Search results for "Template"
showing 10 items of 205 documents
Anodic alumina membranes as template for the synthesis of 1-D metal oxide and hydroxide nanostructures
2008
Anodic alumina membranes with highly ordered cylindrical pores and tuneable geometry have been prepared (pore diameters=20−200 nm; pore density 1012-1014 pores/m2; thickness: 20-100 mm) by controlling the anodizing process of aluminum in phosphoric, oxalic and sulphuric acid. The influence of different parameters (initial treatment of aluminium surface, composition of electrolyte, temperature and applied potential) on the final characteristics of the membranes have been investigated. The use anodic alumina membranes as template for the electrosynthesis of some metal hydroxides and oxides 1-D nanostructures (nanowires and nanotubes) will be also proved.
One-step electrochemical synthesis and physico-chemical characterization of CdSe nanotubes
2013
Abstract Stoichiometric CdSe nanotubes (NTs) with a length of ∼700 nm have been successfully grown by one-step electrochemical technique into anodic alumina membranes. Cyclovoltammetric method has been performed using porous anodic alumina as template electrode and an electrochemical bath containing Cd 2+ ions and SeO 2 . The as-prepared NTs have been identified as face-centred-cubic CdSe by XRD, while micro-Raman analysis reveals the typical peaks of nanostructured CdSe. The stoichiometric deposition of CdSe NTs formation is suggested by EDX analysis, with an average atomic percentage of Cd:Se of ∼0.93. Photoelectrochemical measurements reveal that CdSe NTs are photoactive materials with d…
High-performance of PbO2 nanowire electrodes for lead-acid battery
2014
Abstract PbO2 nanowires were obtained by template electrodeposition in polycarbonate membranes and tested as positive electrode for lead-acid battery. Nanowires were grown on the same material acting as current collector that was electrodeposited too. The nanostructured electrodes were assembled in a zero-gap configuration using commercial negative plate and separator. Cell performance was tested by galvanostatic charge/discharge cycles in a 5 M H2SO4 aqueous electrolyte. PbO2 nanostructured electrodes were able to deliver at 1C rate an almost constant capacity of about 190 mAh g−1 (85% of active material utilization), close to the theoretical value (224 mAh g−1). The nanowire array provide…
Ni alloy nanowires as high efficiency electrode materials for alkaline electrolysers
2021
Abstract The fabrication and characterization of nickel-alloy electrodes for alkaline electrolysers is reported. Three different alloys (Ni–Co, Ni–Zn and Ni–W) at different composition were studied in order to determine the optimum condition. Nanostructured electrodes were obtained by template electrodeposition into a nanoporous membrane, starting from aqueous solution containing the two elements of the alloy at different concentrations. Composition of alloys can be tuned by electrolyte composition and also depends on the difference of the redox potential of elements and on the presence of complexing agents in deposition bath. Electrochemical and electrocatalytic tests, aimed at establishin…
Photoelectrochemical characterization of Cu2O-nanowire arrays electrodeposited into anodic alumina membranes
2007
Perfectly aligned nanowire arrays of polycrystalline Cu2O were grown by template-pulsed electrodeposition from a cupric acetate-sodium acetate bath into anodic alumina membranes (AAM). The photoelectrochemical behavior of arrays with different nanowire lengths (0.5 mu m and 2 mu m) was investigated in neutral solution, and the results compared to those pertaining to Cu2O films grown with the same procedure. Although all samples displayed the same indirect bandgap (similar to 1.9 eV), differences were observed both in photocurrent intensity and sign. The latter changed with potential and wavelength in different ways for nanowires and films, revealing a different defect concentration in the t…
Periodic nanoscale patterning of polyelectrolytes over square centimeter areas using block copolymer templates
2016
© The Royal Society of Chemistry 2016. Nano-patterned materials are beneficial for applications such as solar cells, opto-electronics, and sensing owing to their periodic structure and high interfacial area. Here, we present a non-lithographic approach for assembling polyelectrolytes into periodic nanoscale patterns over cm2-scale areas. Chemically modified block copolymer thin films featuring alternating charged and neutral domains are used as patterned substrates for electrostatic self-assembly. In-depth characterization of the deposition process using spectroscopy and microscopy techniques, including the state-of-the-art scanning transmission X-ray microscopy (STXM), reveals both the sel…
Rapid One-Step Fabrication of Graphene Oxide-Decorated Polycaprolactone Three-Dimensional Templates for Water Treatment
2020
Coating of flexible substrates is crucial to prepare versatile, multifunctional materials. However, exploration of effective fabrication approaches is still a challenging issue, because the pathways generally proposed require time-consuming, multistep protocols. Here, we developed a one-pot process for decorating either pearl necklace-like or fibrous fluffy-like structures of polycaprolactone (PCL) with graphene oxide (GO) skin. PCL solutions were dry jet-wet electrosprayed or electrospun into a stirred liquid collector constituted by ethanol-containing GO nanoparticles. The stirred liquid collector enables the formation of 3D-structures, whose microarchitecture can be designed by controlli…
Total oxidation of VOCs on mesoporous iron oxide catalysts: Soft chemistry route versus hard template method
2016
9 figures, 3 tables.-- Supplemantary information available
Application of electrochemical impedance for characterising arrays of Bi2S3 nanowires
2015
Abstract Electrochemical Impedance Spectroscopy (EIS) was used to characterise the electrical properties of bismuth sulphide (Bi2S3) nanowires (NWs) templated within anodic aluminium oxide (AAO) membranes. A specially engineered cell, with a nominal electrolyte volume of 0.1–0.2 ml, was used to hold and measure the electrochemical impedance of the fragile NW/AAO samples. An equivalent circuit model was developed to determine the filling density of nanowires within the porous templates. The EIS method can be utilised to probe the nanowire filling density in porous membranes over large sample areas, which is often unobtainable using electron microscopy and conductive atomic force microscopy t…
Precipitation synthesis of magnetite Fe3O4 nanoflakes
2014
Precipitation can be applied to synthesize magnetite Fe3O4 nanoflakes in an ambient air atmosphere without using any surfactant, templates or special equipment. Magnetite nanoflakes were precipitated from only Fe2+ chloride solution without adding Fe3+. The formation of Fe3O4 nanoflakes is suggested to occur due to formation of an intermediate goethite phase, thus providing anisotropic crystal growth. Compared to other methods, the method presented here is fast and suitable for large scale synthesis.