Search results for "Stress analysis"
showing 10 items of 58 documents
Deformation analysis of ATHENA test filters made of plastic thin films supported by a mesh under differential static pressure
2019
Within ESA Cosmic Vision 2015-2025 Science Program, ATHENA was selected to be a Large-class high energy astrophysics space mission. The observatory will be equipped with two interchangeable focal plane detectors named X-Ray Integral Field Unit (X-IFU) and Wide Field Imager (WFI). In order to optimally exploit the detector sensitivity, X-ray transparent filters are required. Such filters need to be extremely thin to maximize the X-ray transparency, that is, no more than a few tens of nm, still they must be able to sustain the severe stresses experienced during launch. Partially representative test filters were made with a thin polypropylene film, coated with Ti, and supported by a thin highl…
Fracture Toughness of Hydrothermally Aged Epoxy Systems with Different Crosslink Density
2015
Abstract The present work investigates the fracture toughness behaviour of Single Edge Notched Bending (SENB) samples of epoxy systems subject to water uptake aging. Two epoxy systems with a significantly different Glass Transition Temperature, T g , are in particular considered: a typical commercial non-aeronautical grade resin matrix for composite applications, reaching a T g of 90 °C, and a DGEBA+DDS epoxy system achieving a T g of 230 °C.The materials have been conditioned by hydrothermal aging in a thermal bath at the temperature of 50 °C. TransmissionPhotoelastic Stress Analysisis carried outon SENB samples during water aging, monitoring the presence and evolution of swelling stresses…
Evaluation of continuous filament mat influence on the bending behaviour of GFRP pultruded material via Electronic Speckle Pattern Interferometry
2017
Abstract Pultrusion is a process allowing the production of unidirectional (roving) fibre-reinforced polymer (FRP) structural elements with constant cross section. Recently, also civil engineers focused their attention on pultruded composite materials as alternative to traditional ones (e.g., concrete, steel). Furthermore, to improve the transverse strength and stiffness with respect to the fibres direction, continuous filament mat (CFM) is often placed within the stacking sequence. The CFM influence on the global mechanical behaviour is not considered by appropriate actual international standards. In this paper, the influence of the CFM layers on the mechanical behaviour of glass fibres pu…
Investigation of the crack tip stress field in a stainless steel SENT specimen by means of Thermoelastic Stress Analysis
2019
Abstract In this work a Thermoelastic Stress Analysis (TSA) setup is implemented to investigates the Thermoelastic and Second Harmonic signals on a fatigue loaded Single Edge Notched Tension (SENT) specimen made of stainless steel AISI 304L. Three load ratios are in particular applied, R=-1, 0, 0.1. The thermoelastic signal is used to evaluate the Stress Intensity Factor via two approaches, the Stanley-Chan linear interpolation method and the over-deterministic least-square fitting (LSF) method using the Williams’ series expansion. Regarding least-square fitting, an iterative procedure is proposed to identify the optimal crack tip position in the thermoelastic maps. The SIF and T-Stress are…
Determination of Torsional Stresses in Shafts: From Physical Analogies to Mathematical Models
2015
This paper presents the historical development of methods used for the study of torsional stresses in shafts. In particular, the paper covers both analog methods, especially those based on electrical analogies proposed circa 1925, and numerical methods, especially finite difference methods (FDM), finite element methods (FEM) and boundary element methods (BEM).
Molar distalization with pendulum appliances in the mixed dentition: effects on the position of unerupted canines and premolars.
2004
Introduction: The pendulum appliance allows for rapid molar distalization without the need for patient compliance. Its efficiency has been confirmed in a number of clinical studies. However, the potential interactions and positional changes between the deciduous molars used for dental anchorage and the erupted and unerupted permanent teeth have yet to be clarified when this appliance is used for molar distalization in the mixed dentition. Methods: Twenty-nine patients in the mixed dentition each received a modified pendulum appliance with a distal screw and a preactivated pendulum spring for bilateral distalization of the maxillary molars. The patients were divided into 4 groups based on de…
Thermoelastic signal processing using an FFT lock-in based algorithm on extended sampled data
2009
A fast infrared scanner is used to acquire the thermoelastic effect induced temperature changes along a line on the surface of cyclically loaded tensile samples. The raster scanning movement of the single detector allows the sampling of temperature versus time. This data are then post-processed by means of a lock-in algorithm coupled with 1D and 2D FFT analyses in order to filter out the thermoelastic signal from the noisy measured signal. A data extension algorithm is proposed which uses the information from different acquired frames to extend the data sampling window. The whole signal processing setup is evaluated on experimental data with successful results, proposing a potential tool fo…
Experimental evaluation of through-the-thickness stress distribution in transverse crack tension test samples
2015
Transverse Crack Tension (TCT) samples represent an alternative to End Notched Flexure configurations for the characterization of pure mode II fracture toughness of Fibre Reinforced Polymer composites. TCT is supposed to reproduce a pure Mode II failure mechanism while avoiding the frictional energy dissipation between the flanks of a starter crack. The TCT geometry is that of a unidirectional tensile sample where a number of embedded plies, centered on the middle plane, are cut in the transverse fibres direction. The tensile loading should then activate four symmetric fronts of mode II delamination from the transverse cut tips. The present work describes the implementation of two full fiel…
Rilevamento del segnale termoelastico a campo intero mediante analisi lock-in in modalità off-line
2014
Il presente lavoro propone una procedura di post-processamento del segnale termografico misurato su provini sollecitati in modo ciclico al fine di ricavare il segnale termoelastico. Dopo aver descritto la Correlazione Lock-In, usata tradizionalmente dai sistemi commerciali per ricavare il segnale termoelastico, il lavoro mostra come tale procedura sia numericamente equivalente alla determinazione delle armoniche della Trasformata di Fourier Discreta (TFD) del segnale campionato. Viene quindi proposta ed implementata una procedura di filtraggio del segnale termoelastico basata sulla applicazione diretta della TFD, che ha il vantaggio di poter in alcune circostanze fare a meno di un segnale d…
On the history of torsional stress concentrations in shafts: From electrical analogies to numerical methods
2014
This article proposes a retrospective on experimental and numerical methods developed throughout the past century to solve the torsion problem in shafts, with particular emphasis on the determination of shear stress concentration factors in discontinuities of typical use in shaft design. This article, in particular, presents the theory and related solutions distinguishing between two classes of geometries: shafts with constant cross section and axisymmetric shafts with variable diameter. Emphasis is given to approaches based on physical analog methods and, in particular, those based on electrical analogies proposed since about 1925. Experimental methods based on structural physical models …