Search results for "Surface finish"
showing 7 items of 167 documents
Coupling two radar backscattering models to assess soil roughness and surface water content at farm scale
2013
Remote sensing techniques are useful for agro-hydrological monitoring at the farm scale because the availability of spatially and temporally distributed data improves agricultural models for irrigation and crop yield optimization under water scarcity conditions. This research focuses on the surface water content retrieval using active microwave data. Two semi-empirical models were chosen as these showed the best performances in simulating cross and co-polarized backscatter. Thus, these models were coupled to obtain reliable assessments of both soil water content and soil roughness. The use of the coupled model enables one to avoid using roughness measured in situ. Remote sensing images and …
Optimization of the straightness measurements on rough surfaces by Monte Carlo simulation
2013
Summary The straightness error of a coordinate measuring machine (CMM) is determined by measuring a rule standard. Thanks to a reversal technique, the straightness uncertainty of the CMM is theoretically dissociated from the straightness uncertainty of the rule. However, stochastic variations of the whole measurement system involve uncertainties of the CMM straightness error. To quantify these uncertainties, different sources of stochastic variations are listed with their associated probability density functions. Then Monte Carlo methods are performed first to quantify error and secondly to optimize measurement protocol. It is shown that a 5-measurement distance from 0.1 mm to each measurem…
The Relevance Of The Preform Design In Coining Processes Of Cupronickel Alloy
2007
Coining is a forging process in which a metallic disk, characterized by a low volume‐surface ratio, is deformed with the aim to impress 3D images on its three surfaces. Due to the large production volumes and, at the same time, to the high quality standards required to the final products in terms of final dimensions, tolerances and surface finishing, such closed‐die, cold forging process requires a careful evaluation and choice of the proper operative parameters. In particular, along with technological parameters as the die velocity, die stroke and lubrication, which, in turn, contribute to affect the pressure values on the die surfaces, and thus the press choice, geometrical parameters as …
Comment on “Effects of different tillage practices on the hydraulic resistance of concentrated flow on the loess plateau in China” by J. Sun et al
2020
Abstract For concentrated flows, which are characterized by small water depth and steep sloping beds, hydraulic conditions different from those typical of streams and rivers occur. In this study a new theoretically deduced flow resistance equation was tested using the experimental data by Sun et al. for three different tilled surfaces (Manual Dibbling, MD, Manual Hoeing, MH, and Contour Drilling, CD). At first, the profile parameter-relationship, which is the relationship between the velocity profile parameter Γ, the channel slope and the flow Froude number, was calibrated using rill flow data by Di Stefano et al. Then, the applicability of this relationship was tested by the measurements o…
Surface Morphology of Single and Multi-Layer Silicon Nitride Dielectric Nano-Coatings on Silicon Dioxide and Polycrystalline Silicon
2019
Silicon nitride (Si3N4) in a form of single and multi-layer nanofilms is proposed to be used as a dielectric layer in nanocapacitors for operation in harsh environmental conditions. Characterization of surface morphology, roughness and chemical bonds of the Si3N4 coatings has an important role in production process as the surface morphology affects the contact surface with other components of the produced device. Si3N4 was synthesized by using low pressure chemical vapour deposition method and depositing single and multi-layer (3 – 5 layers) nanofilms on SiO2 and polycrystalline silicon (PolySi). The total thickness of the synthesized nanofilms was 20 – 60 nm. Surface morphology was investi…
Surface Topographies of Glaucoma Drainage Devices and Their Influence on Human Tenon Fibroblast Adhesion
2010
PURPOSE. This study was performed to investigate the surface topography of different glaucoma drainage devices and to determine the effects of surface roughness on cell adhesion of cultured human tenon fibroblasts.METHODS. The surface topography of four widely used devices (Ahmed FP7 and Ahmed S-2; New World Medical, Inc., Rancho Cucamonga, CA; Baerveldt BG101-350; Advanced Medical Optics, Irvine, CA; and Molteno S1; Molteno Ophthalmic Ltd., Dunedin, New Zealand) was investigated by scanning electron microscopy, and roughness was quantified by white-light confocal microscopy. Cells were grown for 72 hours on the surfaces of implants affixed to standard culture dishes. The cells were labeled…
Stress sensitivity of stylolite morphology
2009
International audience; Stylolites are rough surfaces that form by localized stress-induced dissolution. Using a set of limestone rock samples collected at different depths from a vertical section in Cirque de Navacelles (France), we study the influence of the lithostatic stress on the stylolites morphology on the basis of a recent morphogenesis model. We measured the roughness of a series of bedding-parallel stylolites and show that their morphology exhibits a scaling invariance with two self-affine scaling regimes separated by a crossover-length (L) at the millimeter scale consistent with previous studies. The importance of the present contribution is to estimate the stylolite formation s…