Search results for "TRIX"
showing 10 items of 3314 documents
Non-conventional synthesis and photophysical studies of platinum(ii) complexes with methylene bridged 2,2′-dipyridylamine derivatives
2019
Methylene bridged 2,2′-dipyridylamine (dpa) derivatives and their metal complexes possess outstanding properties due to their inherent structural flexibility. Synthesis of such complexes typically involves derivatization of dpa followed by coordination on metals, and may not always be very efficient. In this work, an alternative synthetic approach, involving the derivatization step after – rather than prior to – coordination of dpa on metal center, is proposed and applied to synthesis of a number of platinum(II) complexes with substituted benzyldi(2-pyridyl)amines. Comparison with the more conventional synthetic route reveals greater efficiency and versatility of the proposed approach. The …
Asymptotic and numerical studies of electron scattering in 2D quantum waveguides of variable cross-section
2012
Analysis of FBG reflection spectra under uniform and non-uniform transverse loads
2019
Loads applied transversely on the external surface of waveguides change their circular cross-sectional geometry generating birefringence. Due to this effect the reflected spectrum of a Fibre Bragg grating (FBG) undergoes a splitting of the single peak of the Bragg wavelength. In this work, we employed the Transfer Matrix Method (TMM) for x- and y-polarized wave-modes to model the uniform FBG reflection spectra for uniform and non-uniform transverse loads. We also performed experimental measurements for two different transverse load scenarios. The load profiles chosen for these experiments were applied on the FBG sensor through a block of steel and a roll bearing pin. Then, the modelled and …
Polymorphic chiral squaraine crystallites in textured thin films
2020
Chirality 32(5), 619 - 631 (2020). doi:10.1002/chir.23213
The role of the matrix-filler affinity on morphology and properties of polyethylene/clay and polyethylene/ compatibilizer/clay nanocomposites drawn f…
2009
In this work the structural variations and mechanical performance of polyethylene/clay nanocomposite drawn fibres, also in the presence ofcompatibilizer, such as a commercial maleic anhydride grafted polyethylene, PEgMA, was studied. In the isotropic state both systems show intercalated morphology.After spinning and cold drawing, by adding the nanoparticles, the tensile strength as a function of the draw ratio increases and this rise is more pronounced for the filled compatibilized system. The reduction of the elongation at break, on the contrary, is about the same for all the examined samples. The orientation of the macromolecules, evaluated by measurements of the birefringence and calorim…
Recycling ground tire rubber (GTR) scraps as high-impact filler of in-situ produced polyketone matrix
2014
Performances Recovery of Flax Fiber Reinforced Composites after Salt-Fog Aging Test
2022
In the present paper, the performance recovery under conditions of discontinuous exposure to a marine environment of a natural fiber-reinforced composite (NFRC) reinforced by flax fibers was assessed. In particular, this laminate was initially exposed to salt-fog for 15 and 30 days, and then stored in a controlled air condition for up to 21 days. The flax fiber-reinforced composite showed coupled reversible and irreversible aging phenomena during the wet stage, as well as evidencing a significant mechanical recovery during the dry stage. Unlike the stiffness, the laminate showed a noticeable recovery of its flexural strength. This behavior affected the composite material toughness. A simpli…
Physical and chemical interactions involved in several flavour compounds/food matrix systems
2002
National audience; Food-matrix components, such as proteins, polysaccharides, and lipids interact with flavour compounds in different ways. Proteins bind flavour compounds mostly by hydrophobic interactions and possible hydrogen bonding, as illustrated by molecular visualisation. Addition of fat induces a great retention of hydrophobic compounds, which depend on the nature of fat, degree of unsaturation, hydrophobic chain length of fatty acids. Addition of hydrocolloids modifies the release of hydrophobic aroma compounds, due to a lower diffusion in the matrix. In jellified systems, gel structure not only affects partition coefficients but also mass transfer coefficients of flavour compound…
Selective Laser Sintering of Metal-Organic Frameworks: Production of Highly Porous Filters by 3D Printing onto a Polymeric Matrix.
2019
Metal‐organic frameworks (MOFs) have raised a lot of interest, especially as adsorbing materials, because of their unique and well‐defined pore structures. One of the main challenges in the utilization of MOFs is their crystalline and powdery nature, which makes their use inconvenient in practice. Three‐dimensional printing has been suggested as a potential solution to overcome this problem. We used selective laser sintering (SLS) to print highly porous flow‐through filters containing the MOF copper(II) benzene‐1,3,5‐tricarboxylate (HKUST‐1). These filters were printed simply by mixing HKUST‐1 with an easily printable nylon‐12 polymer matrix. By using the SLS, powdery particles were fused t…
BUILDING THE PROJECT TEAM AND PROJECT ORGANIZATION – CHALLENGES AND OBSTACLES
2011
The building of a project team can be one of the first hurdles the future team manager faces. The blame for this can be constraints in terms of resources to fund salaries, lack of adequate or properly trained personnel, unavailability of specialists the manager needs within the project in the period this is scheduled, but also other causes. The building of a project team process must also correlated with its future structure, the two components influencing each other in both directions. Choosing an appropriate structure for the project to be implemented is not only necessary, but, moreover, may prove fatal to the extent that is not obtained.