Search results for "Thermal Analysis"

A green method to prepare nanosilica modified graphene oxide to inhibit nanoparticles re-aggregation during melt processing

2017

Abstract A graphene oxide-silica nanohybrid (GOS), self-assembled into a lasagna -like structure, was prepared in water and used as a filler for the melt preparation of polyamide 6 (PA6)-based nanocomposites. For sake of comparison, PA6-based materials were prepared under the same processing conditions by adding GO only or a physical mixture of GO and silica (GO+S). All the materials were characterized from a morphological, spectroscopic, thermal, dynamic-mechanical (DMA) and mechanical point of view. For all the nanocomposites, the interphase was studied either by analyzing loss factor plots coming from DMA measurements and by implementing a novel approach, i.e. combining solvent extractio…

Li2OSiO2Al2O3MeIIO Glass-Ceramic Systems for Tile Glaze Applications

1991

In order to verify the possibility of using glass-ceramic materials as tile coatings, the devitrification processes of three industrial formulations belonging to the Li2O─Al2O3─SiO2 glass-ceramic system were investigated by differential thermal analysis, X-ray diffractometry, scanning electron microscopy, and IR spectroscopy. Compositional variations were made by addition of large amounts of MgO or CaO or PbO (ZnO) oxides as well as through smaller additions of other oxides. In these systems the surface crystallization contributes appreciably to the bulk crystallization mechanism. All the systems investigated show a high tendency toward crystallization even at very high heating rates, devel…

Thermal and infrared spectroscopic characterization of historical mortars

1998

Abstract The characterization of historical mortars was performed by thermal analysis (TG-DTG), simultaneous infrared spectroscopy (TG-FTIR) and inductively coupled plasma atomic emission spectrometry (ICP-AES). The samples were taken from St. John Church (Tartu, Estonia), built in the 13th–14th centuries. The analyses are important for the restoration of the church. In reality, mortar is a very difficult system, the lime is accompanied with different hydraulic components. TG-DTG analysis and FTIR methods can be used to identify various components of mortar and to observe the reactions associated with the controlled heating at 25–900°C in dynamic air and nitrogen atmosphere. The elemental c…

Investigation of eutectic transformation of Zn−Al alloy by DTA

1995

The paper discusses the investigation of crystallization of metals and alloys by differential thermal analysis (DTA). It was assumed that this method allows determination of the mechanism and kinetics of volumetric crystallization underiso conditions (e.g. anisothermal) on the basis of the parameters of the equation expressing an integral form of the DTA curve. From DTA, a course of eutectic transformation was determined for a technical Zn−Al alloy containing 4wt% Al. Investigations were carried out under continuous cooling at various rates and the kinetics parameters were determined with the KEKAM equation:-ln(1-x)=kln

Effects of ZrO2 precursors on the synthesis of V-ZrSiO4 solid solutions by the sol-gel method

1992

The preparation of V-ZrSiO4 solid solutions starting from different ZrO2 precursors by using sol-gel methods is reported. The starting materials were hydrolysed and the dried gels were fired at a temperature between 500 and 900 °C with soaking times of 12h. The organic character of zirconia precursors was stronger, i.e. the starting material had more carbon atoms, a higher temperature was necessary to make the first crystalline phase appear (ZrO2(tetragonal)) and the temperature range for the whole phase transformation was narrower. In all dried gel samples the presence of infrared bands which might be associated with either Si-O-Zr or Si-O-V was not observed. On the other hand, some bands …

Effect of hydrothermal ageing on the thermal and delamination fracture behaviour of CFRP composites

2014

Abstract This work investigates the hydrothermal ageing behaviour of a carbon fibre reinforced laminate and its epoxy matrix in bulk conditions. A model DGEBA epoxy is employed, and water uptake and dynamic mechanical thermal (DMTA) analyses have been performed on both the composites and bulk resin. Fracture toughness of the bulk resin has been measured, evidencing a substantially unmodified critical stress intensity factor KIC, although the evidence of plasticisation effects given by DMTA. Interlaminar Mode I fracture toughness of the composite showed a variable trend towards slight decreases or slight increases, according to the prevailing toughening or embrittling mechanisms activated by…

Layered-structural monoclinic–orthorhombic perovskite La2Ti2O7 to orthorhombic LaTiO3 phase transition and their microstructure characterization

2014

The layered-structural ceramics, such as lanthanum titanate (La{sub 2}Ti{sub 2}O{sub 7}), have been known for their good temperature and low dielectric loss at microwave frequencies that make them good candidate materials for high frequency applications. However, few studies have been conducted on the synthesis optimization by sol gel reaction, in particular by acrylamide polymerization route. The interest in La{sub 2}Ti{sub 2}O{sub 7} ceramic has been greatly increased recently due to the effect of oriented grains. This anisotropy of the microstructure leads to anisotropy in dielectric, electrical and mechanical properties. In this study, grain oriented lanthanum titanate was produced by t…

Electromagnetic-thermal analysis of a hybrid switched-reluctance motor

2002

Effect of additives on the crystallization of cordierite-based glass-ceramics as glazes for floor tiles

2003

Abstract The effect of several additives such as fluxes and/or nucleants on a parent glass with composition located in the primary field of cordierite within the quaternary system CaO–MgO–Al 2 O 3 –SiO 2 has been examined. Crystallization path of glasses was determined by differential thermal analysis (DTA) and X-ray powder diffraction (XRD). Pressed pellets of powdered glasses containing different additives were submitted at thermal treatments up to 1200 °C. The microstructural development at several temperatures was followed by field emission scanning electron microscopy and energy-dispersive X-ray analysis. The results shown that additions of TiO 2 as nucleant and/or B 2 O 3 as flux to a…

Low-temperature Ti-containing 3:2 and 2:1 mullite nanocrystals from single-phase gels

2007

Abstract TiO 2 -containig single-phase gels with (Al 2 O 3  + TiO 2 )/(SiO 2 ) molar ratios 3/2 and 2/1 were prepared by gelling mixtures of aluminium nitrate, tetraethylorthosilicate and titanium isopropoxide. Gels were fast heated at several temperatures up to 1100 °C. Dried and heated gels were characterized by differential thermal analysis (DTA), magic angle spinning nuclear magnetic resonance (MAS-NMR), X-ray powder diffraction (XRD), and scanning and transmission electron microscopies (SEM and TEM). Coupled DTA and XRD results of gels fast heated at 900 °C showed the crystallisation of two mullites as well as a small amount of alumina-silica spinel. 27 Al NMR spectra showed the format…