii) dicarbonyl dimer [Fe(Cp(CO)2)]2 and antimony nanoparticles. Spark plasma sintering was used as consolidation method to maintain the particle size. The thermoelectric performance of FeSb2 is limited by its high thermal conductivity. In this work, the thermal conductivity was suppressed by nearly 80% compared to the bulk value by introducing grain boundary scattering of phonons on the nanoscale. The thermoelectric properties of the consolidated FeSb2 emphasize the possibility of altering thermal transport of promising thermoelectric compounds by phonon scattering by engineering the interfaces at the nanoscale.

Time-resolved cathodoluminescence and photoluminescence of nanoscale oxides

2009

The nanostructured oxide materials such as ZnO, ZrO2, and Y3Al5O12 (YAG) are perspective materials for transparent scintillating and/or laser ceramics. The luminescence properties of single crystals, nanopowders and ceramic were compared. Nominally pure and rare-earth doped nanopowders and ceramics have been studied by means of time-resolved luminescence spectroscopy. The fast blue luminescence band was studied in ZnO ceramics sintering from different raw materials. The luminescence centres of ZrO2:Y were compared in a single crystal, ceramic and nanopowder. It is shown that ceramic sintering parameters have a strong influence on time-resolved luminescence characteristics in cerium-doped YA…

Powder metallurgy processing and deformation characteristics of bulk multimodal nickel

2014

cited By 7; International audience; Spark plasma sintering was used to process bulk nickel samples from a blend of three powder types. The resulting multimodal microstructure was made of coarse (average size ∼ 135 μm) spherical microcrystalline entities (the core) surrounded by a fine-grained matrix (average grain size ∼ 1.5 μm) or a thick rim (the shell) distinguishable from the matrix. Tensile tests revealed yield strength of ∼ 470 MPa that was accompanied by limited ductility (∼ 2.8% plastic strain). Microstructure observation after testing showed debonding at interfaces between the matrix and the coarse entities, but in many instances, shallow dimples within the rim were observed indica…

Sintering of Fe2NiO4 with an internal binder: a way to obtain a very dense material

2003

Abstract The coupled synthesis and sintering of Fe2NiO4 can be carried out from the calcination under air at high temperatures (>1200 °C) of precompacted (under 12 MPa) pellets of different mixtures: NiO/α-Fe2O3; NiO/α-Fe2O3/Fe; NiO/α-Fe2O3/Ni. The densest material is obtained at 1200 °C only from the following mixture: NiO (40 mol%), α-Fe2O3 (50 mol%) and Ni (10 mol%). Because the metallic nickel is very ductile, it is used as an internal binder in order to enhance the precompacting of the samples. Moreover, the role of nickel is to enhance the sintering reaction. This route leads to a final material of relative density close to 98±2%.