Search results for "T method"
showing 10 items of 1254 documents
Analysis of industry 4.0 implementation in mobility sector: An integrated approach based on QFD, BWM, and stratified combined compromise solution und…
2022
Journal of industrial integration 30, 100406 (2022). doi:10.1016/j.jii.2022.100406 special issue: "Data/Information Integration Techniques in Industry 4.0/5.0 / Edited by Shahid Mumtaz, Syed Hassan, Mohsen Guizani, Muhammad Ikram"
Simulation of granular organic fertilizer application by centrifugal spreader
2021
There is no specialized equipment designed to spread granular cylindrical organic fertilizer in the soil. There are also no rational recommendations available on how to spread this type of fertilizer. Mineral fertilizer spreaders are most often used for spreading granulated organic fertilizer. However, these fertilizers are significantly different from mineral fertilizers. Due to these differences, organic granular fertilizers often are spread unevenly, and the fertilizer does not reach the required working width. Furthermore, the rate of spreading is not accurate, and the fertilizer is often crushed too much. The objective of this research is to develop a simulation model for granular orga…
Crimping Profile Optimization on the Air Spring Using Finite Element Method
2018
Abstract Due to the fact that the requirements of the industry aim to improve the dynamics, the safety and the comfort during the use of the vehicles, it is recommended to use the finite element method for component quality optimization. The purpose of this paper is to provide an overview of the current state of analysis through the finite element method of the crimping process used to assemble air springs produced in the automotive industry. Starting from the prototype of an air spring, the researches are focused on the study of the assembly of the piston with the bellow and the crimping ring through the crimping process. After analysis with the finite element method and static tests, impr…
Revisited mixed-value method via symmetric BEM in the substructuring approach
2012
Abstract Within the Symmetric Boundary Element Method, the mixed-value analysis is re-formulated. This analysis method contemplates the subdivision of the body into substructures having interface kinematical and mechanical quantities. For each substructure an elasticity equation, connecting weighted displacements and tractions to nodal displacements and forces of the same interface boundary and to external action vector, is introduced. The assembly of the substructures is performed through both the strong and weak regularity conditions of the displacements and tractions. We obtain the solving equations where the compatibility and the equilibrium are guaranteed in the domain Ω for the use of…
Simulation of laser-generated ultrasonic wave propagation in solid media and air with application to NDE
2009
Ultrasonic methods are well known as powerful and reliable tool for defect detection. In the previous decades focus and interest have been directed to non-contact sensors and methods, showing many advantages over contact techniques where inspection depends on contact conditions (pressure, coupling medium, contact area). The non-contact hybrid ultrasonic method described here is of interest for many applications, requiring periodic inspection in service or after manufacturing. Despite the potential impact of laser-generated ultrasound in many areas of industry, robust tools for studying the phenomenon are lacking and thus limit the design and optimization of non-destructive testing and evalu…
Masonry structures subjected to tsunami loads: Modeling issues and application to a case study
2020
Abstract Tsunamis are among the most dangerous natural disasters for coastal areas experiencing tsunami hazard. One of the major concerns in the assessment of strategies for the risk mitigation is to estimate vulnerability of structures and infrastructures. However, reliable approaches for the evaluation of the structural capacity under tsunami loads are nowadays not always available for all the types of structures, especially masonry. On this aim, the paper deals with the modeling issues of 3D masonry structures subjected to tsunami loads and the effect on the structural behavior of different modeling approaches. First, a brief state of the art on the available studies is presented regardi…
A Viscoelastic Model for the Long-Term Deflection of Segmental Prestressed Box Girders
2017
Most of segmental prestressed concrete box girders exhibit excessive multidecade deflections unforeseeable by past and current design codes. To investigate such a behavior, mainly caused by creep and shrinkage phenomena, an effective finite element (FE) formulation is presented in this article. This formulation is developed by invoking the stationarity of an energetic principle for linear viscoelastic problems and relies on the Bazant creep constitutive law. A case study representative of segmental prestressed concrete box girders susceptible to creep is also analyzed in the article, that is, the Colle Isarco viaduct. Its FE model, based on the aforementioned energetic formulation, was succ…
Topology Optimization Design of Internal Reinforcements in a Sailing Dinghy
2021
AbstractIn this paper, a novel approach has been followed based on FEM simulation and Topology Optimization tools to locate and model the reinforcements inside the hull of a sailing dinghy. This process assumes that the inner volume included between the hull and the deck is, at the beginning of the simulation, filled with material; then a portion of this inner volume is eroded until a final free form shape of the reinforcements is obtained. A key point of this procedure is the definition of the optimization constrains because the final shape of the reinforcements must fulfill several requirements such as weight, stiffness and stress. At the end of the optimization procedure, the final shape…
Structural assessment of the EU-DEMO WCLL Central Outboard Blanket segment under normal and off-normal operating conditions
2021
Abstract Within the framework of the EUROfusion design activities concerning the EU-DEMO Breeding Blanket (BB) system, a research campaign has been carried out at the University of Palermo with the aim of investigating the structural behaviour of the DEMO Water-Cooled Lithium Lead (WCLL) Central Outboard Blanket (COB) segment. The assessment has been performed considering three different loading scenarios: the Normal Operation (NO), the Over-Pressurization (OP) and the Upward Vertical Displacement Event (VDE-up). In particular, NO scenario represents the loading case referring to the nominal operating conditions, whereas the OP scenario refers to the loading conditions due to an in-box LOCA…
Maximum Displacement Variability of Stochastic Structures Subject to Deterministic Earthquake Loading
1998
The variability of the maximum response displacement of random frame structures under deterministic earthquake loading are examined in this paper using stochastic finite element techniques. The elastic modulus and the mass density are assumed to be described by cross-correlated stochastic fields. Specifically, a variability response function formulation is used for this problem, which allows for calculation of spectral-distribution-free upper bounds of the maximum displacement variance. Further, under the assumption of prespecified correlation functions describing the spatial variation of the material properties, variability response functions are used to calculate the corresponding maximum…