Search results for "Spall"

Depassivation Experiments by Laser‐Pulse‐Induced Spallation

1992

Depassivation experiments have been conducted by applying a technique developed for adhesion tests. A laser-pulse-induced spallation of the passive film is induced in situ without any contact between the laser beam and the passive film. The depassivation is controlled by the short pressures induced at the metal-film interface. The interfacial stresses at the metal-film interface could be studied by this technique

Rare earths, zirconium and hafnium distribution in coastal areas: The example of Sabella spallanzanii (Gmelin, 1791)

2016

The Zr, Hf, Y and lanthanide (REE) distribution in biological tissues of Sabella spallanzanii and Styela plicata species collected from two harbours from the northern Sicily is studied for providing information regarding the Zr, Hf and REE uptake from the environment. Previous studies determined the fractionation of dissolved REE scavenged on binding sites onto biological surfaces. By comparing the recognised shale-normalised REE patterns of studied samples with evidence from reference data, the observed behaviour of these elements in biological tissues of Sabella spallanzanii and Styela plicata is interpreted to result from the preferential uptake of intermediate REE onto carboxylic sites.…

Purificazione di una lectina calcio dipendente dal muco di Sabella spallanzanii (Polychaeta: Sabellidae)

2010

A comparison between the chemical behaviour of lead-gold and lead-bismuth eutectics towards 316L stainless steel

2013

Radiochimica acta, 101 (10)

A simple model for the calculation of the axial load-carrying capacity of corroded RC columns

2015

In the present paper, a simplified model is used to determine the axial load-carrying capacity of compressed short reinforced concrete columns subjected to corrosion processes. The model considers members with circular and square cross-sections and accounts for—cover spalling, —concrete core confinement induced by transverse steel reinforcement, —buckling of longitudinal reinforcing bars. Strength reduction in concrete cover and core due to cracking induced by rust formation, reduction of steel area in longitudinal bars and transverse stirrups due to general and pitting corrosion and loss of confinement pressure are considered. The load-carrying capacity and load-axial strain curves here ge…

Moment-axial force domain of corroded R.C. columns

2016

In the present paper, a simple model to determine the moment-axial force domain of the cross-section of reinforced concrete (R.C.) columns subjected to corrosion process is presented. The model considers members with square and rectangular cross-sections and it accounts for—cover spalling; buckling of longitudinal reinforcing bars; loss of bond of bar in tension; reduction of confinement pressures (due to the reduction of the area of stirrups and cracking of concrete induced by rust formation). The analytical expressions for prediction of the area reduction of steel, bond strength and critical load of longitudinal bars utilized were verified against experimental data available in the litera…

Behavior of fiber-reinforced concrete columns under axially and eccentrically compressive loads

2010

An experimental investigation into the behavior of 16 short, confined, reinforced concrete columns with and without steel fibers was carried out. The columns with square sections had a concrete core 165 x 165 mm (6.49 x 6.49 in.) at the midsection and were hunched at the ends to apply eccentric loading and prevent boundary effects. The specimens were tested to failure at different strain rates under two loading schemes: concentric compression and eccentric compression with a constant eccentricity. The axial load and axial strains were obtained to evaluate the effects of the presence of steel fibers, the thickness of the cover concrete, and the eccentricity of the applied axial load. The com…

The effect of rare earths deposited on steel surfaces, by different processes (sol/gel, electrophoresis, OMCVD), on high temperature corrosion behavi…

1993

Abstract In this paper, different methods of rare earth oxides deposition on the surface of AISI 304 steel are described: sol/gel, electrophoresis in aqueous or organic medium, OMCVD of rare earth β-diketonates. After the deposition, all the samples were reheated. This treatment was absolutely essential for a strengthening effect of the protective oxide scale. Oxidation of coated and non-coated samples was performed under isothermal and cyclic conditions. The effect of rare earth deposition is significant in isothermal conditions. However, in thermal cyclic conditions, the effect of a rare earth deposited on surface is spectacular. Scale spallation is then completely avoided under the chose…

Simulation of H- ion source extraction systems for the Spallation Neutron Source with Ion Beam Simulator.

2012

A three-dimensional ion optical code IBSimu, which is being developed at the University of Jyväskylä, features positive and negative ion plasma extraction models and self-consistent space charge calculation. The code has been utilized for modeling the existing extraction system of the H(-) ion source of the Spallation Neutron Source. Simulation results are in good agreement with experimental data. A high-current extraction system with downstream electron dumping at intermediate energy has been designed. According to the simulations it provides lower emittance compared to the baseline system at H(-) currents exceeding 40 mA. A magnetic low energy beam transport section consisting of two sole…

Influence of the mode of introduction of a reactive element on the high temperature oxidation behavior of an alumina-forming alloy. Part I: Isotherma…

2004

Several routes of yttrium introduction were applied to test the high temperature oxidation performance of a FeCrAl alloy. Isothermal oxidation tests were described in a previous paper (Part I of this paper in this journal, 2004, 55, 352). Cyclic oxidation tests were performed in air under atmospheric pressure on blank specimens, Y 2 O 3 sol-gel coated-, Y 2 O 3 metal-organic chemical vapor deposited (MOCVD)-, yttrium ion implanted-alloys, as well as on a steel containing 0.1 wt.% of yttrium as an alloying element. For the 20 hours cycles, all the samples, except FeCrAl-0.1Y, exhibit weight losses after a few cycles, indicating drastic spallation of the oxide scales. The MOCVD coated specime…