Search results for "Surfaces"
showing 10 items of 2837 documents
Molecular modeling studies of interactions between sodium polyacrylate polymer and calcite surface
2013
Abstract The interactions between calcite pigment and sodium polyacrylate dispersing agent, widely used in papermaking as paper coating components, were investigated using classical force field and quantum chemical approaches. The objective was to understand interactions between the calcite surface and sodium polyacrylate polymer at 300 K using molecular dynamics simulations. A quantum mechanical ab initio Hartree–Fock method was also used to obtain detailed information about the sodium polyacrylate polymer structure. The effect of water molecules (moisture) on the interactions was also examined. Calculations showed that molecular weight, branching and the orientation of sodium polyacrylate…
Frictional Drag Mechanisms between Polymer-Bearing Surfaces
2001
The fundamental features of friction between two polymer-bearing surfaces in relative sliding motion are investigated by molecular dynamics simulation. Adsorbed and grafted polymers are considered in good and bad solutions. The solvent is not treated explicitly but indirectly in terms of a Langevin thermostat. In both systems, we observe shear thinning that is attributed to an orientation of the radius of gyration along the sliding direction. This effect is particularly strong for surfaces bearing polymer brushes. In this case, the shear stresses are mainly determined by the degree of the interpenetration of brushes.
Photoinduced electron transfer in molecular organizates at the gas-water interface
1994
Abstract The influence of the molecular geometry is of fundamental importance for a better understanding of the photoinduced electron transfer mechanism. Because of their typical molecular structures, cyclophane rings have proved to be suitable for this purpose as electron acceptor molecules adsorbed under an amphiphile monolayer. We used a pyrene-labelled phospholipid derivative both as molecular anchor for the cyclophane ring and electron donor molecule. The co-spreading technique was used to prepare the complex monolayers. Surface pressure and surface potential measurements have indicated similar monolayer behaviour as with dimyristoylphosphatidic acid as anchor molecule, leading to the …
Structure and Yielding of Colloidal Silica Gels Varying the Range of Interparticle Interactions.
2016
The relationship between interaction range, structure, fluid-gel transition, and viscoelastic properties of silica dispersions at intermediate volume fraction, Φv ≈ 0.1 and in alkaline conditions, pH = 9 was investigated. For this purpose, rheological, physicochemical, and structural (synchrotron-SAXS) analyses were combined. The range of interaction and the aggregation state of the dispersions were tuned by adding either divalent counterions (Ca(2+)) or polycounterions (PDDA). With increasing calcium chloride concentration, a progressive aggregation was observed which precludes a fluid-gel transition at above 75 mM of calcium chloride. In this case, the aggregation mechanism is driven by s…
On the tribology and rheology of polymer brushes in good solvent conditions: a molecular dynamics study
2003
Tribological and rheological properties of two polymer brushes in relative sliding motion and good solvent conditions are investigated by means of molecular dynamics (MD) simulations. The lateral forces between the brushes are found to decrease logarithmically with increasing relative sliding velocity v0 over a range of more than one decade in v0. We also observe an almost logarithmic relaxation of the end-to-end distance vector that occurs after sliding is stopped. The coincidence of these logarithmic dependencies support the picture that friction between polymer brushes is small due to the retraction of the polymers from the interpenetration zone. The shear stress relaxes almost instantly…
Mechanism of Trichloroethene Hydrodehalogenation: A First-Principles Kinetic Monte Carlo Study
2014
A hydrodehalogenation (HDC) reaction of trichloroethene (TCE) has gained a lot of interest due to its possible application in water purification, but the reaction mechanism has been subject to much controversy. In this work, HDC of TCE on Pd(111) was examined by carrying out kinetic Monte Carlo simulations based on DFT-calculated thermodynamic and kinetic parameters. Obtained kMC results show that the HDC follows a so-called direct pathway, which means that, after adsorption on a catalyst, TCE quickly dechlorinates, producing CH–C and then, more slowly, hydrogenates to form hydrocarbon products. This is reflected in the surface coverage snapshots, where intermediates corresponding to the di…
Impact of aggregates on excitation dynamics in transparent polymer films doped by dipolar molecules
2008
Abstract Optical properties of transparent polymer films of polymethylmethacrylate doped (up to 25 wt.%) by dipolar N , N -dimethylaminobenzylidene 1,3-indandione (DMABI) molecules were studied. Formation of DMABI nanocrystallites, increasing in their density and size with dopant concentration, was revealed by optical microscopy. Transformation of the fluorescence spectrum from the molecular-like emission (for the low dopant concentration below 1 wt.%) to highly red-shifted fluorescence corresponding to self-trapped excitons in the crystallites was observed. It was shown, that due to the resonant energy transfer in the blend, the DMABI nanocrystals can serve as efficient fluorescence marker…
Aggregation Processes and Formation of Silico-calco-alkaline Gels under High Ionic Strength
2002
This paper presents a systematic in situ study of the process of formation of silico-calco-alkaline gels starting from a liquid colloidal solution containing different alkaline ions and different calcium concentration until the final gel state. The combined use of X-ray and neutron small-angle scattering (SAS) and dynamical rheometry techniques lead to a consistent description of the structure of the aggregates and of the mechanisms of aggregation involved in gel formation. SAS results indicate that the aggregates are fractal objects, their structure strongly depending on calcium ion concentration. The differences in gelation kinetics for systems containing different alkaline ions were attr…
Polysarcosine-containing copolymers: Synthesis, characterization, self-assembly, and applications
2018
Although the first polysarcosine (pSar) synthesis by Wesseley et al. was reported almost a century ago, it was only recently that pSar gained broader attention and is considered a potential alternative of poly(ethylene glycol) (PEG). In contrast to polyethers, such as PEG, pSar is a polypeptoid based on the amino acid sarcosine, i.e. N-methylated glycine. As a polymer, pSar combines PEG-like properties, e.g., excellent solubility in water, protein resistance, low cellular toxicity and a non-immunogenic character, while being based on endogenous material. Sarcosine can be obtained in a simple one-step reaction of bromoacetic acid and methylamine, easily transferred into the sarcosine N-(thio…
No-Flow Temperature in Injection Molding Simulation
2010
Most injection molding simulation packages use the no-flow temperature (NFT) as a means of determining whether the polymer flows or is solid. The NFT is not well defined, and a standard method for measuring it does not exist. A sensitivity analysis of the filling stage has been carried out with two different packages [VISI Flow (Vero Software Limited, Gloucestershire, UK) and Moldflow (Autodesk, Inc., San Rafael, CA)] to estimate the influence of the NFT on the main processing parameters. The NFT has a large influence on the thickness of the frozen layer, but it does not appreciably affect the filling pressure. Because the NFT affects the frozen layer, an effect on the estimation of shrinka…