Search results for "Thermoelastic Stress Analysis"
showing 8 items of 18 documents
Experimental evaluation of through-the-thickness stress distribution in transverse crack tension test samples
2015
Transverse Crack Tension (TCT) samples represent an alternative to End Notched Flexure configurations for the characterization of pure mode II fracture toughness of Fibre Reinforced Polymer composites. TCT is supposed to reproduce a pure Mode II failure mechanism while avoiding the frictional energy dissipation between the flanks of a starter crack. The TCT geometry is that of a unidirectional tensile sample where a number of embedded plies, centered on the middle plane, are cut in the transverse fibres direction. The tensile loading should then activate four symmetric fronts of mode II delamination from the transverse cut tips. The present work describes the implementation of two full fiel…
Rilevamento del segnale termoelastico a campo intero mediante analisi lock-in in modalità off-line
2014
Il presente lavoro propone una procedura di post-processamento del segnale termografico misurato su provini sollecitati in modo ciclico al fine di ricavare il segnale termoelastico. Dopo aver descritto la Correlazione Lock-In, usata tradizionalmente dai sistemi commerciali per ricavare il segnale termoelastico, il lavoro mostra come tale procedura sia numericamente equivalente alla determinazione delle armoniche della Trasformata di Fourier Discreta (TFD) del segnale campionato. Viene quindi proposta ed implementata una procedura di filtraggio del segnale termoelastico basata sulla applicazione diretta della TFD, che ha il vantaggio di poter in alcune circostanze fare a meno di un segnale d…
Lock-In Signal Post-Processing Techniques in Infra-Red Thermography for Materials Structural Evaluation
2013
This paper describes the potential of off-line thermographic signal processing by means of Lock-In Correlation algorithms, in order to implement structural health monitoring and stress analysis techniques. Thermal datasets acquired by infrared thermocameras are locked-in and correlated numerically with opportune reference signals, and amplitude and phase values of various harmonics retrieved by means of a Fast Fourier Transform and time averaging based filtering. This information is then processed for NDT defect probing and for evaluating the Thermoelastic Effect induced temperature changes. Two case studies in particular are discussed, implementing the proposed signal lock-in processing: a…
Quantitative thermoelastic stress analysis by means of low-cost setups
2020
Abstract A low-cost Thermoelastic Stress Analysis (TSA) experimental setup is proposed which uses an ordinary micro-bolometer and in-house developed signal processing scripts. The setup is evaluated by analysing the thermoelastic signal from a tensile and a SENT specimen made of stainless steel AISI 304L, and the bolometer performances are compared with those of a state of the art photon detector. Signal processing is based on off-line cross-correlation, using a self-reference signal which is retrieved from the acquired thermal data. Procedures are in particular developed to recognise, quantify and correct errors due to spectral leakage and loss of streamed frames. The thermoelastic signal …
Investigation on the influence of the surface resin rich layer on the thermoelastic signal from different composite laminate lay-ups
2006
This work presents a set of experimental results based on the measured thermoelastic signal from GRP composite coupons adopting different lay-ups. A comparison is made with the thermoelastic signal predicted by two different analytical models: one based on the classical law of the thermoelastic effect for orthotropic materials, and the other based on a novel theory accounting for the presence of a resin layer on the external surface of the composite structure. The composite coupons were designed such to determine a significant difference in the predictions made by the two theoretical models. Experimental results have shown a far better match with the predictions based on the novel theory ac…
Investigation of the Thermomechanical Response of Cyclically Loaded NiTi Alloys by Means of Temperature Frequency Domain Analyses
2021
Nickel–Titanium (NiTi) shape memory alloys subjected to cyclic loading exhibit reversible temperature changes whose modulation is correlated with the applied load. This reveals the presence of reversible thermomechanical heat sources activated by the applied stresses. One such source is the elastocaloric effect, accounting for the latent heat of Austenite–Martensite phase transformation. It is, however, observed that when the amplitude of cyclic loads is not sufficient to activate or further propagate this phase transformation, the material still exhibits a strong cyclic temperature modulation. The present work investigates the thermomechanical behaviour of NiTi under such low-amplitude cyc…
Thermo-Mechanical Behaviour of Flax-Fibre Reinforced Epoxy Laminates for Industrial Applications
2015
The present work describes the experimental mechanical characterisation of a natural flax fibre reinforced epoxy polymer composite. A commercial plain woven quasi-unidirectional flax fabric with spun-twisted yarns is employed in particular, as well as unidirectional composite panels manufactured with three techniques: hand-lay-up, vacuum bagging and resin infusion. The stiffness and strength behaviours are investigated under both monotonic and low-cycle fatigue loadings. The analysed material has, in particular, shown a typical bilinear behaviour under pure traction, with a knee yield point occurring at a rather low stress value, after which the material tensile stiffness is significantly r…
A Quantitative Analysis of the Thermoelastic Effect in CFRP Composite Materials
2010
In this study the thermoelastic signal from carbon fibre-reinforced plastic (CFRP) laminates is investigated. A comparison between the theoretical and experimental values of the thermoelastic signal is reported, with the theoretical predictions obtained from two different quantitative models. These models are based on the classic thermoelastic effect law extended to the case of orthotropic materials (by using the mesomechanical or bulk approach), and the modified law assuming that the surface resin-rich layer behaves as a strain witness of the laminate. It is found that the theoretical predictions of the two models can be strongly and differently influenced by the intrinsic orthotropy of ca…