Search results for "Titani"
showing 10 items of 931 documents
Defects at the TiO2(100) surface probed by resonant photoelectron diffraction.
2006
We report photoelectron diffraction (PED) experiments of weakly sub-stoichiometric TiO 2 (100) rutile surfaces. Apart from standard core-level PED from the Ti-2p3/2 line, we have studied valence band PED from the defect induced Ti-3d states in the insulating band gap. For maximum yield, the latter were resonantly excited at the Ti-2p absorption edge. The PED patterns have been analyzed within the forward scattering approximation as well as by comparison with simulated PED patterns obtained in multiple scattering calculations. The analysis shows that the defect induced Ti-3d charge is mainly located on the second layer Ti atoms. © 2007 Elsevier B.V. All rights reserved.
Preparation of photocatalytic brookite thin films
2007
Pure brookite films were deposited from a brookite dispersion obtained by peptizing a mixture brookite–rutile prepared by thermolysis of TiCl4 in a HCl solution. The films were characterised by X-ray diffraction and Raman spectroscopy. The photoactivity of the samples was tested by using the photo-oxidation of 2-propanol in gas–solid regime as a probe reaction. The brookite films efficiently degraded 2-propanol under UV illumination.
Pressure-induced transition in titanium metal: a systematic study of the effects of uniaxial stress
2005
Abstract The effects of uniaxial stress on the pressure-induced α → ω transition in pure titanium (Ti) are investigated by means of angle dispersive X-ray diffraction in a diamond-anvil cell. Experiments under four different pressure environments reveal that: (1) the onset of the transition depends on the pressure medium used, going from 4.9 GPa (no pressure medium) to 10.5 GPa (argon pressure medium); (2) the α and ω phases coexist over a rather large pressure range, which depends on the pressure medium employed; (3) the hysteresis and quenchability of the ω phase is affected by differences in the sample pressure environment; and (4) a short-term laser heating of Ti lowers the α → ω transi…
Synthesis and structural study of sodium titanium phosphate-sodium tin phosphate solid solutions. II. Thermal expansion
1993
Abstract The structure of NaTi 2 (PO 4 ) 3 shows the space group R3c, whereas that of NaSn 2 (PO 4 ) 3 presents the space group R3 at room temperature and it undergoes a second order phase transition at 575°C from this structure to another with the space group R3c. Evolution of the structure of NaTi 2 (PO 4 ) 3 NaSn 2 (PO 4 ) 3 solid solutions with temperature has been studied and temperature phase transition established for the compositions studied. Lattice thermal expansion of NaTi 2−x Sn x (PO 4 ) 3 solid solutions with x = 1, 1.2, 1.5 has been determined from x-ray diffraction data at temperatures ranging from 26 to 1000°C. DSC and dilatometric measurements have been also carried out o…
Linker depletion for missing cluster defects in non-UiO Metal-Organic Frameworks
2021
Defect engineering is a valuable tool to tune the properties of metal–organic frameworks. However, defect chemistry remains still predominantly limited to UiO-type MOFs. We describe the preferential formation of missing cluster defects in heterometallic titanium–organic frameworks of the MUV-10 family when synthesised in sub-stoichiometric linker conditions. Our results show the value of integrating experimental work, computational modelling and thorough characterization in rationalizing the impact of defects over the porosity and structure of this family of materials. Correlation of experiment with computational models reveals the dominance of missing cluster vacancies in the pore size dis…
A multi-step mechanism and integrity of titanate nanoribbons.
2014
A one-step hydrothermal treatment of TiO2 powders under strongly basic conditions has been used to synthesize titanate nanoribbons. The nanoparticles were thoroughly characterized using several methods including transmission electron microscopy (TEM), X-ray diffraction (XRD), Raman spectroscopy and X-ray photoelectron spectrometry (XPS) to determine their morphological, structural and chemical characteristics. The influence of the nature and size of the TiO2 precursor and of the reaction duration on the formation of the nanoribbons was investigated. The conditions required to obtain only titanate nanoribbons with a width ranging from 100 to 200 nm and several tens of micrometers in length w…
Intrinsic Nature of the Excess Electron Distribution at theTiO2(110)Surface
2012
The gap state that appears upon reduction of TiO2 plays a key role in many of titania's interesting properties but its origin and spatial localization have remained unclear. In the present work, the TiO2(110) surface is reduced in a chemically controlled way by sodium adsorption. By means of resonant photoelectron diffraction, excess electrons are shown to be distributed mainly on subsurface Ti sites strikingly similar to the defective TiO2(110) surface, while any significant contribution from interstitial Ti ions is discarded. In agreement with first principles calculations, these findings demonstrate that the distribution of the band gap charge is an intrinsic property of TiO2(110), indep…
Inorganic gels as precursors of TiO2 photocatalysts prepared by low temperature microwave or thermal treatment
2008
Abstract A simple procedure for preparing active TiO2 photocatalysts is presented. The starting materials were unusual TiO2 gels formed from TiCl4. The use of microwaves for a very short time enhanced the TiO2 crystallinity preventing an increase of particle size and minimizing the decrease of specific surface area. This result makes this preparation very attractive. The formation of the gels was monitored through measurements of viscosity. All the samples were characterized by means of X-ray diffraction, diffuse reflectance spectroscopy and BET specific surface area measurements. The photoactivity of the samples was evaluated using the photodegradation of 4-nitrophenol in liquid–solid regi…
Study of the high temperature behaviour of titanium alloy Ti6242S under complex atmospheres : aeronautical applications
2018
The use of titanium alloys in many applications (transport, energy, chemistry,...) allows significant weight savings in relation to the good mechanical properties/density ratio of these materials. Since titanium alloys are employed at high temperatures (T>500°C), their behavior in such conditions has to be studied in severe conditions in order to understand degradation mechanisms. Moreover, some specific conditions can be met during application, like thermal cycling, water vapour or presence of salts. These parameters are known to influence oxidation behavior of titanium alloys.In this thesis work, oxidation behavior of an aeronautics titanium alloy (Ti6242S) has been studied in air and moi…
Photocatalytic ozonation under visible light for the remediation of water effluents and its integration with an electro-membrane bioreactor
2018
Abstract Photocatalysis and photocatalytic ozonation under visible light have been applied for the purification of a complex aqueous matrix such as the grey water of Masdar City (UAE), by using N-doped brookite-rutile catalysts. Preliminary runs on 4-nitrophenol (4-NP) solutions allowed to test the reaction system in the presence of a model pollutant and to afford the relevant kinetic parameters of the process. Subsequently, the remediation of grey water effluent has been evaluated in terms of the reduction of total organic carbon (TOC) and bacterial counts. The concentration of the most abundant inorganic ionic species in the effluent has been also monitored during reaction. Photocatalytic…