Search results for "TFM"
showing 10 items of 11 documents
Ultrasonic phased array inspection of a Wire + Arc Additive Manufactured (WAAM) sample with intentionally embedded defects
2019
In this study, Wire + Arc Additive Manufacture (WAAM) was employed to manufacture a steel specimen with intentionally embedded defects which were subsequently used for calibration of an ultrasonic phased array system and defect sizing. An ABB robot was combined with the Cold Metal Transfer (CMT) Gas Metal Arc (GMA) process to deposit 20 layers of mild steel. Tungsten-carbide balls (ø1-3 mm) were intentionally embedded inside the additive structure after the 4th, 8th, 12th and 18th layers to serve as ultrasonic reflectors, simulating defects within the WAAM sample. An ultrasonic phased array system, consisting of a 5 MHz 64 Element phased array transducer, was used to inspect the WAAM sample…
Estimating economic severity of Air Traffic Flow Management regulations
2021
The development of trajectory-based operations and the rolling network operations plan in European air traffic management network implies a move towards more collaborative, strategic flight planning. This opens up the possibility for inclusion of additional information in the collaborative decision-making process. With that in mind, we define the indicator for the economic risk of network elements (e.g., sectors or airports) as the expected costs that the elements impose on airspace users due to Air Traffic Flow Management (ATFM) regulations. The definition of the indicator is based on the analysis of historical ATFM regulations data, that provides an indication of the risk of accruing dela…
Using coded excitation to maintain signal to noise for FMC+TFM on attenuating materials
2019
Ultrasonic Non-Destructive Evaluation using Full Matrix Capture (FMC) and Total Focusing Method (TFM) is used for high resolution imaging as every pixel is in optimal focus. FMC excites one element in turn, so operates with lower transmitted energy compared to phased array beamforming. The energy at a reflector is further reduced by the broad directivity pattern of the single element. The large number of Tx/Rx A-scans that contribute to each pixel recover the Signal-to-Noise Ratio (SNR) in the final TFM image. Maintaining this in the presence of attenuating materials is a challenge because relevant information in each A-scan signal is buried in the thermal noise, and the TFM process assumes…
Transient Electrical Behaviour of the TF Superconducting Coils of Divertor Tokamak Test Facility During a Fast Discharge
2022
The paper is focused on the electromagnetic analysis of the Toroidal Field (TF) superconducting coils of the Divertor Tokamak Test facility (DTT) when electrical transients occur in the TF coils system: for example, during the operations of the Fast Discharge Units (FDUs) and considering also, the simultaneous occurrence of a fault condition. During the FDU intervention, a transient voltage excitation lasting few microseconds occurs at the TF coil terminals and it electrically stresses the insulations of TF coils itsef. To investigate the voltage distribution across, inside and between different Double Pancakes (DPs) of each TF coil, a lumped parameters circuital model has been developed an…
Determination of Bubble Size Distribution Using Ultrasound Array Imaging
2020
In this article, ultrasonic phased arrays are deployed as an imaging tool for industrial process analysis. Such arrays are typically used for sonar, medical diagnosis, and nondestructive testing; however, they have not yet been applied to industrial process analysis. The precise positioning of array elements and high frequencies possible with this technology mean that highly focused images can be generated, which cannot currently be achieved using ultrasound tomography. This article aims to highlight the potential of this technology for the measurement of bubble size distribution (BSD) and to demonstrate its application to both intrusive and noninvasive process measurements. Ultrasound imag…
Intentional weld defect process: From manufacturing by robotic welding machine to inspection using TFM phased array
2019
Specimens with intentionally embedded weld defects or flaws can be employed for training, development and research into procedures for mechanical property evaluation and structural integrity assessment. It is critical that the artificial defects are a realistic representation of the flaws produced by welding. Cylindrical holes, which are usually machined after welding, are not realistic enough for our purposes as it is known that they are easier to detect than the naturally occurring imperfections and cracks. Furthermore, it is usually impractical to machine a defect in a location similar to where the real weld defects are found. For example, electro-discharge machining can prod…
Ultrasonic phased array inspection of wire plus arc additive manufacture samples using conventional and total focusing method imaging approaches
2019
In this study, three aluminium samples produced by wire + arc additive manufacture (WAAM) are inspected using ultrasonic phased array technology. Artificial defects are machined using a centre drill, ø 3 mm, and electrical discharge machining (EDM), ø 0.5-1 mm, in a cylindrical through-hole topology. The samples are first inspected using a single-element wheel probe mounted on a KUKA robot in order to investigate the feasibility of using a conventional ultrasonic transducer approach. Unfortunately, the wheel probe is found to be unsuitable for scanning the WAAM specimens and ultrasonic phased arrays are employed next. The set-up includes 5 MHz and 10 MHz arrays (128 elements) in direct cont…
Ultrasonic phased array inspection of wire plus arc additive manufacture (WAAM) samples using conventional and total focusing method (TFM) imaging…
2018
In this study, three aluminium samples produced by wire + arc additive manufacture (WAAM) are inspected using ultrasonic phased array technology. Artificial defects are machined using a centre drill, ø3 mm, and electro-discharge machining (EDM), ø0.5-1 mm, in a cylindrical through hole topology. The sample was first inspected by a single element wheel probe mounted on a KUKA robot in order to investigate the feasibility of using a conventional ultrasonic transducer approach. Unfortunately, the wheel probe was found to be unsuitable for scanning of the WAAM specimens and ultrasonic phased arrays were employed next. The setup included 5 MHz and 10 MHz arrays (128 elements) in direct contact w…
Orientaciones para la elaboración de trabajos de investigación en educación especial
2019
El presente trabajo expone una serie de recomendaciones y orientaciones para la elaboración de trabajos de investigación en educación especial. Se trata de un material dirigido a estudiantes que se enfrentan por primera vez a la realización de un trabajo de investigación en este ámbito, como es el caso de la realización de los trabajos de final de grado o de máster.
Guía accesible de recursos útiles para realizar el Trabajo de Fin de Grado y el Trabajo de Fin de Máster
2020
Se presenta un material accesible con recursos y herramientas para realizar el TFG y el TFM que sirva de apoyo a estudiantes y profesorado. Se ofrece información de cómo usar el gestor bibliográfico Mendeley, los estilos de Word para realizar tablas de contenido, y el programa de encuestas LimeSurvey. Se incluyen en el documento enlaces a mini-vídeos explicativos accesibles (subtitulados) relacionados con todas estas cuestiones. Asimismo, se recomienda el uso de los buscadores de la Universitat y se tratan cuestiones como el uso de lenguaje inclusivo, política de protección de datos, herramientas para el correcto uso del valenciano y el inglés, información sobre competencias profesionales, …