Search results for "Titan"

Technological aspects regarding machining the titanium alloys by means of incremental forming

2017

Titanium alloys are materials with reduced formability, due to their low plasticity. However, today there are high demands regarding their use in the automotive industry and in bio-medical industry, for prosthetic devices. This paper presents some technological aspects regarding the machinability of titanium alloys by means of incremental forming. The research presented in this paper aimed to demonstrate that the parts made from these materials could be machined at room temperature, in certain technological conditions.

Nanostructuring with a crosslinkable discotic material.

2007

A high-yielding synthesis afforded a hexa-peri-hexabenzocoronene carrying acrylate units at the end of six attached alkyl spacers. The polymerization of these acrylate moieties could be initiated with thermal energy and through direct photoactivation without the addition of a photoinitiator. This allowed the organization of the liquid-crystalline material to be fixed in either the crystalline state or the mesophase, which preserved the organization in the respective phase. The use of a focused synchrotron beam permitted selected regions of a thin film to be rendered insoluble. After "developing" the film in this lithographic process by dissolving the soluble, unpolymerized material, defined…

Generation and characterization of T40/A5754 interfaces with lasers

2014

Laser-induced reactive wetting and brazing of T40 titanium with A5754 aluminum alloy with 1.5 mm thickness was carried out in lap-joint configuration, with or without the use of Al5Si filler wire. A 2.4 mm diameter laser spot was positioned on the aluminum side to provoke spreading and wetting of the lower titanium sheet, with relatively low scanning speeds (0.1 to 0.6 m/min). Process conditions did not play a very significant role on mechanical strengths, which were shown to reach 250-300 N/mm on a large range of laser power and scanning speeds. In all cases considered, the fracture during tensile testing occurred next to the TiAl3 interface, but in the aluminum fusion zone. In a second st…

Beta forging of Ti-6Al-4V: Microstructure evolution and mechanical properties

2013

Titanium alloys are finding an increasing use in the aeronautical field, due to their characteristics of high mechanical properties, lightness and corrosion resistance. Moreover these alloys are compatible with the carbon fibre reinforced plastics that are also finding a wide use in the aeronautical field. On the other hand the use of these alloys implies some drawbacks, for example titanium alloys are often considered more difficult to form and generally have less predictable forming characteristics than other metallic alloys such as steel and aluminum. In this paper was studied both the microstructure evolution and the mechanical properties of a Ti-6Al-4V rolled bar after hot forging. The…

High Electromechanical Coupling in Relaxor Pb(Sc<sub>1/2</sub>Nb<sub>1/2</sub>) O<sub>3</sub> - PbTiO<sub>3…

1997

Scale composition and oxidation mechanism of the Ti–46Al–8Nb alloy in air at 700 and 800 °C

2011

It is known that the oxide scale formed on TiAl alloys is generally composed of a mixture of alumina (Al2O3) and titania (TiO2). The presence of niobium changes the activities of Ti and Al and influences the kinetics of oxidation and oxide layer composition. In this work, the Tie46Ale8Nb alloy was subjected to cyclic oxidation in air at 700 � C (for 2 and 24 h) and 800 � C (for 300 h). Scale composition was analyzed by means of different techniques including X-ray photoelectron spectroscopy, X-ray diffraction and secondary ion mass spectroscopy. The scale consisted of several layers. The outer layer was built of alumina (amorphous or with very fine grains), whereas the inner layer e mainly …

Oxidation mechanism of the Inconel 601 alloy at high temperatures

2010

The Inconel 601 alloy oxidation was performed in air, in the temperature range 1000-1150 °C, during 90 h. Kinetic results show that the parabolic behavior is always followed in this temperature range. The Arrhenius plot of the kp values shows two different activation energies. Between 1000 and 1050 °C the activation energy is E a1 = 160 ± 10 kJ/mol. In the 1050-1150 °C temperature range a higher value is calculated E a2 = 252 ± 20 kJ/mol. The E a2 value and the X-ray diffraction (XRD) results and scanning electron microscope (SEM) energy dispersive X-ray spectroscopy (EDS) examinations are in accordance with a scale growth mechanism limited by a growing Cr 2 O 3 scale acting as a diffusion …

Sheet metal forming of titanium blanks using flexible media

1998

Abstract Sheet metal forming processes using flexible media are increasingly utilized in the industrial practice due to the relatively low tooling cost. In the present investigation, a rubber forming process is applied to the manufacturing cycle of a titanium alloy component for acoustic tweeters. The proposed process allows a reduction in manufacturing costs and production time since it permits the elimination of some joining operations. The FEM analysis has permitted the definition of the optimal process parameters and tooling geometry. Accordingly, several components have been produced; the achieved quality level is comparable with the one obtained utilizing the conventional technology a…

Evolution of microstructures and mechanical properties during dissimilar electron beam welding of titanium alloy to stainless steel via copper interl…

2013

Abstract The influence of operational parameters on the local phase composition and mechanical stability of the electron beam welds between titanium alloy and AISI 316L austenitic stainless steel with a copper foil as an intermediate layer has been studied. It was shown that two types of weld morphologies could be obtained depending on beam offset from the center line. Beam shift toward the titanium alloy side results in formation of a large amount of the brittle TiFe2 phase, which is located at the steel/melted zone interface and leads to reducing the mechanical resistance of the weld. Beam shift toward the steel side inhibits the melting of titanium alloy and, so, the formation of brittle…

Computer Aided Design of an Effective Fixture for FSW Processes of Titanium Alloys

2011

During the last years welded titanium components have been extensively applied in aeronautical and aerospace industries because of their high specific strength and corrosion resistance properties. Friction Stir Welding (FSW) is a solid state welding process, currently industrially utilized for difficult to be welded or “unweldable” aluminum and magnesium alloys, able to overcome the drawbacks of traditional fusion welding techniques. When titanium alloys are concerned, additional problems arise as the need for very high strength and high temperature resistant tools, gas shield protection and high stiffness machines. Additionally, the process is characterized by an elevated sensitivity to te…