Search results for "Thermal"
showing 10 items of 3576 documents
Solid State NMR Spectroscopy Investigation of the Molecular Structure of Epoxy Based Materials Cured in Different Conditions
2012
In this work two epoxy resin model systems, whose monomers are typically used in structural composites, were thermally cured in different cure conditions in order to obtain different cross-linking densities. Their molecular structures were investigated through solid state NMR spectroscopy in order to correlate them to the cure process conditions used and the results were discussed in the light of the dynamical mechanical thermal analysis (DMTA) performed.
Aging, rejuvenation, and memory phenomena in a lead-based relaxor ferroelectric
2002
Isothermal aging and temperature cycle experiments were done on the relaxor ferroelectric lead magnesium niobate mixed with 10% lead titanate (PMN-10PT) around and below the diffuse maximum of the dielectric loss. With increasing aging time tw the isothermal evolution of the linear susceptibility follows a power law and does not show frequency scaling. The non-linear susceptibility, however, obeys nearly perfect ωt w-scaling. After aging the sample at a single temperature we observed both rejuvenation and memory effects in temperature cycle experiments. This observation indicates symmetric behavior in the sense that it shows up irrespective of whether cooling with subsequent re-heating or h…
Polylactide-based self-reinforced composites biodegradation: Individual and combined influence of temperature, water and compost
2018
[EN] Self-reinforced polymer composites (SRCs) are proposed as a suitable alternative for composite development, based in the combination of a polymeric matrix and a polymeric fibre made of the same polymer. SRCs based in polylactide (PLA) could be fully biodegradable and their valorisation routes could presumably be assimilated to those for neat PEA. In this sense, the aim of this study was to develop new self-reinforced PLA-based composites and ascertain their biodegradability. For this purpose, PLA-based SRCs were obtained through a thermo-compression procedure and their biodegradability corroborated under standard conditions (ISO 20200). Moreover, a deep study of the effect of the diffe…
Quantification of low levels of amorphous content in maltitol
2004
A method for the quantification of low levels of amorphous content of maltitol with hyper-DSC (high speed DSC) was developed. The method is based on the fact that the change of specific heat ( � Cp) at the glass transition is linearly proportional to the amorphous content. Twelve synthetic mixtures with various degrees of crystalline and amorphous maltitol were prepared. � Cp was determined at both fictive and
Insights into localized manipulation of organogel-related microcrystalline spherulite formation
2015
Abstract The formation processes of microcrystalline spherulitic fiber systems related to bile acid amides were determined to include dominant interface-related aspects, the role of which were studied in terms of potential manipulation and increased control over the overall structure of the networks. The nucleation and growth properties and aggregation of two lithocholyl amide derivatives were studied in several organic solvents using thermomicroscopy, as well as thermal control at macroscopic level. Nucleation/crystallization at interfaces was observed to act as the main route for the formation of microcrystalline fibers/solids in six gelator–solvent systems, in which spherulite formation …
Crystallization and microstructural development of nickel-containing aluminosilicate glasses with cordierite stoichiometry
2001
Abstract The crystallization behaviour of two glasses with chemical compositions MAl2O4/SiO2=1/2.5, being MNi and equimolar mixtures of Mg and Ni, was investigated. Glasses were prepared by cooling samples melted at 1650 °C. During thermal treatment over the range of temperature up to 1200 °C both glasses were first crystallized to form a β-quartz solid solution, then transformed to α-cordierite or spinel depending on the amount of nickel. The temperatures of both the crystallization of β-quartz solid solution and its further transformation were also dependent on the nominal amount of nickel. Lower temperatures were found for glasses with a large amount of nickel. UV–Vis diffuse reflectanc…
Effect of thermal treatment on the structural evolution of 3:2 and 2:1 mullite monophasic gels
2005
Abstract Single phase mullite gels with composition 3Al2O3 · 2SiO2 (3:2) and 2Al2O3 · SiO2 (2:1) were prepared by the semialkoxide method using aluminum nitrate nonahydrate and tetraethylorthosilicate as reagents. The influence of the thermal processing conditions on the reaction sequence was investigated. Both 3:2 and 2:1 mullite gels formed orthorhombic mullite under fast heating (40 °C/min) at 900 °C. Slow heatings delayed the formation of mullite in both gel compositions but no formation of spinel was detected between 1000 °C and 1100 °C. The slow transformation of pentacoordinated aluminum to octahedral and tetrahedral arrangements probably depends on the larger size and extent of the …
Cobalt aluminate spinel-mullite composites synthesized by sol-gel method
1997
Abstract CoAl 2 O 4 spinel-mullite composites were prepared by double substitution of Al by Ti and Ni in stoichiometric 3:2 mullite. Gels with compositions 3(Al 2 − 2 x Co x Ti x O 3 )·2SiO 2 (x = 0.025, 0.05 and 0.2) and 3(Al 2 − 2 x M x O 3 )·2SiO 2 (x = 0.05; M = Co 2+ or Ti 4+ ) were synthesized by sol-gel techniques. The structure of the gels was investigated by infra-red spectroscopy. Heating gels at 750 °C produced an amorphous silicoaluminate network. The reaction sequence was investigated by differential thermal analysis, X-ray diffraction and ultraviolet-visible spectroscopy. All samples crystallized at temperatures lower than 1000 °C from the amorphous state. Al-Si spinel and/or …
Coefficient of thermal expansion and elastic modulus of thin films
1999
The coefficient of thermal expansion (CTE), biaxial modulus, and stress of some amorphous semiconductors (a-Si:H, a-C:H, a-Ge:H, and a-GeCx:H) and metallic (Ag and Al) thin films were studied. The thermal expansion and the biaxial modulus were measured by the thermally induced bending technique. The stress of the metallic films, deposited by thermal evaporation (Ag and Al), is tensile, while that of the amorphous films deposited by sputtering (a-Si:H, a-Ge:H, and a-GeCx:H) and by glow discharge (a-C:H) is compressive. We observed that the coefficient of thermal expansion of the tetrahedral amorphous thin films prepared in this work, as well as that of the films reported in literature, depen…
Heterogeneous and Homogeneous Diffusivity in an Ion-Conducting Glass
1999
The nature of ion diffusivity in the vitreous conductor 2Ca NO3 2 ? 3KNO3 (CKN) was studied by nonresonant dielectric hole burning. Spectral holes in the electric field relaxation are probed subsequent to a high electric sinusoidal burn field. For sufficiently high pump frequencies we are able to induce spectrally selective modifications in the relaxation of the electric modulus, indicating that ionic diffusivity is a spatially varying quantity in glassy CKN. Homogeneous behavior occurs in the regime of low pump frequencies, in which the resistivity approaches its steady state value. Thus, longer-ranged ionic motions lead to a spatial averaging over the heterogeneity of local ion diffusivit…