Search results for "Tio2"

Photocatalytic degradation of 4-nitrophenol in aqueous suspension by Using Functionalized Porphyrin-TiO2 Photocatalysis Under Visible Irradiation

2007

Environmentally Friendly Photocatalytic Oxidation of Aromatic Alcohol to Aldehyde in Aqueous Suspension of Brookite TiO(2)

2008

WOS: 000260509000008

Brookite, the Least Known TiO2 Photocatalyst

2013

Brookite is the least studied TiO2 photocatalyst due to the difficulties usually encountered in order to obtain it as a pure phase. In this review, a comprehensive survey of the different methods available for preparing brookite powders and films is reported. Attention has been paid both to the most traditional methods, such as hydrothermal processes at high temperatures and pressures, and to environmentally benign syntheses using water soluble compounds and water as the solvent. Papers reporting the photocatalytic activity of pure and brookite-based samples have been reviewed.

Photocatalytic oxidation of aromatic alcohols to aldehydes in aqueous suspension of home prepared titanium dioxide: 2. Intrinsic and surface features…

2008

Some intrinsic electronic properties of home prepared (HP) TiO2 catalysts were investigated by diffuse reflectance spectroscopy and quasi-Fermi level measurements. These powders were used for carrying out the photocatalytic oxidation of benzyl alcohol to benzaldehyde and CO2 in water; the selectivity for aldehyde formation was enhanced by the addition of small amounts of ethanol, a typical hole trap. The values of band gap, valence band and conduction band edges are almost identical for all the HP samples in which anatase phase is predominant, whereas appreciable differences can be noticed for an HP sample containing high amount of rutile phase. A comparative ATR-FTIR study of the HP cataly…

Junction Effect on the Photocatalytic Activity of Mixed-Phase TiO2 Nanoparticles

2010

Active TiO2 photocatalysts were prepared under mild experimental conditions by thermohydrolysis of TiCl4 in pure water at 100 {degree sign}C. The preparation method is very simple and does not require the use of expensive thermal or hydrothermal treatments. Depending on the TiCl4/H2O ratio, pure rutile, binary mixtures of anatase and rutile or anatase and brookite, or ternary mixtures of anatase, brookite and rutile, can be obtained. 4-nitrophenol photodegradation was used to evaluate the photoactivity of the various powders. The high photocatalytic activity of the mixed samples was explained by the presence of junctions among different polymorphic TiO2 phases that allows an improved charge…

Photocatalytic Selective Oxidation of 5-(Hydroxymethyl)-2-furaldehyde to 2,5-Furandicarbaldehyde in Water by Using Anatase, Rutile, and Brookite TiO2…

2013

5-(Hydroxymethyl)-2-furaldehyde (HMF) was selectively oxidized to 2,5-furandicarbaldehyde (FDC) in; aqueous medium by using home prepared (HP) anatase, rutile, and brookite TiO2 nanoparticles. HP samples were prepared via a sol-gel method by using TiCl4 as the TiO2 precursor. Commercial TiO2 catalysts were also used for, comparison. All samples were characterized by BET specific surface area, XRD, TGA, and SEM, and the reactivity results showed that HP catalysts are predominantly amorphous and give rise to selectivities toward FDC more than twice that of commercial and well crystallized catalysts.

ZnO/ZnS heterostructures for hydrogen production by photoelectrochemical water splitting

2016

This work studies the photoelectrochemical behavior of novel ZnO/ZnS heterostructures obtained by means of anodization in water and glycerol/water/NH4F electrolytes with different Na2S additions under controlled hydrodynamic conditions. For this purpose different techniques such as Field Emission Scanning Electronic Microscopy (FE-SEM) with EDX, Raman spectroscopy and photoelectrochemical water splitting tests under standard AM 1.5 conditions have been carried out. The obtained results showed that the hydrodynamic conditions promoted an ordered nanotubular morphology which facilitates electron-hole separation and consequently, the photoelectrochemical activity for water splitting is enhance…

Influence of annealing atmosphere on photoelectrochemical response of TiO2 nanotubes anodized under controlled hydrodynamic conditions

2021

[EN] The influence of three annealing atmospheres (air, nitrogen and argon) and the use of controlled hydrodynamic conditions (from 0 to 5000 rpm) on morphological, structural, chemical and photoelectrochemical properties of TiO2 nanotubes have been evaluated. For this purpose, different characterization techniques have been used: Field Emission Scanning Electron Microscopy, Raman Confocal Laser Spectroscopy, X-Ray Diffraction, X-Ray Photoelectron Spectroscopy, Incident Photon-to-electron Conversion Efficiency measurements, ultraviolet-visible absorption spectra, Mott-Schottky analysis and photoelectrochemical water splitting tests. According to the results, it can be concluded that both hy…

Structural and Optical Properties of Novel Surfactant Coated TiO2–Ag Based Nanoparticles

2010

Stable dispersions of surfactant-coated TiO2–Ag based nanoparticles in apolar medium have been prepared by performing sequentially the hydrolysis of titanium(IV) isopropoxide and the reduction of Ag? in the confined space of sodium bis(2-ethylhexyl)sulfosuccinate (NaAOT) reverse micelles. Depending on the sequence length, this novel procedure allowed the synthesis of semiconductor–metal nanoparticles, nominally indicated as TiO2/Ag, TiO2/Ag/TiO2, and TiO2/Ag/TiO2/ Ag, stabilized by a monolayer of oriented surfactant molecules. The structural characterization of these nanoparticles has been performed by High Resolution Transmission Electron Microscopy (HR-TEM), while optical properties were …

Tensile strength and impact strength of color modified acrylic resin reinforced with titanium dioxide nanoparticles

2017

Background Poor mechanical properties are among the main limitations of acrylic resins. Addition of titanium dioxide (TiO2) nanoparticles to acrylic resin has been shown to improve its mechanical properties with an adverse effect on its color. Thus, this study sought to assess the tensile and impact strength of a color modified heat cure acrylic resin reinforced with TiO2 nanoparticles. Material and Methods In this in vitroexperimental study, 1wt% TiO2 nanoparticles were added to SR Triplex Hot heat-cure acrylic resin powder and mixed. Pigments and color fibers were also added and 18 samples were fabricated of this paste for tensile and impact strength testing (n=9) according to ISO5271. Ei…