Search results for "Structural engineering"
showing 10 items of 1998 documents
Conceptual design of prestressed slab bridges through one-way flexural load balancing
2013
In this paper a study on prestressed concrete slab bridges is presented. A design philosophy based on the concept of load balancing through prestressing is proposed in order to minimize the effects of delayed deformations due to creep. Aspects related to the stress redistribution inside these bridges for time-dependent phenomena are analyzed and discussed, by applying the principles of aging linear visco-elasticity. Prestressing is seen as an equivalent external load which counterbalances the permanent loads applied to the bridge, nullifying the elastic deflections due to sustained loads, and thus avoiding the related delayed deformations. An optimization of the structural behavior through …
Serviceability and Ultimate Safety Checks of SegmentalConcrete Bridges through N-M and M-V Interaction Domains
2015
In current engineering practice, safety checks on serviceability and determinations of ultimate limit states of segmental bridges built by cantilevering are generally performed, either considering separately the contributions of axial force N, bending moment M, and shear force V, or considering the interaction effects through approximate expressions supplied by building codes. During construction stages and service life, the interaction between internal forces can be of fundamental importance in establishing the actual degree of structural safety and, for this reason, a different philosophy for performing checks in segmental bridges is proposed in this paper, plotting N-M and M-V interactio…
Simplified model for compressive response of RC column footing with square cross-section
2017
Abstract In this paper, a simplified calculus model for the prediction of the compressive response of RC column footing with a square cross-section is presented. As it is well-known RC concrete footing are designed adopting uniform contact pressures on the substrate and assuming a strut and tie model in deep members and a cantilever beam or slab model in flexible members. Deep and flexible members are distinguished in literature only based on the tangent of the angle expressed as the ratio between the depth and the shear span of the footing. In this paper, several subgrade contact pressures distribution for column footings (rigid or soft soils) were considered in developing a mechanical mod…
Partial Elastic Scheme Method in Cantilever Construction of Concrete Arch Bridges
2013
AbstractIn this paper, a study about stay stressing procedures of concrete arch bridges built by cantilevering with temporary stays is presented. Particularly, the partial elastic scheme method is proposed to find the initial cable forces, and a forward procedure is implemented to follow the actual sequence of construction by extending a procedure already applied to concrete cable–stayed bridges. The theoretical treatment is followed by a numerical application on a case study of a concrete arch bridge, and a comparison between initial cable forces found by the partial elastic scheme method and classical backward analysis is presented here. Results show the effectiveness of the proposed proc…
The influence of time-dependent phenomena in segmental construction of concrete cable-stayed bridges
2011
Construction stages of a cable-stayed bridge are characterized by a sequence in which geometric configuration, restraints and consequently stress and strain patterns vary many times till the final arrangement is achieved. When construction of concrete bridges is made by cantilever method the influence of time-dependent phenomena becomes significant. In this study an evaluation of stay stressing procedures is given by taking into account creep and shrinkage in cantilever construction of concrete cable-stayed bridges. A methodology of stay stressing is proposed with the final target of reaching the desired geometric configuration. Comparison with classical analyses performed by backward metho…
A parametric study of curved incrementally launched bridges
2013
Abstract The structural behaviour of incrementally launched bridges in the construction stages depends on different parameters involving deck, nose, supports and guide devices, because static schemes vary continuously with the advance of the deck above the piers. For this reason temporary stresses in the deck, during launching, are rather different from those occurring in service life. Horizontally curved launched bridges also present the effects of torsion induced by geometric curvature. A parametric study is presented in order to analyse the influence of design parameters on the construction of these bridges. Analyses were carried out by extending to curved beams a procedure based on the …
Analytical prediction of load deflection curves of external steel fibers R/C beam–column joints under monotonic loading
2015
Abstract In this paper a simplified analytical model able to reproduce the flexural behavior of external beam–column joints under monotonic loading is presented, to be used for pushover analysis. The subassemblage (beam, column and joint) is subjected to a constant vertical load acting on the column and to a monotonically increasing lateral force applied at the tip of the beam. The model is specific for hooked steel fiber-reinforced concrete (FRC) and is designed to calculate the flexural response in the form of a load–deflection curve, of beam–column subassemblages. No bond failure and shear deformations are considered in the present paper. The model includes shear-to-moment interaction fo…
A practical approach for the strength evaluation of RC columns reinforced with RC jackets
2015
Abstract Reinforced concrete (RC) jacketing is nowadays one of the most common techniques adopted for seismic retrofitting of existing RC columns. It is used to increase load-carrying capacity and ductility of weak existing members by means of a simple and cheap method. The structural efficiency is related to two main effects: – the enlargement of the transverse cross section; – the confinement action provided by the external jacket to the inner core. Several theoretical and experimental studies were addressed in the past to investigate on how it is possible to calculate the strength enhancement due to these effects and to highlight the main key parameters influencing the structural behavio…
Load carrying capacity of RC compressed columns strengthened with steel angles and strips
2012
Abstract In this paper a comparison between the analytical expressions for the prediction of the load carrying capacity of strengthened reinforced concrete (RC) columns with steel angles and strips is made. Expressions examined consider: the strength contribution due to the confinement effects induced by transverse strips; the composite action due to steel angles and unconfined concrete core; the strength contribution due to the composite actions of angles and concrete core taking into account that steel angles are subjected to axial force and bending moment and concrete core is confined by transverse strips. Design rules given by recent codes for the design of the strengthened columns are …
Numerical Analysis of Piezoelectric Active Repair in the Presence of Frictional Contact Conditions
2013
The increasing development of smart materials, such as piezoelectric and shape memory alloys, has opened new opportunities for improving repair techniques. Particularly, active repairs, based on the converse piezoelectric effect, can increase the life of a structure by reducing the crack opening. A deep characterization of the electromechanical behavior of delaminated composite structures, actively repaired by piezoelectric patches, can be achieved by considering the adhesive layer between the host structure and the repair and by taking into account the frictional contact between the crack surfaces. In this paper, Boundary Element (BE) analyses performed on delaminated composite structures …