Search results for "Surfaces and interfaces"
showing 10 items of 939 documents
Evidence for the Existence of an Effective Interfacial Tension between Miscible Fluids: Isobutyric Acid-Water and 1-Butanol-Water in a Spinning-Drop …
2006
We report definitive evidence for an effective interfacial tension between two types of miscible fluids using spinning-drop tensiometry (SDT). Isobutyric acid (IBA) and water have an upper critical solution temperature (UCST) of 26.3 degrees C. We created a drop of the IBA-rich phase in the water-rich phase below the UCST and then increased the temperature above it. Long after the fluids have reached thermal equilibrium, the drop persists. By plotting the inverse of the drop radius cubed (r(-)(3)) vs the rotation rate squared (omega(2)), we confirmed that an interfacial tension exists and estimated its value. The transition between the miscible fluids remained sharp instead of becoming more…
Direct measurements of the effects of salt and surfactant on interaction forces between colloidal particles at water-oil interfaces
2007
The forces between colloidal particles at a decane-water interface, in the presence of low concentrations of a monovalent salt (NaCl) and of the surfactant sodium dodecylsulfate (SDS) in the aqueous subphase, have been studied using laser tweezers. In the absence of electrolyte and surfactant, particle interactions exhibit a long-range repulsion, yet the variation of the interaction for different particle pairs is found to be considerable. Averaging over several particle pairs was hence found to be necessary to obtain reliable assessment of the effects of salt and surfactant. It has previously been suggested that the repulsion is consistent with electrostatic interactions between a small nu…
Feeding ecology and chewing mechanics in hoofed mammals: 3D tribology of enamel wear.
2013
11 pages; International audience; Large herbivorous mammals have evolved chewing systems capable of processing a large variety of structurally diverse foods. Three-dimensional (3D) surface texture parameters are applied to investigate wear mechanisms related to tooth morphology, food source, and chewing dynamics. We tested 46 industrial 3D surface texture parameters for their capability to robustly indicate specific biomechanics in two grazing (Blue Wildebeest and Grevy's Zebra) and two browsing (Giraffe and Black Rhinoceros) ungulate mammals. These species inhabit sub-Saharan Africa and represent foregut and hindgut fermenters. The results did not indicate a wavelength threshold that can c…
Studies on atomic layer deposition of IRMOF-8 thin films
2015
Deposition of IRMOF-8 thin films by atomic layer deposition was studied at 260–320 C. Zinc acetate and 2,6-naphthalenedicarboxylic acid were used as the precursors. The as-deposited amorphous films were crystallized in 70% relative humidity at room temperature resulting in an unknown phase with a large unit cell. An autoclave with dimethylformamide as the solvent was used to recrystallize the films into IRMOF-8 as confirmed by grazing incidence x-ray diffraction. The films were further characterized by high temperature x-ray diffraction (HTXRD), field emission scanning electron microscopy, Fourier transform infrared spectroscopy (FTIR), time-of-flight elastic recoil detection analysis (TOF-…
Field-induced tip–sample oxygen transfer in scanning tunneling microscopy on TiO2(110) (1 1).
2008
International audience; A study on the field-induced tip–surface oxygen transfer at room temperature and its influence on the tunneling conditions for stable STM imaging of the TiO2(110) (1 1) surface is reported. A simple model of field-induced transfer is applied to tungsten and platinum–iridium tips. The oxygen transition rates from the sample to the tip or from the tip to the sample depend on the oxygen desorption barriers formed at tunneling distance. For stable imaging the applied bias voltage has to balance the oxygen transfer probabilities in both directions. In the case of Pt/Ir tips, the tunneling conditions for images with clear evidence of bridging oxygen point defects have been…
Silicate and Hydroxide Concentration Influencing the Properties of Composite Al2O3-TiO2 PEO Coatings on AA7075 Alloy
2021
This work evaluates the effect of sodium meta-silicate pentahydrate (SMS) and potassium hydroxide concentrations on properties of Al2O3-TiO2 coatings produced through plasma electrolytic oxidation in a solution containing 3 g L−1 potassium titanyl oxalate, (PTO), using a unipolar waveform with constant current density. The surface and cross-section characteristics of PEO coatings including morphology, elemental distribution, and phase composition were evaluated using FESEM, EDS, and XRD techniques. Voltage-time response indicated the concentration of SMS and KOH had a significant effect on the duration of each stage of the PEO process. More cracks and pores were formed at the higher concent…
Ceramic materials wear mechanisms when cutting nickel-based alloys
1999
Abstract In this paper the performances of some commercial ceramic inserts when cutting AISI 310 steel are investigated and compared to those of a traditional carbide based tool. The most important wear mechanism in the ceramic inserts is related to the segmented edges of the chips that abrade a notch at the end of the cut zone. Alumina–zirconia inserts are very sensitive to this kind of wear, whereas tools made of Sialon and alumina with SiC whiskers exhibit slightly better performances despite the concomitant chemical wear mechanisms.
High Fluorescence of Thioflavin T Confined in Mesoporous Silica Xerogels
2013
Trapping of organic molecules and dyes within nanoporous matrices is of great interest for the potential creation of new materials with tailored features and, thus, different possible applications ranging from nanomedicine to material science. The understanding of the physical basis of entrapment and the spectral properties of the guest molecules within the host matrix is an essential prerequisite for the design and control of the properties of these materials. In this work, we show that a mesoporous silica xerogel can efficiently trap the dye thioflavin T (ThT, a molecule used as a marker of amyloid fibrils and with potential drug benefits), sequestering it from an aqueous solution and pro…
Advanced fragmentation stage of oxide coating on polymer substrate under biaxial tension
2005
Crack patterns of 100-nm-thick silicon oxide coating on polypropylene film subjected to equibiaxial stress loading are studied experimentally. The loading is achieved by means of a bulging cell mounted under an optical microscope with stepwise pressurization of film specimens. The evolution of the coating fragment area distribution at relatively high strains is modeled using Weibull statistics to describe the coating strength. The fragment area distribution at an advanced fragmentation stage is shown to scale with the average fragment area, the latter being a power function of the applied biaxial strain.
Molecular dynamics simulation of epitaxial growth of the Si(001) surface
1988
Abstract Molecular beam epitaxy on a Si(100) substrate has been studied using a molecular dynamics method with the Stillinger-Weber model potential. At high substrate temperature, 800 K, well ordered crystalline layers are found to grow underneath an amorphous overlayer of approximately 5 A thick. A limiting temperature for epitaxial growth is found to be 480 K, below which the growth does not produce ordered layers. When the sample deposited below 480 K is heated up to 800 K and the deposition is started again the original adatoms start to form ordered atomic layers. Thus the collisions of the deposited atoms in addition to the substrate temperature seem to play an essential role in the gr…